Lilin Z2R8122X-P User manual

Change the Outlet Position for the Ethernet and Power Cables
Loosen the threaded plug at the bottom of the junction box and secure it to the lateral
hole (FIG.19).
2. Insert the Ethernet cable, video cable, and power cable through the opening at the
bottom of the junction box (FIG.20) and connect them to the camera's RJ-45 connector,
video output, and power input respectively (refer to “1” for more instructions on wiring).
1.
Installation Guide
Part Description & Dimensions
D/N HD (AF) IR IP CAMERA
Camera Body
Window
Adjustment Screw A
Adjustment Screw B
Adjustment Screw C
Lens
LED Indicators
Green (Power): indicates system status.
Green (LINK): Illuminates when the camera is connected to a network.
Orange (ACT): Flashes when data communication is in process.
Unit: mm
1
2
3
4
5
6
7
8
9
10
Installation
The IP camera will automatically adjusts the camera lens to obtain focus after pressing the AF
(Auto Focus) button continuously for 2 seconds. User can adjust the image view by using zoom
in/out button via web access, and refocus using the Auto-Focus link on the main Web page.
Connect the RJ-45 Ethernet cable with a waterproof connector
First, remove the waterproof connector and unscrew the waterproof nut. Insert the Ethernet
cable and connect to the RJ-45 connector with proper tools (FIG.3). Then, tighten the
waterproof connector and nut before the RJ-45 connector is connected to the camera (FIG.4).
FIG.3 FIG.4
Install the Camera with a Junction Box (Optional)
A. Choose a desired position for the junction box, and secure the truss head screws enclosed
in the box to the holes marked as “a” (FIG.11 & 12) on the junction box.
66-8122OOE-1
2
1
6
3
102.5
102.5
84
78
257.8
239.8
135
209.8
105
227.8
[HD AF IR IP Camera] [HD IR IP Camera]
1
3
9
8
7
11
2
55
10
44
11
Live Video Output
Reset Key
Restores the camera back to factory default settings.
Micro SD Card Slot
AF Key [Auto Focus Model Only]
1. Remove the camera from the Box. Connect the Ethernet cable, video cable, and power cable to
the camera's RJ-45 network connector, video output connector respectively, and DC power-in
connector (FIG.1). Secure the camera to the wall (FIG.2).
FIG.1 FIG.2
Video output wire
Network Cable
DC Power Input
DC12V +
DC12V -
Audio OUT
GND
Audio IN
GND
Alarm IN
COM
Alarm OUT
DC12V
AUDIO
ALARM
2. Loosen the three adjustment screws on the bracket to change the camera direction according
to different needs before according to different needs.
Be sure to tighten the screws after the adjustment is completed (FIG.5–10).
FIG.5 FIG.6
FIG.7 FIG.8
FIG.9 FIG.10
FIG.11 FIG.12
a a
a a
B. Insert the Ethernet cable, video cable, and power cable through the 1/2”PT tube (FIG.13),
and rotate to secure the tube to the holes on the lateral or bottom of the junction box
(FIG.14). The conjuction between the tube and the hole must be airtight, and the opening
of the hole must point downward.
FIG.13 FIG.14
C. Attach the safety cable to the hole at the bottom of the junction box (FIG.15), and connect
the Ethernet cable, video cable, and power cable to the camera's RJ-45 connector, video
output, and power input respectively (FIG.16). Please refer to “1.” For more wiring
instructions.
FIG.16FIG.15
Video output wire
Network Cable
DC Power Input
C. Use the screws (M5.0x12L) included in the box to secure the camera to the junction box,
and tighten the screws (FIG.17&18).
FIG.17 FIG.18
FIG.19 FIG.20

For connecting D/N 1080P HD IP Camera series to the network, please follow one
of the system architectures:
(1). Use DC12V power adaptor and network switch connected to a network.
System Architectures
PoE Switch
LAN LAN / Internet
PC
LAN LAN / Internet
Non-PoE Switch
DC12V Adaptor
(2). Use with PoE of the network switch connected to the network.
HD IP CAMERA
PC
(3). Use PoE power injector and the network switch connected to the network.
PoE Power Injector
PC
LAN LAN / Internet
AC
Non-PoE Switch
LAN
HD IP CAMERA
HD IP CAMERA
Before accessing the IP camera, make sure that the camera's RJ-45 network,
audio, and power cables are properly connected. To set the IP address, consult
your network administrator for an available IP address. The default IP address for
each IP camera is 192.168.0.200. Users can use the default IP address for
verifying the camera's network connection.
Before Accessing IP Cameras
Universal ActiveX software components are required for web interface display of
JPEG or Full HD video. When you login to the IP camera by Internet Explorer, the
security warning dialog box will prompt the installation of the Universal ActiveX.
Click Install to download it.
Software Requirements
To configure an IP address using the IP scan tool, you can copy the IPScan software
from the installation CD, and paste to your computer. Alternatively, you can execute
the IPScan software from the installation CD. To change the settings of the IP
address, subnet mask, gateway, or HTTP port, you can follow the steps below:
1. Run the IPScan software.
2. Click Refresh. All available devices should be listed in the device list.
3. Select your device from the list provided.
Configuring IP Addresses with IPScan Software
To restore the hardware to factory default settings, please follow these steps:
1. Press and hold “RESET Key” for 10 seconds and release.
2. Wait for about 40 seconds, and the network LED light should turn off, and go
back on again.
3. The camera is now restored to factory default settings, and will reboot
automatically.
4. Search for the IP device using the IPScan software.
5. Start the IP device via an Internet browser.
6. Enter the default username “admin” and password “pass” to operate.
For your convenience, the IP address will revert to the default setting
of 192.168.0.200.
NOTE:
Emergency Factory Default
4. Change the IP address, subnet mask, gateway, or HTTP port for the IP camera.
5. Click Apply to submit the settings.
6. Click Refresh to verify the settings.
To change an IP address via web interface, type the default IP address
(192.168.0.200) in the Internet browser and follow the steps below:
1. Login to the Full HD IP camera by the default username “admin” and default
password “pass”.
2. Click Basic Mode configuration hyperlink.
3. Click Network->General hyperlink.
4. Change the IP address, subnet mask, gateway, or HTTP port for the IP camera.
5. Click Submit to verify the settings.
Configuring IP Addresses via Web Interface
Make sure your Internet browser allows the signed ActiveX plug-in to work on
your computer. Set “Download Signed ActiveX plug-in controls” to “Prompt” and
“Run ActiveX control and plug-in” to “Enable”. You can set this option via Internet
Explorer-> Tools-> Options-> Security Settings.
Internet Browser Settings & Application Required
Once complete, you can access the IP camera's live video by entering the default
IP address via your Internet browser. As the security warning dialog box appears,
click OK to download the ActiveX directly from the IP camera.
To logon the FULL HD IP camera, please type username and password in logon
HTML page and click on Submit button to enter the system.
Login
The default usernames and passwords are as follows:
Username admin
Password pass
Administrator