Lightolier C4AICLV User manual

9 1/4"
10"
18"
MAX
24" O.C.
LOCKING SCREW
J-BOX
COVER
FRAME-IN
Locate fixture along joist and line up bottom edge of HINGED
MOUNTING BAR with the bottom of joist and fasten in place.
FOR JOIST SPACING LESS THAN 16” ON CENTER
(TO 12” ON CENTER):
• MOUNTING BAR CHANNELS can be shortened and used as
nailing legs in tight places. Simply remove INNER BAR from
holed CHANNEL, bend CHANNEL at appropriate point and use
extra screw to secure it to the joist.
WIRE-IN
Wire to SUPPLY LEADS. WHITE FIXTURE LEAD to NEUTRAL
SUPPLY LEAD. BLACK FIXTURE LEAD to HOT (120v) SUPPLY LEAD.
For 277V connect RED FIXTURE LEAD to HOT SUPPLY LEAD.
BARE FIXTURE WIRE to SUPPLY GROUND. Use wirenuts (local hard-
ware item). Place all electrical connections in the J-Box and close
the J-BOX COVER.
NOTE: To inspect splices, leave min 8" of lead wire in J-Box.
SWING-UP
Extend MOUNTING BAR to reach opposite joist and fasten in place.
Adjust fixture to desired position along MOUNTING BAR and lock in
place using locking screw
AIRSEAL®INSTALLATION (optional)
Install a bead of silicone caulking compound between the
ceiling opening and edge of HOUSING. Housings are tested in
accordance with ASTM E 283 (max 2 cfm @ 75 pa) and comply
with WSEC & MEC when installed as instructed.
CLOSE-IN
Close in ceiling as required.
INSTALLING SOCKET HARNESS
INSTALLING HOUSING TRIMS
FIXTURE TRIM ADJUSTMENT
READ AND UNDERSTAND THESE INSTRUCTIONS bEFORE INSTALLING FIXTURE
This fixture is intended for installation in accordance with the National Electrical Code and local
regulations. To assure full compliance with local codes and regulations, check with your local electrical
inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
LIGHTOLIER a GENLYTE THOMAS company.
631 Airport Road, Fall River, MA 02720
INSTRUCTION SHEET NO.
IS:CICLV
A1099 Page 1 of 2
INSTALLATION PROCEDURE FOR LOW VOLTAGE
INSULATED CEILING (TYPE-1C) FRAME-IN-KITS: C4AICLV, C6AICLV
SEE SEPARATE
REFLECTOR TRIM
INSTRUCTION
SHEETS
J-BOX
COVER
CHANNEL MOUNTING BAR
HINGED
MOUNTING BAR

READ AND UNDERSTAND THESE INSTRUCTIONS bEFORE INSTALLING FIXTURE
This fixture is intended for installation in accordance with the National Electrical Code and local
regulations. To assure full compliance with local codes and regulations, check with your local electrical
inspector before installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
INSTRUCTION SHEET NO.
IS:CICLV
A1099 Page 2 of 2
LIGHTOLIER a GENLYTE THOMAS company.
631 Airport Road, Fall River, MA 02720
TRANSFORMER REPLACEMENT
• Make sure power to fixture is off.
• Remove REFLECTOR TRIM from ceiling by twisting counter-clock-
wise and pulling down.
• Disconnect & remove SOCKET HARNESS from TRANSFORMER
ASSEMBLY.
• Disconnect POWER SUPPLY HARNESS: For C4AICLV disconnect
harness at TRANSFORMER COVER. For C6AICLV disconnect har-
ness from junction box assembly (opposite side of fixture from
TRANSFORMER ASSEMBLY).
• Remove (2) THUMB SCREWS.
• Remove TRANSFORMER COVER from THUMB SCREW studs
• Pull TRANSFORMER ASSEMBLY and TRANSFORMER COVER into
FIXTURE HOUSING and out through aperture opening.
• Disconnect TRANSFORMER wiring from THERMAL PROTECTOR(S)
and TRANSFORMER CONNECTORS. Refer to TRANSFORMER
WIRING DIAGRAMS shown below for your particular MODEL AS
INDICATED.
• Remove TRANSFORMER MOUNTING HARDWARE and discard faulty
TRANSFORMER.
• Install new TRANSFORMER in reverse order of removal.
WARNING: Risk of fire. Fixture contains THERMAL PROTECTORS that
must be rewired as shown in DIAGRAMs below. Use only
replacement TRANSFORMER obtained from LIGHTOLIER
INSTALLATION PROCEDURE FOR LOW VOLTAGE
INSULATED CEILING (TYPE-1C) FRAME-IN-KITS: C4AICLV, C6AICLV
WHITE
WHITE
WHITE
RED
WHITE
WHITE
WHITE
BLUE
TRANFORMER WIRING DIAGRAM
RED
WHITE
BLACK
WHITE
RED WHITE
WHITE
RED
PRI SEC
BLACK
HARNESS CONNECTOR
POWER SUPPLY
BLACK
SECPRI
WHITE
WHITE
WHITE
WHITE BLACK
PROTECTORS
THERMAL
WHITE
RED
TRANSFORMER ASSEMbLY
COVER
TRANSFORMER
THUMB SCREW
MOUNTING HARDWARE
TRANSFORMER
TRANSFORMER
CONNECTOR
SOCKET HARNESS
MODEL C4AICLV
TRANFORMER WIRING DIAGRAM
MODEL C6AICLV
HOUSING
TRANSFORMER
HOUSING
FIXTURE
CONNECTOR
TRANSFORMER
TRANSFORMER
BLACK
BLACK
PROTECTORS
THERMAL
5.5 V
CONNECTOR
HARNESS
SOCKET
12 V
CONNECTOR
HARNESS
SOCKET
(TO J-BOX)
CONNECTOR
SUPPLY
POWER
NOTE: 1. LOW VOLTAGE FIXTURES should be dimmed only
with special dimmers intended specifically for that purpose.
Use Lightolier Lytemode, Scenist, Crescendo VA, Neptune VA,
Precision VA, EasySet VA, Sunrise VA, Radiant VA or equiva-
lent products by others or variable autotransformers or elec-
tronic dimmers intended for use with low voltage fixtures.
2. Low voltage fixtures produce audible sound which may be
objectionable in acoustically critical areas.