Lippert Components Schwintek TV Lift User manual

SCHWINTEK TV LIFT
OEM INSTALLATION MANUAL

Rev: 01.22.20 Page 2 CCD-0001576
Introduction
The Schwintek TV Lift is designed with a maximum operating weight rating of 100 lbs. Do NOT exceed the
maximum operating weight rating.
Safety Information
Read all instructions and safety labels before starting product installation.
TABLE OF CONTENTS
Introduction 2
Safety Information 2
Resources Required 2
Installation 3
Initial Programming 4
Setting the Electronic Stop Limits 5
Operation 5
TV and Rack Removal From Lift, if Desired 5
Sync Remote, if Included 5
Wiring Diagram 6
Notes 7
Failure to follow the instructions provided in this manual may result in death, serious personal injury,
severe unit damage or voiding of the component warranty.
The unit MUST be supported per manufacturer's recommendations before working underneath.
Failure to do so may result in death or serious personal injury.
Always wear eye protection when performing service or maintenance to the unit. Other safety
equipment to consider would be hearing protection, gloves and possibly a full face shield, depending
on the nature of the service.
Moving parts can pinch, crush or cut. Keep clear and use caution.
Do NOT exceed the 100-lb operating weight rating or damage to the product may occur.
Resources Required
• Cordless or electric drill or screw gun
• Appropriate drill bits
• Appropriate drive bits
• #10 Phillips pan head screws
• Phillips screwdriver
• ¼" Spade-type electrical connectors

Rev: 01.22.20 Page 3 CCD-0001576
Motor with
Bearing Block
Control
Motor
Control
Wires
Fig. 1
Fig. 2
Installation
1. Make sure the unit is level.
2. Mount bearing block with motor (Fig. 1) to solid backer, centered within cabinet, using #10 screws.
3. Mount TV lift controller close to end of motor using #10 screws.
A. Plug motor control wires into controller (Fig. 2).
B. Attach the power, ground and switch wires with ¼” spade type connectors (Fig. 7).
NOTE: The wire harness-to-battery and switch are customer-supplied items. Harness wires must be 10
AWG minimum. Also, 30 amp circuit protection should be installed on the power lead wire between
the battery and the controller. See figure 7.
4. Mount included TV plate to the back of the TV and the rack.
A. Insert rack into bearing block by aligning the V-grooves in the rack to the V-rollers in the bearing
block.
#10 Screws
4 Places

Rev: 01.22.20 Page 4 CCD-0001576
Fig. 3
Fig. 4
B. Insert rack until the gear in the bearing block comes into contact with the serpentine groove of
the rack (Fig. 3).
C. Press the switch's RETRACT button (Fig. 4) until the rack is fully inserted into the bearing block.
5. Mount the cabinet top angle transition plate onto the rack (Fig. 5).
Fig. 5
A B C
Fig. 6
Initial Programming
NOTE: The control's green LED (Fig. 6B) will flash and its red LED (Fig. 6C) will light up solid.
If the lights do not do as stated in NOTE above then enter programming mode. Press and hold the white
CONFIGURATION button (Fig. 6A), located on the control, for five seconds.

Rev: 01.22.20 Page 5 CCD-0001576
Setting the Electronic Stop Limits
1. To set the lower electronic stop, press and hold the switch's RETRACT button (Fig. 4) to lower the TV
into the desired position, then press the control's white CONFIGURATION button once (Fig. 6A).
2. To set the raised electronic stop, press and hold the switch's EXTEND button to raise the TV into the
desired position, then press the control's white CONFIGURATION button once.
3. Test the receiver’s programming by lowering and raising (retracting and extending) the TV.
Operation
1. To raise the TV, press and release the switch's EXTEND button (Fig. 4). The TV will raise into position
and stop at the preset stop limit.
2. To lower the TV, press and hold the switch's RETRACT button until the TV is fully lowered into the
cabinet.
NOTE: For safety purposes, the switch will need to be held until lowered to the preset stop limit.
TV and Rack Removal from Lift, if Desired
To remove the TV and rack out of the lift unit, do as follows:
1. Press and hold the control's white CONFIGURATION button (Fig. 6A) for five seconds.
NOTE: The control's red LED (Fig. 6C) will light up solid and the green LED (Fig. 6B) will flash.
2. Press and hold the switch's EXTEND button until the rack and TV are fully raised so they can be
removed from the system.
Sync Remote, if Included
1. Locate white CONFIGURATION button (Fig. 6A).
2. Press the button two times and hold on the third time.
3. The green LED (Fig. 6B) and the red LED (Fig. 6C) will alternately flash.
4. Hit any button on the remote (Fig. 7).
5. The green LED (Fig. 6B) and the red LED (Fig. 6C) will flash at the same time, then stop.
6. The remote is now synced.
Fig. 7

Rev: 01.22.20 Page 6 CCD-0001576
+−
236575 Motor
253396 Control
199082 Switch
12V DC Battery
30 Amp
Circuit
Protection
Front of Switch
Back of Switch
Switch Control Circuit Protection 12V DC Battery
Top Pin (EXTEND) UP SW
Middle Pin (Power) BATT (+) 30 Amp Positive (Red) Post
Bottom Pin (RETRACT) DOWN SW
BATT (-) Negative (Black) Post
Fig. 8
Wiring Diagram

Rev: 01.22.20 Page 7 CCD-0001576
Notes

The contents of this manual are proprietary and copyright protected by Lippert Components, Inc. (“LCI”).
LCI prohibits the copying or dissemination of portions of this manual unless prior written consent from an
authorized LCI representative has been provided. Any unauthorized use shall void any applicable warranty.
The information contained in this manual is subject to change without notice and at the sole discretion of LCI.
Revised editions are available for free download from lci1.com.
Please recycle all obsolete materials.
For all concerns or questions, please contact
Lippert Components, Inc.
Ph: [phone] | Web: lci1.com | Email: [email protected]