Linak DPA User manual

Page 1 of 44
To learn more about LINAK, please visit:
www.linak.com
USER MANUAL
Controls/Handsets

Page 2 of 44

Page 3 of 44
Contents
Preface..................................................................................................................................................4
Safety instructions..............................................................................................................................5
Repairs..................................................................................................................................................7
Manufacturer’s declaration................................................................................................................7
Misc. on the DESKLINE®system ........................................................................................................8
Warranty..........................................................................................................................................8
Maintenance....................................................................................................................................8
ETL-marking.........................................................................................................................................8
Overview of the DESKLINE Controls product range ....................................................................10
Mounting guidelines for DPA/DPB .................................................................................................11
Mounting guidelines for DPH .........................................................................................................11
Operation of the DP1........................................................................................................................11
Operation of the simple desk panels .............................................................................................12
Operation of the DP1C .....................................................................................................................13
Operation of the DP1CS...................................................................................................................15
Remote control HB10RF / HB20IR...................................................................................................17
Activating the learning mode ......................................................................................................... 18
Operation of the DPF........................................................................................................................19
K-version .......................................................................................................................................19
2K- and 3K-version ........................................................................................................................19
M-version ......................................................................................................................................19
Operation of the DPF1C “one reference”......................................................................................20
Operation of the DPF1D...................................................................................................................21
Operation of the DPF4T “multiple references”.............................................................................22
Other functions common for DPF1C and DPF4T.............................................................................. 23
Mounting of all DPF versions ..........................................................................................................24
Drawings of the mounting brackets ................................................................................................25
Operation of the DPT........................................................................................................................26
Mounting of the DPT ........................................................................................................................ 28
Operation of the WDPL.....................................................................................................................29
Calibrating the WDPL.....................................................................................................................30
Adjusting the clock ........................................................................................................................31
Troubleshooting.............................................................................................................................31
Store a memory position ................................................................................................................ 32
Switch to a stored memory position................................................................................................33
Disposal of LINAK’s products .........................................................................................................34
Disposal of batteries ........................................................................................................................ 34
Labels ................................................................................................................................................35
Drawing appendix.............................................................................................................................36
Addresses........................................................................................................................................... 44

Page 4 of 44
Preface
Dear User,
We are delighted that you have chosen a product from LINAK®.
LINAK systems are high-tech products based on many years of experience in the manufacture and development of
actuators, electric control boxes, controls and chargers.
This User Manual does not address the end-user. It is intended as a source of information for the manufacturer
of the equipment or system only, and it will tell you how to install, use and maintain your LINAK electronics. It
is the responsibility of the manufacturer of the end-use product to provide a User Manual where relevant safety
information from this manual is passed on to the end-user.
We are sure that your LINAK product will give you many years of problem-free operation.
Before our products leave the factory they undergo full function and quality testing. Should you nevertheless
experience problems with your systems, you are always welcome to contact your local dealer.
LINAK subsidiaries and some distributors situated all over the world have authorised service centres, which are
always ready to help you.
LINAK provides a warranty on all its products. This warranty, however, is subject to correct use in accordance with
the specifications, maintenance being done correctly and any repairs being carried out at a service centre, which is
authorised to repair LINAK products.
Changes in installation and use of LINAK systems can affect their operation and durability. The products are not to
be opened by unauthorised personnel.
The User Manual has been written based on of our present technical knowledge. We are constantly working on
updating the information and we therefore reserve the right to carry out technical modifications.
LINAK A/S

Page 5 of 44
Safety instruction
General
Important information
Important information on LINAK®products can be found under the following
headings:
Warning!
Failure to comply with these instructions may result in accidents involving
serious personal injury.
Failing to follow these instructions can result in the product being damaged
or being destroyed.
Safe use of the system is possible only when the operating instructions are read
completely and the instructions contained are strictly observed.
Failure to comply with instructions marked with the ”NOTE” symbol may result in
serious damage to the system or one of its components.
It is important for everyone who is to connect, install, or use the systems to
have the necessary information and access to this User Manual. Follow the
instructions for mounting – risk of injury if these instructions are not followed.
The appliance is not intended for use by young children or infirm persons
without supervision.
If there is visible damage on the product it must not be installed.
Note that during construction of applications, in which the actuator is to
be fitted, there must be no possibility of personal injury, for example the
squeezing of fingers or arms.
Assure free space for movement of application in both directions to avoid
blockade.

Page 6 of 44
Only for EU markets
This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved.
Children shall not play with the appliance. Cleaning and user maintenance
shall not be made by children without supervision.
Only for Non EU markets
Persons who do not have the necessary experience or knowledge of the
product/products must not use the product/products. Besides, persons with
reduced physical, sensory or mental abilities must not use the product/products,
unless they are under surveillance or they have been thoroughly instructed in
the use of the apparatus by a person who is responsible for the safety of these
persons.
Moreover, children must be under surveillance to ensure that they do not
play with the product.
Misuse
Do not overload the actuators – this can cause danger of personal injury and
damage to the system.
Do not use the actuator system for lifting persons. Do not sit or stand on a
table while operating – risk of personal injury.
Do not use the system in environments other than the intended indoor use

Page 7 of 44
Repairs
In order to avoid the risk of malfunction, all DESKLINE®repairs must only be carried out by authorised LINAK®workshops or
repairers, as special tools must be used and special gaskets must be fitted. Lifting units under warranty must also be returned
to authorised LINAK workshops.
Warning!
If any of the DESKLINE®products are opened, there will be a risk of subsequent malfunction.
Warning!
The DESKLINE®systems are not resistant to cutting oil.

Page 8 of 44
Misc. on the DESKLINE®system
Warranty - 60 months on DESKLINE®(NEW)
This will be valid for all DESKLINE®products produced after the 1st of May 2015.
Products produced before 1st of May 2015 will still be covered by 36 months.
Products used in DESKLINE application: If these products are used in another application, they will be covered by 18 months
warranty.
If there is any doubt that returned products are within the warranty period it is to be treated as if they are covered by the
warranty. We recommend that you use the date of the Control box or actuator as reference if possible. We will have our
purchase no. printed on the label.
Maintenance
Clean dust and dirt on the outside of the system at appropriate intervals and inspect for damage and breaks.
Inspect the connections, cables, and plugs and check for correct functioning as well as fixing points.
The cleaners and disinfectants must not be highly alkaline or acidic (pH value 6-8).
ETL-marking
Due to space limitations, the complete ETL-marking demands are not represented on the marking plates.
The full ETL Recognized Component markings are shown here.
C/N 120690
Conforms to ANSI/AAMI Std. ES60601-1
Cert. to CSA Std. C22.2 No. 60601-1
ETL Recognized Component mark for Canada and United States
C/N 4008003
Conforms to ANSI/AAMI Std. ES60601-1
Cert. to CSA Std. C22.2 No. 60601-1
ETL Recognized Component mark for Canada and United States
C/N 4008004
Conforms to ANSI/AAMI Std. ES60601-1
Cert. to CSA Std. C22.2 No. 60601-1
ETL Recognized Component mark for Canada and United States
C/N 4008005
Conforms to ANSI/AAMI Std. ES60601-1
Cert. to CSA Std. C22.2 No. 60601-1
ETL Recognized Component mark for Canada and United States
C/N 4008623
Conforms to ANSI/AAMI Std. ES60601-1
Cert. to CSA Std. C22.2 No. 60601-1
ETL Recognized Component mark for Canada and United States

Page 9 of 44
C/N 4008671
Conforms to UL962
Cert. to CSA Std. C22.2 No. 68-09
ETL Recognized Component mark for Canada and United States
C/N 4008838
Conforms to ANSI/AAMI Std. ES60601-1
Cert. to CSA Std. C22.2 No. 60601-1
ETL Recognized Component mark for Canada and United States
C/N 4009507
Conforms to UL962
Cert. to CSA Std. C22.2 No. 68-09
ETL Recognized Component mark for Canada and United States
C/N 9901916
Conforms to ANSI/AAMI Std. ES60601-1
Cert. to CSA Std. C22.2 No. 60601-1
ETL Recognized Component mark for Canada and United States

Page 10 of 44
Overview of the DESKLINE Controls product range
The desk panel is used to operate the DESKLINE system. The desk panel product range consists of number of desk panels with
different functions:
For single/parallel drive without memory: DPA, DPB, DP1K, DP1V, DPF1K, DPH and DPF1D
For drive of more references: DPF4T, DPF2K and DPF3K
DPF2K - Desk Panel DPF3K - Desk Panel
DPF4T - Desk Panel
For single/parallel drive with memory: DP1N, DP1U, DP1CS, DPF1C, DPF1M and DPT
DP1U - Desk Panel
2
1
3
S
2
1
U
S
DP1N - Desk Panel DP1CS - Desk Panel
DPF1M - Desk Panel
DPF1C - Desk Panel DPT
DPA - Desk Panel DP1K - Desk Panel
DPB - Desk Panel
DP1V - Desk Panel
DP-025
DPH - Desk PanelDPF1K - Desk Panel
DPF1D - Desk Panel

Page 11 of 44
Mounting guidelines for DPA/DPB
The DPA/DPB can be mounted on the desktop so that the keys are either facing upwards or outwards. Alternatively the DPA
can be mounted flat under the desktop with the keys facing downwards.
Operation of the DPA/DPB in connection with DESKLINE®systems (not CBD2N)
The Desk Panel is used to operate the DESKLINE system. The two arrow buttons are used for parallel drive.
Parallel drive ( )
The arrow buttons start parallel drive. The function is only activated when holding the button down.
The mounting screws on the DP, DPA, or DPB must be fastened with a max. torque of 1 Nm.
Mounting guidelines for DPH
The hole in the tabletop must be in accordance with this drawing.

Page 12 of 44
Desk up
Desk down
Store memory
User memory
Memory 1
Memory 2
Memory 3
Operation of the simple desk panels
Here you find the guide on how to operate the DPA, DPB, DP1K, DP1N, DP1U, DP1V, DPH and DP1CS
Single/parallel drive
The arrow buttons start the DESKLINE lifting column.
The function is only activated when holding down the button.
S
U
1
2
3
DP1U - Desk Panel
2
1
3
S
DPA - Desk Panel
DP1K - Desk Panel
DPB - Desk Panel
DP1V - Desk Panel
DP-025
2
1
U
S
DP1N - Desk Panel
DPH - Desk Panel
Store memory
Push
Within two sec. push either , or
123
S
S
Choice of user (only DP1N)
Two persons can store 2 memory positions each.
Select user 1 or user 2.
Push
Within two sec. push either or
Store memory
Push
Within two sec. push either or
S
U
U
1 2
S
12
Memory drive
Memory 1, 2, and 3 start a memory drive, the channel(s)
drive to a preprogrammed position.
1 2 3
DP1CS - Desk Panel

Page 13 of 44
Description
The DP1C is equipped with display and memory and is compatible with CBD4 (Advanced, software 077402 ver. 1.66 or later).
The DP1 is only available as a 1-channel version for operation of the parallel channels up and down. The actual height of the
desk is shown in the display. The display is of the LED type with a yellow light and 10 mm high digits.
Normal operation:
To run the desk up or down, press the UP or DOWN button, and keep it pressed until the desk reaches the desired height. The
display will count up or down while running, and after stop it will continually show the current height of the desk.
Changing between cm and inches:
Keep the S button pressed for approx. 4 sec. and the reading will change from the current setting.
The default setting depends on the type chosen.
Store a memory position:
When pressing the “store” button, the display will flash “S” for 3 sec. Within the 3 sec. press memory button 1, 2 or 3. The
display will acknowledge by showing S1, S2 or S3 for 1 sec. To abort a store sequence, press the UP or DOWN button while
the “S” is flashing, or wait the 3 sec. until the display automatically returns to show the height of the desk.
Drive to a stored position:
Version with “GO-memory”
Press memory button 1, 2, or 3. The display will flash “GO1”, “GO2” or “GO3” for 3 sec. Within the 3 sec. press the UP or
DOWN button and keep it pressed until the desk stops in the stored position. Both the Up and the Down button will activate
memory drive. Although e.g. the memory position is higher than the actual height, it will drive upwards when you press the
Down button. While running to a memory position the display will show GO1, GO2 or GO3, and when it stops in the stored
position, the height of the desk will be shown. Releasing the UP or DOWN button will abort the memory drive. The display will
show the height of the desk.
Version with “standard memory”
Press memory button 1, 2, or 3 and the system will start driving to the wanted memory position. Keep the button pressed until
the position is reached. The display will show the actual height during the memory run.
Adjust the display to show the correct height:
It may be necessary to adjust the display due to different thicknesses of desktops etc, when the DP is delivered from the
factory. The DP will show 68 cm or 24.5 inches (default setting) height of the desk. At the same time press the “Store” button
and step UP or DOWN, until the display shows the correct height.
Adjusting the light intensity of the LED display
Possible light settings are: 0 = off, 25 = 25%, 50 = 50%, 75 = 75%, 100 = 100%.
Adjustment procedure
Press the “1” button and at the same time either “desk up” or “desk down” this will adjust the light intensity. Initial press will
show the current setting. Keep the “1” button pressed during the whole sequence while adjusting up or down. Keep a button
pressed for more than 800 msec then the button will auto repeat every 100 msec. Releasing all buttons stores the new setting.
Adjusting the light timeout
Possible light timeouts are: 0-15 sec and off
Adjustment procedure
Press the “3” button and at the same time either “desk up” or “desk down” - this will adjust the light timeout. Initial press
Operation of the DP1C
The DP1C cannot be used on the CBD4 with mains cut-off.
Desk up
Desk down
Store memory
Memory 1
Memory 2
Memory 3
S
1
2
3

Page 14 of 44
Error no. Description
E01 The desk has an unknown position and needs to be initialised.
E02 Overload upwards has occurred.
E03 Overload downwards has occurred.
E16 Illegal keys pressed.
will show the current setting. Keep the “3” button pressed during the whole sequence while adjusting up or down. Keep a
button pressed for more than 800 msec, then the button will auto repeat every 100 msec. Releasing all buttons stores the new
setting.
Errors
Below please find the possible errors that can be displayed. The errors will only be displayed when a button is pressed. The
display blinks while showing the error. E16 overrules any other error as the detection is registered only in the display and no
message is sent to the control box.
Diagnostic errors
The CBD4 (version 1.86 or later) can send up to 6 different diagnostic error codes at the same time.
The diagnostic error codes will overrule error states (except E16). Diagnostic errors will only appear as long as the button is
pressed. The display will blink EXX and will toggle through the diagnostic errors and send them to the LINBUS in the CBD. For
detailed error description and codes, please see the appropriate CBD software description.
(Only working with DP1C from production date 1 february 2006 and onwards)

Page 15 of 44
Description
The DP1CS is equipped with display and memory and is compatible with DESKLINE control boxes. The DP1CS is available as a
1-channel version for operation of the parallel channels up and down. The actual height of the desk is shown in the display.
The display is of the LED type with a yellow light and 10 mm high digits.
Up and down (^V):
You just either have to activate the up or down button for parallel drive and the system will drive until releasing the button
again or when the system reaches end position.
Memory:
The four small buttons are used for memory drive/storing memory.
Store memory
• Press S – button, the display will flash “S” for 2 seconds
• Within these two seconds press one of the small buttons with numbers “1”, “2” or “3” and the position
will be stored at this button.
• The panel will acknowledge by showing “1”, “2” or “3” in the display depending on the chosen position
Memory drive
Press one of the memory buttons and the system will start driving to the pre-programmed memory position. Keep the button
pressed until the position is reached.
Display function
Shows the actual height in either cm or inch and can display error codes.
Operation of the DP1CS
Parallel up
Parallel down
Memory 1
Memory 2
Memory 3
Store memory
S
1
2
3

Page 16 of 44
Error no. Description
E01 The desk has an unknown position and needs to be initialised.
E02 Overload in upward direction has occurred.
E03 Overload in downward direction has occurred
E16 Illegal keys are pressed.
Other functions:
Adjusting initial height:
It may be necessary to adjust the displayed height due to different thicknesses of desktops etc. The DP1CS will as standard
show either 68cm or 24.5 inch as the default desk height.
Procedure:
Press /\ and \/ keys at the same time and keep them pressed for 5 seconds. This allows the initial height to be adjusted. Until
the initial height can be adjusted, the display will show three minuses (---) - hereafter the display will revert to showing the
height. The height can then be adjusted by either /\ or \/ until the desired height has been reached. The system will return to
normal operation (and give a short blink) after 5 seconds of inactivity on the keys.
The feature can be disabled via configuration in which case pressing the /\ and \/ keys at the same time will be considered an
illegal keypress.
Switch between cm and inch:
Switching between cm and inch can only be done via the DPF configurator
Adjusting the light intensity of the LED display:
Possible settings are Off, 6%, 12%, 19%, 25%, 37%, 50%, 75% and 100%.
The adjustment can only be done via the DPF configurator.
Adjusting the light timeout:
Possible settings are 0-15 seconds and Off.
The adjustment can only be done via the DPF configurator.
Error codes
Below please find the possible error codes that can be displayed. The error codes will only be displayed when a button is
pressed. The display will blink while showing the error code. The E16 error will overrule any other errors as the detection is
registered only in the display and no message is send to the control box.

Page 17 of 44
Position of the internal e
y
eConnector for extension eye
Remote control HB10RF / HB20IR
Operation of the system:
The HB21 IR transmitter is a simple up/down control with a button for the up
activation and a button for the down activation of 1 reference on the CBD.
The HB22 is a two-channel controller, for controlling two references on the CBD.
For activation of the control box point with the HB20 at the DP1V or the extension eye: Press the button up or down.
The operation range for the HB20 is approx. 6 m.
Drawings:
DP1V
IR extension eye article number 0964571
The IR extension eye is for mounting in a 12 mm hole. The eye has a 2000 mm cable with a mini Jack plug, which is to be
plugged into the DP1V.

Page 18 of 44
Activating the learning mode:
Activate the reset key on the RFR by using a pen or similar to keep the button pressed.
• Keeping the reset key activated; the RF handset must be activated by pressing a random key on the RF handset.
The RF handset IDs are stored in the memory and at the same time, previous RF handset IDs are erased.
• After having activated the RF handset keys the reset key must be released.
• If no RF handset keys are activated during the matching procedure; no changes are made in the ID memory.
• Please be aware that other equipments (as e.g. doorbells), which use the 433 MHz can disturb the RF signal.
Every RF handset has its own 32 bit unique address and the RF protocol contains a check sum which ensures that only
the handset that has been activated during the learning process can activate the system. No noise signal from other RF
equipment can activate the system, but might prevent it from running depending on the signal strength of the noise signal.
The operation range for the HB10 is approx. 6 m, but depending on the surroundings where it is mounted it can be less. E.g.
if the receiver is mounted in a cabinet along with other equipment.
To avoid signals getting disturbed, do not use more than two RFRL boxes in one room.
The RF uses the frequency 433 MHz
How to place the RFRL box
The RFRL box must be mounted minimum 30 cm from the CBD and conductive mains cables.
Correct placement Wrong placements
Min. 30 cm

Page 19 of 44
Operation of the DPF
= Parallel up
V = Parallel down
S = Store memory
• = Memory 1
•• = Memory 2
••• = Memory 3
Parallel drive ( V)
The arrow buttons start parallel drive. The function is only activated when holding the button down.
Store memory
• Press S – button
• Within two seconds press one of the small buttons with dots and the position will be stored at this button.
Memory drive (small buttons with dots)
Press one of the memory buttons and the system will start driving to the pre-programed memory position.
Keep the button pressed until the position is reached.
DPF1K - Desk Panel
DPF1M - Desk Panel
K-version:
Just activate either the up or down button for parallel drive and the system will
drive until the button is released again or the system reaches end position.
2K-version:
Just activate either the up or down button and the system will drive until the
button is released again or the system reaches end position. Each set of up/down
buttons refers to a reference. You can only drive one reference at a time. The desk
panel can have up to 2 references.
3K-version:
Just activate either the up or down button and the system will drive until the
button is released again or the system reaches end position. Each set of up/down
buttons refers to a reference. You can only drive one reference at a time. The desk
panel can have up to 3 references.
M-version:
The DPF is divided into parallel and memory drive. The two arrow buttons are
used for parallel drive and the last four buttons for memory drive/storing memory.
V
V
DPF2K - Desk Panel
DPF3K - Desk Panel

Page 20 of 44
DPF1C - Desk Panel
Operation of the DPF1C “one reference”
Up and down ( V):
Just activate either the up or down button for parallel drive and the system will drive until the button is released again or the
system reaches end position.
Memory:
The four small buttons are used for memory drive/storing memory.
Store memory
• Press S – button, the display will flash for 2 seconds
• Within these two seconds press one of the small buttons with dots and the position will be stored at this button.
• The panel will acknowledge by showing “1”, “2” or “3” in the display depending on chosen position
Memory drive (small buttons with dots)
Press one of the memory buttons and the system will start driving to the pre-programmed memory position.
Keep the button pressed until the position is reached.
Display function
Shows the actual height in either cm or inch.
= Parallel up
V = Parallel down
S = Store memory
• = Memory 1
•• = Memory 2
••• = Memory 3
V
V