Lilin Z2R8022EX25 User manual

Part Description & Dimensions
D/N HD AF IR IP CAMERA
66-8022CSB-1B
Installation Guide
372mm
12
16 5
43
2
7
1110
333mm
182mm
116mm
8
9
112mm
ø95
84mm
84mm
13
14
15
17
Top Case
Bottom Case
Lens
Sun Shield
Bottom Box
Top Box
Side Hole
Bottom Hole
Hole Plug
Adjustment Screw A
Adjustment Screw B
Adjustment Screw C
Factory default button
Restores the server back to factory default settings.
Micro SD card slot
Auto Focus button
Live Video Output Connector
LED Indicators
Green (Power): Indicates system status.
Green (Link): Illuminates when the camera is connected to a network
Orange (ACT): Flashes when data communication is in process.
1
2
3
4
5
6
7
8
9
10
11
12
16
13
14
15
16
17
The IP camera will automatically adjusts the camera lens to obtain focus after
press the AF (Auto Focus) button continuously for 2 seconds. User can adjust
the image view by using zoom in/out button via web access, and refocus using
the Auto-Focus link on the main Web page.
Installation
1. Retrieve the camera and remove the bottom box from the top box with a hex
key (FIG.1), and remove the safety cable on the bottom box (FIG.2). Use the
included screws (M4.0x25) through the holes marked as “a”, and fix the
camera in the desired location(FIG.3&4).
a a
a a
FIG.1 FIG.2
FIG.3 FIG.4
2. Firstly, insert the network cable and power cable through a pipe with ½" PT,
and then secure the pipe to the side hole or bottom hole (FIG.5. please make
sure the connection between the pipe and the side hole is watertight, and the
side hole is facing downwards).
To prevent the camera from falling, you should secure the safety cable(FIG.6).
FIG.5
DC12V
GND
—
N.O.
COM.
DIN
GND
AIN
GND
AOUT
—485
＋485
3. Connect the network cable and power cable to the camera’s RJ-45 connector
and power input, respectively (FIG.7). Secure the top box to the bottom box
(FIG.8).
+12V IN
GND
–
N.O.
COM.
DIN
GND
AIN
GND
AOUT
–485
+485
FIG.7 FIG.8
FIG.6
4. Adjust the three adjustment screws to move the camera to the desired angle,
and then tighten the adjustment screws (FIG.9~12).
FIG.9 FIG.10
FIG.11 FIG.12
Change the Outlet Position for the Network Cable and Power Cable
1. Loosen the hole plug on the bottom box and secure it to the side hole (FIG.13).
2.Insert the network cable and power cable through bottom hole on the bottom
box (FIG.14), and then connect the network cable and power cable to the
camera’s RJ-45 connector and power input, respectively (FIG.7). For
watertight installation, please refer to Installation-2.
FIG.13 FIG.14
For connecting IP Camera series to the network, please follow one of the
system architectures:
(1). Use DC12V power adaptor and network switch connected to a network.
System Architectures
PoE Switch
PC
LAN LAN / Internet
PC
LAN LAN / Internet
Non-PoE Switch
DC12V Adaptor
(2). Use with PoE of the network switch connected to the network.
IP CAMERA
(3). Use PoE power injector and the network switch connected to the network.
PoE Power Injector
PC
LAN LAN / Internet
AC
Non-PoE Switch
LAN
IP CAMERA
IP CAMERA
To restore the hardware to factory default settings, please follow these steps:
1.Press and hold “RESET Key” for 10 seconds and release.
2.Wait for about 40 seconds, and the network LED light should turn off, and
go back on again.
3.The camera is now restored to factory default settings, and will reboot
automatically.
4.Search for the IP device using the IPScan software.
5.Start the IP device via an Internet browser.
6.Enter the username and password to operate.
The factory default username and password are empty, and the
user can set an account for login.
The IP address will revert to the default setting of 192.168.0.200.
NOTE1:
NOTE2:
Emergency Factory Default
To change an IP address via web interface, type the default IP address
(192.168.0.200) in the Internet browser and follow the steps below:
1. Login to the Full HD IP camera with the set username and password.
2. Click Basic Mode configuration hyperlink.
3. Click Network->General hyperlink.
4. Change the IP address, subnet mask, gateway, or HTTP port for the IP
camera.
5. Click Submit to verify the settings.
Configuring IP Addresses via Web Interface
Before accessing the IP camera, make sure that the camera's RJ-45
network, audio, and power cables are properly connected. To set the IP
address, consult your network administrator for an available IP address.
The default IP address for each IP camera is 192.168.0.200. Users can use
the default IP address for verifying the camera's network connection.
Before Accessing IP Cameras
To change the settings of the IP address, subnet mask, gateway, or HTTP
port, you can follow the steps below:
1. Run the IPScan software.
2. Click Refresh. All available devices should be listed in the device list.
3. Select your device from the list provided.
4. Change the IP address, subnet mask, gateway, or HTTP port for the IP
camera.
5. Click Apply to submit the settings.
6. Click Refresh to verify the settings.
Configuring IP Addresses with IPScan Software
Universal ActiveX software components are required for web interface
display of JPEG or Full HD video. When you login to the IP camera by
Internet Explorer, the security warning dialog box will prompt the
installation of the Universal ActiveX. Click Install to download it.
Software Requirements
Login
The factory default username and password are empty. To login to the Full
HD IP camera, please set the username and password on the login page.
Press [Login] to complete the setting and login simultaneously.
Password have to meet the following
criteria:
1. More than or equal to 8 characters.
2. Allow uppercase letter, lowercase letter,
number digit, and special character.
3. Must have at least three types of
character sets.
IPCAM

日夜兩用高畫質自動變焦紅外線
網路攝影機
警語: 此圖示，指在廢棄產品時不可直接丟棄垃
圾桶，應進行拆解，並分類進行回收再利用。
部件說明及尺寸
安裝說明
372mm
12
16 5
43
2
7
1110
333mm
182mm
116mm
8
9
112mm
ø95
84mm
84mm
13
14
15
17
16
13
14
15
16
17
上蓋
下蓋
鏡頭
遮陽罩
接線盒底座
接線盒上蓋
側孔
底孔
孔塞
調整螺絲 A
調整螺絲 B
調整螺絲 C
回復工廠預設值按鍵
Micro SD卡插槽
AF 自動對焦按鍵
按下自動對焦（AF）鍵 2秒鐘。網路攝影機會
執行自動對焦功能。也可以從網頁的操作介面
調整鏡頭的焦距、放大倍數到所需的成像畫面。
影像輸出連接座
指示燈
綠色（POWER燈號）：系統狀態顯示
綠色（LINK燈號）：網路線接上時，此LED恆亮。
橙色（ACT燈號）：資料通訊時，此LED閃爍。
1
2
3
4
5
6
7
8
9
10
11
12
安 裝
1.
（圖1）；再將底座上的安全索拆下（圖2）。
接著再取出所附的螺絲（M4.0x25），經由標示為 "a" 的螺絲孔
，將接線盒底座固定在所需的位置上。
首先取出網路攝影機，使用六角板手將接線盒底座與上蓋分開
a a
a a
圖 1圖 2
圖 3圖 4
2. 首先把網路電纜線和電源線穿過1/2" PT管子，再將管子旋入底座
的側孔或底孔（圖5，管子與側孔兩者之間的結合，必須是防水的
；同時側孔也必須在下方）。接著再將安全索鎖回接線盒底座上
，避免掉落（圖6）。
圖 5
DC12V
GND
—
N.O.
COM.
DIN
GND
AIN
GND
AOUT
—485
＋485
+12V IN
GND
–
N.O.
COM.
DIN
GND
AIN
GND
AOUT
–485
+485
圖 7圖 8
圖 6
3
端（圖7）；接著再將接線盒上蓋鎖回底座（圖8）。
. 將網路電纜線和電源線接上攝影機的RJ-45網路插座及電源輸入
圖 9圖 10
4
影角度後，再將其調整螺絲鎖緊 9
. 依需求調整腳架上的三個調整螺絲，轉動攝影機主體到所需的攝
（圖 ~12）。
圖 11 圖 12
圖 13 圖 14
變更網路電纜線和電源線的出線位置
1. 轉鬆取下接線盒底座的孔塞，再將其鎖緊在側孔上，（
其連接到攝影機的R J-45網路插座及電源輸入端（圖7）。防水安
裝請參閱第2項的說明。
圖13）。
2. 把網路電纜線和電源線穿過接線盒底座的底孔（圖14），然後將
請依據下列其中一種系統架構，連結高畫質網路攝影機和您的網
路。
(1). 使用DC12V電源變壓器和網路交換器連接網路。
系統架構
PoE Switch
PC
LAN LAN / Internet
(2). 使用配備 PoE 的網路交換器連接網路。
PC
LAN LAN / Internet
Non-PoE Switch
DC12V Adaptor
(3). 使用 PoE 供電裝置 (Power Injector) 和網路交換器連接網路。
PoE Power Injector
PC
LAN LAN / Internet
AC
Non-PoE Switch
LAN
IP CAMERA
IP CAMERA
IP CAMERA
在使用 Full HD IP攝影機之前，請先確認攝影機RJ-45網路接頭和
電源接頭是否接妥，並請網管人員提供一組未經使用的IP位址。
出廠預設IP位址為192.168.0.200，使用者可以先行使用該IP位址去
更改相關網路設定。
安裝前準備
使用硬體來回復出廠預設值，請按照下列步驟：
1. 按住「回復出廠預設值按鍵」10 秒鐘。
2. 約40秒鐘後網路連接 LED 燈將熄滅再點亮。
3. 網路伺服器將重新開機。
4. 使用 IPScan 軟體搜尋此 IP 設備。
5. 使用網路瀏覽器開啟此 IP 設備。
6. 輸入預設使用者名稱及密碼進行操作。
出廠預設的使用者名稱和密碼為空白，由使用者自行設定
輸入。
為方便使用者起見，回復出廠預設值會回復到預設 IP 位址
192.168.0.200。
註1：
註2：
回復出廠預設值
您可以
IP位址、子網路遮罩、網路閘道、或HTTP連接埠，請參照下列步
驟：
1. 執行IPScan軟體工具
2. 按「更新表單」鍵，區域網路內的所有設備將顯示在設備清單
欄位
3. 用滑鼠點選該設備
4. 編輯或修改該設備之IP位址、子網路遮罩、網路閘道(Gateway)
或HTTP連接埠等欄位
5. 按「套用」鍵來更改該設定
6. 按「更新表單」鍵來驗証該設定
使用IPScan(網路設備搜尋軟體)工具來設定IP位址。要更改
使用 軟體工具來設定 位址IPScan IP
登 入
出廠預設的使用者名稱和密碼為空白。 入Full HD 網路攝影機
，請在登入頁面，設定使用者名稱及密碼並按下確認鍵，可同時
完成使用者設定並登入。
欲登
1 8
2
3 3
密碼強度要求：
. 密碼長度需要 個字以上。
. 密碼必須包含英文字大寫、小寫、
數字及特殊符號。
. 密碼必須強制使用至少 種文字型
態。
IPCAM
請先在網路瀏覽器網址列，輸入預設IP位址192.168.0.200。並按
照下列步驟執行，使用HTML頁面來更改IP位址：
1. 設定使用者名稱及密碼，登錄 Full HD IP攝影機
2. 按「組態設定」超連結
3. 按「網路設定」「一般設定」超連結
4. 輸入或修改IP位址、子網路遮罩、網路閘道(Gateway)或HTTP連
接埠
5. 按「確認」鍵，完成上述修改
Full HD 網路攝影機需要軟體解壓縮器顯示影像，Full HD 網路攝影
機的網頁介面需使用該軟體。 當您第一次登錄本產品，Full HD
網路攝影機的網頁介面會自動安裝Universal ActiveX元件，請按下
「安裝」鍵安裝該元件。
軟體需求
使用 頁面來設定 位址HTML IP