LinkAYL LK-UP211 User manual

www.linkayl.com Copyright © Linkayl Technology Limited
LK-UP211 UPS Control Panel (1.5A)
¢Manual control
¢Remote control
05 06
—Aer power on all the LEDs light for 1 second and turn off, the power indicator LED
normally on
—Press reset buon, all the LEDs light for 1 second and turn off, reset successfully
—L2 will be explosion-flashing aer controller receives fire signal
—External manual switch is equivalent to controller panel switch
—The maximum running me of the motor is 5 minutes
—Press UP buon, the windows open, LED turns on, turns off aer 5 seconds
—Press DOWN buon, the windows close, LED turns on, turns off aer 5 seconds
—Press STOP buon, ,the motors stop, LED turns on, LED turns off aer 1 second
.
—The controller encodes by 433MHz learning code, can store 10 sets of transmission codes
.
£Matching code
—Power the controller on
—Pressing STOP buon on controller for 5 seconds
—LED flashes 3 mes and turns off
—Press UP within 15 seconds
—LED flashes 3 mes and turns off
—Code matched successfully
£Clearing single code
—Power the controller on
—Keep pressing STOP key on the controller for 5S
—LED flashes 3 mes and turns off
—Press DOWN buon on the remote within 15 seconds
—LED flashes 3 mes and turns off, code cleared successfully
£Clearing all codes
—Power controller on
—Pressing STOP /DOWN buon on the controller for 5 seconds
—LEDs flash 3 mes and turn off
—All the codes will be deleted aer this operaon
.
¢Signal control
.
—Manual signal. Control the window by the buons on itself, external dry contact manual
switch and RF remote
—Cascaded signal. As a master controller sends signal to the slave controller, can also be
used as slave controller to receive the signal from the master controller to drive the
window
—Fire signal. Capable of receiving a signal from fire center, smoke sensor, gas detector open
the window automacally, send feedback signal to fire centre
—Rain signal. Aer receiving the signal of rain sensor close the window
—Temperature/humidity signal. Control the window by processing external
temperature/humidity sensor
£Signal and priority
Priority
Signal
Device
1
Manual signal
Panel buons, manual switch, remote, master controller
2
Fire signal
Smoke sensor, gas detector
3
W/R signal
Wired wind rain sensor
4
T/H signal
Temperature sensor, humidity sensor
£Reset and shielding
—Aer manual signal processed controller receives input signal in real me
—Aer processing the signal from fire centre, smoke sensor or gas detector, the controller
immediately shields all the input signals, the controller must be reset by pressing K1
manually
—Aer wired rain sensor signal processed, the controller shields lower priority signal, only
receives the higher priority signal unl reset or manual signal processed
—Aer T&H sensor signal processed, the controller is in the reset state
—If the controller is not connected to a temperature and humidity sensor, the T/H port
must be shielded (put opon switch to “Y” posion)
.
.

www.linkayl.com Copyright © Linkayl Technology Limited
LK-UP211 UPS Control Panel (1.5A)
07 08
—Can be used as a master controller, a slave controller or play a dual role of master & slave
controller at the same me
—As a master controller, connects to the motors or slave controllers to drive them
—As a slave controller, receive the instrucons to drive motors, or drive the motors
independently
—Play a dual role of master & slave controller, not only controlled by higher-level controller,
but also drive motors or lower-level controllers independently
—No maer master, slave or both, it can process all the external signals such as manual
switch, remote and sensors
—Cascade use of the controller, if the master controller connected to an external sensor
(such as smoke sensor, wind and rain sensor, etc.), the slave controller MUST NOT use
inching mode
¢Cascaded control
¢Stroke memory
—The controller can set and memorize opening stroke. Upon the stroke set, the window
opening signal is triggered once, the motor will run the memorized stroke one me
—The default memorized stroke runs for 5 minutes
—Press both of UP/DOWN buons on the controller for 3 seconds, LEDs flash 3 mes and
off, successfully entered the stroke memory seng state
—In the stroke memory seng state, the manual keys are forced to the connued-run
mode, the remote control keys are forced to the inching mode
—Determine the stroke that needs to be memorized by pressing the manual key or the
remote control key by moving or jogging
—Press both of UP/DOWN on the controller for 3 seconds, LEDs flash 5 mes and off, the
memorized stroke set successfully and exit the stroke memory seng state, manual
buons and remote control buons restored to the original mode
—No operaon is performed within 15 seconds, LEDs flash 3 mes and off, the stroke
memory seng state is automacally exited, and the last memorized stroke is retained
—Stroke memory can be set repeatedly. The controller only retains the last successful
stroke value and automacally clears the previous one
—In stroke memory seng state, press both of STOP /DOWN buons on the controller for
3 seconds LEDs flash 3 mes the memorized stroke is deleted and restored to the default
output for 5 minutes
—When the memorized strokes of master controller and slave controller are not the same,
the master controller will run its own memorized stroke. The slave controller will run the
shorter stroke when it receives the cascade signal from the master controller
—The memorized stroke is retained in case the controller is powered down or reset
—When closing the window, the output me is 5 minutes
¢Troubleshoong
—Please read the following instrucons carefully before installing this product
—The control system must be installed by the professional
—The main power must be cut off before wiring to ensure safe operaon
—Two 12V 1.3Ah baeries connected in series
—Please confirm posive and negave polaries before turning on the baeries to ensure
that it cannot be reversed
—The controller does not contain baeries, please purchase with correct size and
specificaons
—Control panel cannot be installed outdoors
—Maximum output power MUST NOT exceed the total rated power of the controller
—Do not use metal objects to touch or cover the controller, otherwise it will affect the
remote control signal recepon
—The maximum transmission distance of the wireless signal can reach 50 meters or more
in the open condion
—The distance between the controller and ground should be more than 1.5 meters
—The distance between the controller and ceiling should be more than 0.3 meters
—The distance between the controller and motor should be more than 1.5 meters
—Avoid stac interference and prevent stac damage to electronic components
—Please use the so wire and cable, aer installaon ensure that the cable carrier is not
affected by the longitudinal tension
—An external sensor must use a product that is compable with this controller
—Non-professionals is not allowed to disassemble the controller. If any funcon is unusual,
please contact your local dealer
.
¢Installaon instrucon
No.
Symptom
Soluon
1
LED flashes, receiver shut down
1. Check the connecon of wires
2. Check the receiver seng
2
LED on the transmier is off or weak
1. Make sure the right installaon of the baery
2. Change the baery
3
The transmier and the receiver work well,
the motor does not work
1. Check the wiring of motor
2. Make sure the motor no failure
.