Lightolier reflector trim User manual

INSTALLATION OF LYTECASTER REFLECTOR TRIM 151152.A
IN THE 1102 FRAME-IN-KIT WITH ROTO CLIPS 0690
Page2of 2
TRIM lNSTALLATtON(Contd) INSULATING SLEEVING >-MA! FC.ONNHTCIRS
INSTALL LAMP “.. /{At~aci;di;”50CGt-tik.,
NmE Sooket manufactures have suggested
that socket may fall after 3to 6ralampinge. If
thla occurs sooket cart be replaced by
dlaconnectlng male connectom (anached to
socket Ieada) from female connectors
(attached to flstura leads) and replacing it
with asocket procured through Lightoller,
see Fig. L
FEMALE CONNECTORS
(Attached to Fixture WE.) MR16 SOCKET
FIG. I
7. Remove LAMP RING from IAMPNOKE HOLDER by
pulling straight down (Fig. J),
8. Insert LAMP (MR-16 Bulb) between LAMP SPRINGS
until face of bulb sits firmly on GLASS LAMP
GUARD (Fig. K).
9. Attach SOCKET to hi-pin prungs on LAMP (Fig. K),
(NUIT% No polarity of pins required).
10. Insert LAMP RING with LAMP and GLASS LAMP
GUARD attached back into IAMPNOKE HOLDER.
VERTICAUANGLE ADJUSTMENT AND LOCK
11. Insert ascrewdriver into the LOCKING GUIDE on the
LAMPNOKE HOLDER, and locate the slot in the
VERTICAL ADJUST/lQCK SCREW. turn the SCREW.
counterclockwise+ and using the screwdriver as a‘
lever, tilt the entire LAMP/’fOKE HOLDER to the
desired angle. Once the desired angle is reached,
tighten ecraw by turning screwdriver clockwise until
snug tight.
HORIZONTAL ADJUST AND LOCK
12. The entire lAMP/YOKE HOLDER can be horizontally
rotated to aim the angle of light through the hole in
the FACE PLATE TRIM (Fig. K). This can be done by
racking off the HORIZONTAL ADJUST/~CK SCREW
one full turn freein the SUPPORT PIATE (Fig. K).
8
Grasping the YOKE on either side of the LAMPNOKE
HOLDER. rotate the SUPPORT PLATE to tha desired
angle, and lock the poeition by tightening” the
HORIZONTAL ADJUSWU3CK SCREW. Replete INSERTS
13, Insert PINHOLE FACEPLATE,
““’’’K’v%
G
~– -’
FIG. J
RELAMPING The locking mechanism in this fixture allow relamping without having to readjust and
rslock. Follow Steps 7-10 and 13,
NOTE 1. LOW VOLTAGEFIXTURES should be dimmed only with speciai dimmers intended
specifically for that purpose Use Lightolier Lytemodq Soeniat, Crsacendo VA, Neptune VA,
Precision VA, Easyaet VA, Sunrise VA, Radiant VA or equlvalant products by others or variabie
auto-transformera or eiactronic dimmers intendad for use with iow voltage fixtures. 2. Low
voitage fisturas may produce audibie sound whan usad with dlmmere which may be objectionai
in acouaticaiiy criticai areas.
●
WARNING: 1. LAMP MANUFACWRES REQUiRE THE GLASS LAMP GUARD BE IN PLACE BEFORE
Energizing LAMR AND THAT GREAT CARE MUSr BE TAKEN THAT LAMP IS FULLY COOLED
BEFORE RELAMP!NG. AVOID FiNGER MARKS ON INSIDE OF LAMP FOR THEY MAY CAUSE SHORT
LAMP LIFE AND POSSIBLE BREAKAGE.
2. USE 0NL% REFLECIX)R “TRIMS PROViDED BY LiGHTOLIER INC. USE OF Uf’HER
MANUFA~URER’S REFLECTOR TRiMS VOIDS THE UNDERWRITERS LABORA~RIES LiSTING AND
‘COULD Constitute AFIRE HAZARD. J