Lightolier COIL CORD CLAMP-ON MONOPOINT User manual

v
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE INSTRUCTION SHEET NO.
ThisfixtureisintendedforinstallationinaccordancewiththeNationalElectricalCodeandlocalregulations.
Toassurefull compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electrical shock, turn off electricity at fuse box before proceeding. IS:6196
Retain these instructionsfor maintenance reference. A1294 Page 1of2
INSTRUCTIONS FOR ATTACHING COIL CORD CLAMP-ON MONOPOINT
FORUSE WITH LIGHTOLIER TRACK FIXTURES ONLY
ATTACHING COILEDCORDCLAMP-ON MONOPOINT TIGHTENING KNOB
TO PIPE ORPIPESTRUCTURE
This CLAMP is designed to mount on round pipe, pipe structures, PIPE OUTSlOE
or round supports. Secure the CLAMP to structure by tightening DIAMETER 5/8” TO 2“
the TIGHTENING KNOB and the body allowed to face downward RECOMMENCED
CLAMP
to minimize force required to support I_ytespots (Fig. 1). A(3)
prong 120V, 60 Hz, grounded receptacle is required to energize
the unit,
MONOPOINT
AllACHING LYTESPOTWITH “T’ ADAPTORTO COIL AOAPTOR
CORDCLAMP FIG. 1
1.Position LEVER as shown in Fig. 2,
2. Align BEAD on MONOPOINT ADAPTOR with GROOVE in “T”
adaptor, see Fig. 2(If BEAD is NOT aligned, apotential hazard
may result). Rotate LEVER 90 degrees to secure Lytespot.
3. To remove !_ytespot: Hold fixture and rotate LEVER 90 degrees
(Fig. 3).
CAUTION-INJURY TO PERSONS AND DAMAGE TO
THE LAMP AND/OR MOUNTING SURFACE MAY RESULT
IF THE LAMP IS PULLED FROM THE SURFACE. TO co
REDUCE THE LIKELIHOOD OF SUCH INJURY OR
DAMAGE, MOUNT ONLY ON ASURFACE THAT IS
MECHANICALLY SOUND. GAS
FIG. 2GROUNO
,,
u
FIG. 4FIG. 3
1-I C3HTC> LIER“
E~~~~f~;,N~~
‘T” ADAPTOR(lDIA. SHAIT)
JSEDWITHCAT.NO.S6435&BOXADAPTOR
7599
zE
NOTE:Not designed to work with
COIL CORD CLAMP-ON MONOPOINT

INSTRUCTIONSHEETNO.
1S:6196 INSTRUCTIONS FOR AITACHING COIL CORD CLAMP-ON
MONOPOINT (Cent’d)
FORUSEWITH LIGHTOLIERTRACKFIXTURESONLY
A1294 Page 2of 2
INSTRUCTIONS FORATTACHING LYTESPOT WITH SQUAT ADAPTOR TO COIL CORD CLAMP
1, Insertthe SQUATADAPTERinto the MONOPOINTADAPTOR.The LOCKING LEVER must be on the same side as the BEAD located on the
MONOPOINT ADAPTOR (See Fig. 5). Rotate the SQUAT ADAPTOR 90 degrees clockwise until LOCKING LEVER locks into place (See Fig. 5,
6&7).
2. To remove, depress LOCKING LEVER and rotate SQUAT ADAPTOR 90 degrees counterclockwise.
ICAUTION-SUPPORT THE MONOPOINT ADAPTOR WHENEVER MANIPULATING THE FIXTURE. I
MONOPOINT
ADAPTOR
LOCKING SQUAT
LEVER ADAPTOR
L*1
BEAD &
‘*
FIG.5FIG.6FIG.7
INSTRUCTIONS FORAllACHING LOW VOLTAGE TO COIL CORD CLAMP
1.Insert the LOW VOLTAGE ADAPTOR into the MONOPOINT ADAPTOR. The LOCKING LEVER must be on the same side as
on the MONOPOINT ADAPTOR (See Fig. 8). Rotate the LOW VOLTAGE ADAPTOR 90 degrees clockwise to secure fixture
electrical connection (See Fig. 8,9 &10).
2, To remove, rotate LOW VOLTAGE ADAPTOR 90 degrees counterclockwise.
ICAUTION-SUPPORT THE MONOPOINT ADAPTOR WHENEVER MANIPULATING THE FIXTURE. I
wMONOPOINT RFAD —ADAPTOR
“-”--::AGE
LOCKING ~
LEVER /ADAPTOR
FIG.8FIG.9
%
FIG. 10
the BEAD located
and make
—