Linksys WAP200E Operation manual

BUSINESS SERIES
PRODUCT DATA
Model: WAP200E
Wireless-G Exterior Access Point
with Power over Ethernet
High-speed wireless access for
exterior environments!
The Linksys Wireless-G Exterior Access Point lets you connect Wireless-G (802.11g) or
Wireless-B (802.11b) devices to your wired network so you can add PCs to the network
with no cabling hassle. This weather-resistant Access Point creates a “wireless bubble” in
exterior spaces, like patios and outdoor cafés. Power over Ethernet support makes it easy
to install, and you can create multiple BSSIDs that connect to individual VLANs to keep
your traffic separated.
It’s also perfect for use as a bridge, a kind of “cable-less cable” to connect remote areas
together. Maybe your warehouse is in a separate building from your offices. Or maybe you
need to connect the separate buildings of a college campus. With one Wireless-G Exterior
Access Point on each building, you’re connected at up to Wireless-G speeds—with no cable
to run. The weather-resistant housing protects the access point and is lightning protected.
To protect your data and privacy, the Wireless-G Exterior Access Point supports both Wired
Equivalent Privacy (WEP) and the industrial-strength wireless security of Wi-Fi Protected
Access™ (WPA), encoding all your wireless transmissions with powerful encryption. The
MAC Address filter lets you decide exactly who has access to your wireless network, and
advanced logging keeps you apprised. Configuration is a snap with the web browser-based
configuration utility.
RangeBooster technology is a compatible add-on to standard Wireless-G which increases your
wireless network’s range up to two times, and its throughput by up to 35%. Unlike ordinary
wireless technologies that are confused by signal reflections, RangeBooster uses two smart
receivers at each end to detect and decode reflected signals at distances where standard
technologies give up. You’ll find that“dead spots”in the wireless coverage area are reduced, too.
Moreover, the integrated QoS features provide consistent voice and video quality on both
the wired and wireless networks, enabling the deployment of business quality VoIP and video
applications.
Additional features like Multiple BSSIDs, Wireless Roaming, and Auto-Channel selection, make this
solution ideal for your Business.
Add high-speed Wireless-G
MIMO access to the exterior
areas of your small business
network
RangeBooster technology
for up to twice the range,
reduced dead spots, and up
to 35% more throughput
than standard Wireless-G
Weather-resistant housing,
internal high-gain antennas,
and Power over Ethernet
enable safe, simple, exterior
installations
Advanced security with
WPA encryption, logging,
and MAC address filtering
WAP200E
WAP200E

PRODUCT DATA
BUSINESS SERIES
Features
Lightning protected,•
weather-resistant housing
10Base-T/100Base-TX•
Ethernet port, autosensing
half/full duplex and
MDI/MDI-X
Built-in 6-dBi directional•
antenna with 1x2 MIMO to
increase coverage
Obtains power via 802.3af•
Power over Ethernet (PoE)
from a PoE switch or power
injector
Simplified Web interface•
for installation and
configuration
Security Features: 802.1X/•
RADIUS Authentication
Supports WEP,WPA-PSK,•
WPA2-PSK,WPA-ENT,
WPA2-ENT wireless security
Supports 4 BSSID and•
802.1Q VLAN to SSID
mapping
Supports SNMP and intuitive•
Web-based interface
WMM wireless QoS support•
Supports wireless roaming•
based on 802.11F (IAPP)
Supports AP, Bridge Mode•
and Repeater mode
Supports wireless security•
monitoring (working
together with 200 series
client cards)
Supports wireless client•
isolation
3 Year limited warranty•
Wireless-G Exterior Access Point
with Power over Ethernet
Specifications
Model WAP200E
Standards IEEE802.11g, IEEE802.11b, IEEE802.3, IEEE802.3u,
IEEE802.3af (Power over Ethernet), 802.1p (QoS priority), 802.1Q (VLAN),
802.1X (Security Authentication), 802.11i - Ready (Security WPA2),
802.11e - Ready (WMM & U-APSD), 802.11F (Wireless Roaming)
Ports 1 Ethernet, 1 External Antenna
Buttons Reset
Cabling Type UTP CAT 5
LEDs Power, Ethernet, Wireless
Operating System Linux
Setup/Config
Web UI Built-In Web UI for Easy Browser-Based Configuration (HTTP/HTTPS)
Static IP Yes
DHCP Client Yes
Management
SNMP Version 1, 2 and 2c
Event Logging Yes
Web F/W Upgrade Yes
Diags: Flash, etc. Flash, RAM, LAN, WLAN
Operating Modes
Access Point Access Point Mode, Point-to-Point Bridge Mode,
Point-to-Multipoint Bridge Mode, Repeater Mode
Wireless
Spec/Modulation 802.11b/DSSS, 802.11g/ODFM
Data Rates 802.11b: 1, 2, 5.5, 11 Mbps; 802.11g: 6, 9, 11, 12, 18, 24, 36, 48, 54 Mbps
Channels 11 North America, 13 Europe (ETSI and Japan)
Auto-Channel Selection
Number of Internal Antennas 2 x 6 dBi (directional)
Antenna Connector Type Reverse Polarity Female N-Type
Detachable Antenna Yes (sold separately)
RF Power (EIRP) in dBm 802.11g: Typical – 16.5 dBm, 802.11b: Typical – 17 dBm
Antenna Gain in dBi Internal Antenna: 6 dBi
Adjustable Power Yes
Receiver Sensitivity 802.11g: 54 Mbps@ -65 dBm, 802.11b: 11 Mbps@ -85 dBM
Security
WEP/WPA/WPA2 WEP, WPA-PSK, WPA2-PSK, WPA-ENT, WPA2-ENT
Connection Control Wireless Connection Control: MAC-Based
SSID Broadcast SSID Broadcast Enable/Disable
802.1X IEEE 802.1X Support
Wireless Client Isolation Wireless Client Devices Can Be Isolated from Each Other Either
Within an SSID or Between Two SSIDs. However, Both Isolation Modes Can
Be Enabled at the Same Time.
Web-Based Utility
Access Control HTTP/HTTPS, Wireless Client Web GUI Access Control
Wireless Security
WEP Bits 64, 128
WPA Bits and Params. 128 - TKIP/AES
WPA2 Bits and Params. 256 - AES
SSID Broadcast On/Off Yes

PRODUCT DATA
BUSINESS SERIES
Linksys
A Division of Cisco Systems, Inc.
121 Theory
Irvine, CA 92617 USA
E-mail: [email protected]
Web: www.linksys.com
Linksys products are available in more
than 50 countries, supported by
12 Linksys Regional Offices throughout
the world. For a complete list of local
Linksys Sales and Technical Support
contacts, visit our worldwide website
at www.linksys.com
The maximum performance for wireless is derived from IEEE Standard 802.11 specifications. Actual performance can vary, including lower wireless network
capacity, data throughput rate, range and coverage. Performance depends on many factors, conditions and variables, including distance from the access point,
volume of network traffic, building materials and construction, operating system used, mix of wireless products used, interference and other adverse conditions.
Check the product package and contents for specific features supported. Specifications are subject to change without notice.
Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries.
Copyright © 2007 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their
respective holders.
7101510B-SM Model: WAP200E
Client Isolation Yes
MAC-based Wireless
Connection Control Yes
Wireless Web GUI Access On/Off Yes
Quality of Service
QoS 4 Queues
WMM Wireless Traffic Prioritization
General
Wireless Roaming Based on IAPP (802.11F)
Auto-Channel Selection
Environmental
Dimensions 6.42" x 8.07" x 2.17"
W x H x D (163 x 205 x 55 mm)
Unit Weight 2.47 lb (1.121 kg)
Mounting options Industrial-Strength, weather-resistant housing, lightning protection for
outdoor enclosure, ceiling- or wall-mountable
Power 48VDC
Max Power Draw: 4.8 W
PoE In Y/N Yes
Certification FCC, IC,CE
Operating Temp. -4 to 140ºF (-20 to 60ºC)
Storage Temp. -4 to 140ºF (-20 to 60ºC)
Operating Humidity 5 to 95%, Noncondensing
Storage Humidity 5 to 95%, Noncondensing
Package Contents
Wireless-G Exterior Access Point with Power over Ethernet•
User Guide on CD-ROM•
Mounting Plate with Hardware•
12-ft Weather-Resistant Network Cable•
Registration Card•
Minimum Requirements
802.11b or 802.11g Wireless Adapter with TCP/IP Protocol Installed per PC•
Switch/Router with Power over Ethernet (PoE) Support or PoE Injector•
Web-Based Configuration: Java-Enabled Web Browser•