Lightolier Calculite Remodeler Kits User manual

1
.—
(INSTRUCTION SHEET NO.
INSTALLATION PROCEDURE FOR CALCULITE@
REMODELER Kl~ IS:A400RM
0890 Page 1M2
READ AND UNDER=AND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE.
This fixture is intended for installation in accordance with the National Electrical Code and local regulations.
To assure full compliance with local codes and regulations, check with your local electrical inspector before
ii%tallation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference
WARNING—(RISK OF FIRE) DO NOTINWALLINSULATIONWITHIN 3INCHESOF FIXTURE SIDES OR
WIRING COMPARTMENT, NOR ABOVE FIXTURE IN SUCH AMANNER TO ENTRAP HEAT.
EXISllNG CONSTRUCllON
%pp
“...,.,. .,, t. ‘,, ‘
e
Ca
8
10 e
FIG. AFIG. BFIG. C
LCUT OPENING Il. WIRE-IN Ill. ATTACH J-BOX
L
II.
CUT OPENING (Fig. A)
Use MOUNTING RING provided as atemplate to
cut ahole in the ceiling. Use inside diameter to
SCribe hole.
WIRE-IN (Fig. B)
Wire to suppl~leads. (For Cable, use built-in Cable
Clamp in J-Box.) White fixture lead to neutral supply
lead. Black fixture lead to hot (120V) supply lead.
Bare fixture wire to supply ground. Use wirenuts
(local hardware item). Place all electrical
connections in the J-BOX. Attach J-BOX COVER
onto J-BOX.
Ill. AITACH J-BOX (Fig. C&G)
1. Attach J-BOX PLATE to ceiling by pushing NAIL
TAB on J-BOX PiATE into ceiling, Fig. G.
2. Push LONG LEG of NAIL CLIPS (supplied in
parts bag) into RAISED BUMP of J-BOX PIATE
and SHORT LEG into ceiling, Fig. G.
3. Make sure that the J-BOX PLATE is securely
attached to the ceiling and the J-BOX is in the
position shown in Fig. G.
FIG. D
IV. AITACH
MOUNTING RING
FIG. EFIG. F
V. SNAPON VI. PUSH-UP
THERMAL
PROTECTOR
7
~J.BOX PLATE
LONG LEG -RAISED BUMP
FiG. G

IV. A~ACH MOUNTING RING
Insert MOUNTING RING into CEILING as shown
(Fig. H).
CLIP ASSEMBLY (Fig. 1)
1. Insert CLIP from inside housing, through ‘T’ slot.
2. Apply downward force with screwdriver on top of
CLIP or engage screwdriver in slot in CLIPS flange.
3. Apply force until CLIP is snugly seated.
LoT
PRING
CLIP REMOVAL (Fig. J)
1. Insert asmall blade, short-handled screwdriver
through the CLIPS’S screwdriver slot, and press
against the opposite side of the CLIP
2. Push CLIP up to top of ‘T’ SD and remove.
V. SNAPON (Fig. E) ISEE SEPARATE
REFLECTOR TRIM
INSTRUCTION
VI. PUSH-UP (Fig. F) SHEETS
C“L”G\’&, 7
‘w,
[.
FIG. H
TO INSERT ‘f INSIDE OF
\HOUSING
Y
\
‘., rSTEP 1
T1
... ,
,(
‘T SLOT SHORT HANDLE
IN HOUSING JSCREWDRIVER
STEP 2
_.
*’ STEP 3
LJ
LcI=lL1’G
FIG. I
FIG. J
t4
WARNING: USE 0NL% REFLECiOR TRIMS PROVIDED BY LIGHTOLIER INC. USE OF UTHER
MANUFACTURERS’ REFLECTOR TRIMS VOIDS THE UNDERWRITERS LABORATORIES LISTING AND
COULD CONSTITUTE AflRE HAZARD.