Lite-Puter EDX-607A User manual

EDX-607A [EUM-G] 1
User Manual
EDX-607A
6 Channel Integrated Dimmer Pack

EDX-607A [EUM-G] 2
Index
0 BEFORE INSTALLATION ...................................................................................................................4
1 INTRODUCTIONS ...............................................................................................................................5
1-1 FEATURES.......................................................................................................................................5
1-2 SPECIFICATIONS ..............................................................................................................................6
1-3WIRING DIAGRAM ............................................................................................................................7
1-4 INSTALLATION ..................................................................................................................................8
1-5 PANEL INTRODUCTION....................................................................................................................11
2 OPERATIONS....................................................................................................................................12
2-0 EDX SYSTEM................................................................................................................................12
2-1 FUNCTIONS ...................................................................................................................................14
2-2 INITIALIZATION................................................................................................................................15
2-3 DMX START CHANNELADDRESS SETTING ......................................................................................15
2-4 ZONE SETTING ..............................................................................................................................16
2-5 PARTITION SETTING .......................................................................................................................17
2-6 ID NUMBER SETTING .....................................................................................................................22
2-7 FADE TIME SETTING.......................................................................................................................22
2-8 SYSTEM CLOCK SETTING ...............................................................................................................23
2-9 TIMER ON/OFF.............................................................................................................................23
2-10 DIMMING /SWITCH /FLUORESCENT MODE SETTING........................................................................24
2-11 DISPLAY SYSTEM TEMPERATURE ..................................................................................................25
2-12 DISPLAY CURRENT LOAD..............................................................................................................25
2-13 SET TIMER ..................................................................................................................................26
2-14 SCENE SETTING ..........................................................................................................................27
2-15 SCENE RECALL............................................................................................................................28
2-16 MEMORY &BUTTON LOCK/UNLOCK FUNCTION..............................................................................28
2-17ADJUST AND VIEW DIMMING VALUE...............................................................................................28
2-18 PANEL LED ON/OFF SETTING........................................................................................................29
2-19 DIMMING CURVE SETTING............................................................................................................30
2-20 ENABLE/DISABLE PARTITION FUNCTION ........................................................................................30
2-21 CHECK SOFTWARE VERSION........................................................................................................31
2-22 ENABLE/DISABLE IR REMOTE CONTROL .......................................................................................31
2-23 ENABLE/DISABLE SC5/6 OVERLAP SCENE FUNCTION....................................................................32

EDX-607A [EUM-G] 3
2-24 CLOCK SYNCHRONIZATION ...........................................................................................................32
LIMITED WARRANTY..........................................................................................................................33

EDX-607A [EUM-G] 4
0 Before Installation
1. The setting of dimmer or non-dimmer mode:
The dimming/non-dimming (switch) mode should be preset before the lamps/loads being connected to
the devices. Please refer to “Dimmer/Switch Mode Setting” in this manual.
2. Current Loading Precaution:.
Please keep adequate ventilation. If the machine’s internal temperature is over 65°C, the device will
stop output.
The maximum output of each channel is 4A. The maximum output of the 6 channels in total is 8A .
3. Instruction of power/ load wiring:
Connector size range AWG 22-14
Use Copper Conductors Only, 60/75C, Tighten To 12 pound-inches.
4. Suggested Environment:
Ambience Temperature: under 35°C
Humidity: 40% ~ 80%
5. About wiring:
Please check EDX/DMX-512 wiring guide on Lite-Puter’s website:
http://www.liteputer.com.tw/tech_guide.asp

EDX-607A [EUM-G] 5
1 Introductions
1-1 Features
1. 6 channels. The maximum output of each channel is 4A; the maximum output in total is 8A .
2. The master panel can store 12 scenes, display 12 channels dimming value, and transmit 12
channels DMX-512 signal.
3. IR remote controller (optional) can recall 6 scenes, adjust any channel’s dimming level, and
edit 6 scenes directly. User can also view current zone number and set fade in/fade out time by
IR remote controller
4. C1, C2, C3 liner dimming curve.
5. Fade in/fade out time setting.
6. Timer control can execute preset lighting scenes automatically (24hours).
7. Each channel can be set as dimming, switch or fluorescent mode.
8. Display system temperature and detect temperature automatically. When the internal
temperature is over 70°C, it will alert and limit the output to 50%. Over 75°C it will stop output
automatically.
9. Display total current. If total current is over 25A, it will switch off automatically and press【OFF】
to restart the device . If total current is over 20A, it will limit the output to 12A and press any
button to restart the system.
10. Can be connected to scene control panels (ECP series).
11. Lock/unlock.

EDX-607A [EUM-G] 6
1-2 Specifications
Power: AC 100 –240V, 50/60Hz
Output: 4A per channel, total 8A . Leading edge (forward phase) dimming control.
Protocol: DMX-512/ EDX (RS-485)
Dimension: 212 (W) x 118 (H) x 60 (D)mm
Weight: 0.88 KG
Fuse：PCB No.: QB18B F1 (Resistive fuse 20A, 250V)
F2 (Resistive fuse 1A, 250V)
F3 (Resettable fuse)

EDX-607A [EUM-G] 7
1-3 Wiring Diagram

EDX-607A [EUM-G] 8
1-4 Installation
1. Please refer chapter 2-10 to set switch mode before connecting no-dimmable lamps. Non-dimmable
lamps might be damaged by dimming mode.
2. Please make sure the ambience temperature is under 40°C.
3. Please ensure that wall-mounted area has at least 75mm in depth.

EDX-607A [EUM-G] 9

EDX-607A [EUM-G] 10

EDX-607A [EUM-G] 11
1-5 Panel Introduction
1
Scene buttons
2
IR receiver
3
LED
4
Channel dimming value display or other function
5
Function buttons
6
CH1- CH12 dimming value UP
7
CH1- CH12 dimming value DOWN

EDX-607A [EUM-G] 12
2 Operations
2-0 EDX System
EDX is a protocol specifically designed for architectural and environmental lighting applications. EDX
dimmers or devices are able to store scenes in themselves.
Each EDX device or ECP panel can be specified by a zone number. The scenes stored in EDX devices
can be recalled by ECP panels with the same zone number.
For example, EDX devices configured as zone 1 can be controlled (recall scenes) by ECP panel
configure as zone 1. EDX devices configured as zone 5 can be controlled (recall scenes) by ECP
panel configure as zone 5.
Figure 1: One EDX device with one ECP scene panel

EDX-607A [EUM-G] 13
Figure 2: Multiple EDX devices with ECP scene panels
ECP scene panel 1 controls EDX device 1.
ECP scene panel 2 controls EDX device 2.
* If there are both DMX-512 and EDX signal present, DMX-512 signal has the highest priority.

EDX-607A [EUM-G] 14
2-1 Functions
Hold 【FCN】for 3 seconds and then press【FCN】to select a function from the following list:
Display
Combined Button
Function
【FCN】+【CH1_UP】
Set ID No.
【FCN】+【CH2_UP】
Set Zone No.
【FCN】+【CH3_UP】
Set DMX start channel address
【FCN】+【CH4_UP】
Set scene fader time
【FCN】+【CH5_UP】
Modify system clock
【FCN】+【CH6_UP】
Timer on/off
【FCN】+【CH1_DOWN】
Channel dimming mode setting
【FCN】+【CH1_DOWN】
Channel non-dimming/switch mode
setting
【FCN】+【CH1_UP】
Channel fluorescent mode setting
【FCN】+【CH2_DOWN】
View and set the timer
【FCN】+【CH3_DOWN】
Display system temperature
【FCN】+【CH4_DOWN】
Display the load current
【FCN】+【CH5_DOWN】
Display the panel LED on /off
【FCN】+【CH6_DOWN】
Select dimming curve
Partition setting
Partition function on/off

EDX-607A [EUM-G] 15
IR remote control on/off
SC5/SC6 overlap scene function
switch
Software version
Clock Synchronization on/off
P.S: There are 2 ways to enter function menu.
A. Hold【FCN】for 3 seconds, then press【FCN】to select functions.
B. Use combined buttons to select a function then press【FCN】to enter the setting.
After setting, press【ENTER】to store. Press any scene buttons to exit function setting without change.
The system will exit the setting mode after 60 seconds idling.
2-2 Initialization
Hold【ENTER】+【SHIFT】+【OFF】at the same time for 3 seconds to initialize the system.
2-3 DMX Start Channel Address Setting
One DMX-512 universe has 512 channels. EDX-607 must select 12 continuous channels from these
512 channels. The first channel’s address of the 12 continuous channels is named as EDX-607’s DMX
start channel address.
STEP-1: Press【FCN】+【CH3_UP】at the same time or hold【FCN】for 3 seconds to enter function
menu and then press【FCN】twice to select function , the screen will display its DMX start channel
address .
STEP-2: Press【▲】or【▼】, DMX ADR (DMX address) will increase or decrease 10 addresses at one
time. Press【】or【】, DMX ADR will increase or decrease 1 address at one time.
STEP-3: After setting, press【ENTER】to save and exit.

EDX-607A [EUM-G] 16
2-4 Zone Setting
About zone: User must set zone code of EDX-607 before using. This code has two parts. The first part
is zone number and the second is start channel address.
STEP-1: Press【FCN】+【CH2_UP】at the same time or hold【FCN】for 3 seconds to enter function
menu and then press【FCN】once to select function ,the screen will display the zone code .
STEP-2: Press【▲】or【▼】to adjust the value; press【】or 【】to select the editing items.
STEP-3: Press【ENTER】to save and exit.
Example:
If zone number is 1 and the start channel is 1.To set zone as 3 and set start channel as 2. The steps
are as follows.
1. Press【FCN】+【CH2_UP】at the same time or hold【FCN】for 3 seconds to enter function menu
and then press【FCN】once to select function. The screen will display, (The two digits on the right side
are blinking.)
2. Press【 】once, the two digits on the left side are blinking, it will display,
3.Press【▲】twice, it will display,
4. Press【】once, The two digits on the right side are blinking, it will display,
5. Press【▲】once, it will display,
6. Press【ENTER】to save and exit.

EDX-607A [EUM-G] 17
2-5 Partition Setting
Generally, all channels on EDX-607 can be set to only 1 zone.
To make EDX-607 more flexible, you can assign each channel on EDX-607 to different zones by using
partition function.
For example, you assign channel 1 –3 on EDX-607 to partition 1 and channel 4 –6 on EDX-607 to
partition 2. There are 2 control panels (ECP-106) connected to EDX-607, one is set to zone 1; the
other is set to zone 2. If scenes are recalled by ECP-106 of zone 1, only channel 1 –3 on EDX-607 will
change their dimming levels. If scenes are recalled by ECP-106 of zone 2, only channel 4 –6 on
EDX-607 will change their dimming levels. However, if scenes are recalled by EDX-607’s panel directly,
the dimming levels of channel 1 –6 will be all changed.
STEP-1: Hold【FCN】for 3 seconds to enter function menu and then press【FCN】12 times until the
screen shows .
STEP-2: Press【▲】to enable partition function, the screen shows
STEP-3: Hold【FCN】for 3 seconds to enter function menu and then press【FCN】12 times until the
screen shows .
STEP-4: Press【】or【】to select partition no. and press【CH1- CH12 UP】to select channels to
partition; press【CH1- CH12 DOWN】to cancel channels out of partition.
STEP-5: Press【ENTER】to save and exit.

EDX-607A [EUM-G] 18
Example:
To set channel 1 to partition 2, channel 10 to partition 1 and 3, and other channels to partition 1
(default). The steps are as follows.
Enter . The LED bars of channel 1 ~ 6 show all of them are in partition 1.
Press【SHIFT】to check channel 7 ~ 12,
the LED bar of each channel shows that channel 7 –12 belong to partition 1.

EDX-607A [EUM-G] 19
Press【SHIFT】shift back to channel 1 ~ 6. Press【CH1_DOWN】to remove channel 1 from partition.
LED bar of channel 1 is blank.
Press【】to shift to partition 2.
By default, no channel belongs to partition 2

EDX-607A [EUM-G] 20
Press【CH1_UP】to set channel 1 to partition 2, the LED bar shows that channel 1 is in partition 2 now.
Press【】once to shift to partition 3.
By default, no channel belongs to partition 3
Press【SHIFT】shift to channel 7 ~ 12.