Lightolier SOF-TECH Instructions for use

Y
READAND UNDERSTANDTHESEINSTRUCTIONS BEFOREINSTALLINGFIXTURE INSTRUCTION SHEET NO.
“hisfixture is intended for installation in accordance with the National Electrical Code and local regulations.
“oassure full compliance with local codes and regulations, check with your local electrical inspector before
mtallation. To prevent electrical shock, turn off electricity at fuse box before proceeding. IS:6273
Retain these instructions for maintenance reference. 1094 Page 1of2
bINSTRUCTIONS FOR ATTACHING SOF-TECH” LOW VOLTAGE TO LYTESPAN” TRACK
FOR USE WITH LYTESPANiTRACK SYSTEMS ONLY
INSTRUCTIONS FOR ATTACHING SOF-TECH” LOW VOLTAGE TO SINGLE CIRCUIT TRACK SYSTEM
1. Insert into LYTESPAN TRACK (see Fig. 1). LOCKING I-EVER must be in same side of track as BEAD.
2. Rotate FllllNG 90” clockwise (see Fig. 2).
3. Rotate FITTING until LOCKING LEVER snaps and locks in place (see Fig. 3).
4. To remove: depress LOCKING LEVER, then rotate FITTING 90” counterclockwise.
~=_=&;_Q/-’’’’’’~~TRACK
r
45 == d
~}1 Fi
.,
‘-%2 Ii-. —_—_–:=.4–,’:,
~;~p,,
-+
~
BEAD —\, ,:\yil .;. -~
—
“i---:- ‘“-
[!
1-””
1
~1.,
J
\,,,—-.
LOCKING .-’
LEVER TO
REMOVE
.,,
FIG.1FIG.3
INSTRUCTIONS FOR CONVERTING SOF-TECH@ LOW VOLTAGE
ATTACHMENT FITTING TO OPERATE ON 2CIRCUIT TRACK
./
BRASS CONTACT
(See Fig. 4) BRASS CONTACT can be raised or lowered. Broken line indicates position >
for 1circuit track system or lower circuit of 2circuit track system.
q-
*L
,,=LOCKING
[1
LEVER
(~’, &:.;=s
To convert attachment FITTING for upper circuit of. 2circuit track, raised BRASS G-
CONTACT to high position by lifting CONTACT as high as stop permits and CONTACT
clicks into place.
SEE BACK FOR LAMPING w—-
FIG.4
Mc> HTcx 1E 1? MONTREAL,QUEBECCANADA
@
FALL RIVER, MASSACHUSETTS, 02720
d
FIG.2

I
INSTRUCTION SHEET NO.
1S:6273 INSTRUCTIONS FOR LAMPING AND
ADJUSTING SOF-TECH@ LOW VOLTAGE
----- _..
1094 Page z orz
1.
2.
3.
4.
Check to see that power is OFF when Iamping or relamping.
For 6273B insert the two I-AMP PINS into the SOCKET HOLES (Fig. 5a);
For 6273T insert the two LAMP STUDS into the SOCKET HOLES and
twist clockwise (Fig. 5b).
Insert COVER with LAMP into RING until (3) LAMP SPRINGS engage
fully with the RING (Fig. 6).
To aim fixture, rotate as shown (Fig. 7)
RING
LAMP GLASS SHIELD
(WITH 6273B ONLY)
t“q-
—
,.
“1“y
C-Eg$il
k
@—
L.. (cc
...[+]-
A. ..g
...—.
&..__&[.-
6———
/<
~T: =>.
--..., -.
,/ ‘“ .<__ /. -1.:=-—
—
~..__ .__-:/’ 1.-—
\:__ LAMP SPRING
——
FIG.6
r
(- ‘-’) SOCKETHOLES
FIG.5a FIG.5b
(6273b) (6273T)
180”
VERTICAL
ROTATION
0“
v“
HORIZONTAL
FIG.7ROTATION
180” d