Litex Industries CC42BB4L User manual

Installation Guide
For Models:
CC42BB4L
CC42WW4L
net weight of fan: 9.47 lb. (4.3 kg) PRINTED IN CHINA
Table of Contents:
Safety Tips. pg. 1
Unpacking Your Fan. pg. 2
Parts Inventory. pg. 2
Installation Preparation. pg. 3
Hanging Bracket Installation. pg. 3
Preparation for Wiring. pg. 4
Wiring. pg. 4
Fan Assembly. pg. 5
Motor Housing Assembly. pg. 5
Blade Assembly. pg. 6
Light Assembly. pgs. 6 - 7
Testing Your Fan. pg. 7
Troubleshooting. pg. 8
Parts Replacement. pg. 8
Warranty. pg. 8
READ THESE INSTRUCTIONS AND
SAVE THEM FOR FUTURE USE
4009654

SAFETY TIPS.
page 1
WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit
panel before you begin the fan installation or before servicing the fan or installing accessories.
1. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND
SAVE THESE INSTRUCTIONS.
CAUTION: To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp edges.
2. Make sure all electrical connections comply with Local Codes or Ordinances, the National Electrical Code, and
ANSI/NFPA 70-1999. If you are unfamiliar with electrical wiring or if the house/building wires are different
colors than those referred to in the instructions, please use a qualified electrician.
3. Make sure you have a location selected for your fan that allows clear space for the blades to rotate, and at
least seven (7) feet (2.13 meters) of clearance between the floor and the fan blade tips. The fan should be
mounted so that the tips of the blades are at least thirty (30) inches (76 centimeters) from walls or other
upright structures.
4. The outlet box and ceiling support joist used must be securely mounted, and capable of supporting at least
35 pounds (16 kilograms). The box must be supported directly by the building structure. Use only ETL or
UL listed outlet boxes marked "FOR FAN SUPPORT."
WARNING: To reduce the risk of fire, electrical shock, or personal injury, mount to the outlet box marked
"Acceptable for Fan Support of 15.9 kg (35 lb) or less" and use the mounting screws provided with the outlet box.
Most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan support and may
need to be replaced. Consult a qualified electrician if in doubt.
WARNING: To reduce the risk of fire, electrical shock, or personal injury, wire connectors provided with this fan are
designed to accept only one 12 gauge house wire and two lead wires from the fan. If your house wire is larger than
12 gauge or there is more than one house wire to connect to the corresponding fan lead wires, consult an
electrician for the proper size wire connectors to use.
5. Electrical diagrams are for reference only.
6. After installation is complete, check that all connections are absolutely secure.
7. After making electrical connections, spliced conductors should be turned upward and pushed carefully up
into the outlet box. The wires should be spread apart with the grounded conductor and the
equipment-grounding conductor on opposite sides of the outlet box.
WARNING: To reduce the risk of electrical shock, fire and to prevent humming noise do not use this fan with any
solid state speed control device or control fan speed with a full range dimmer switch. [Using a full range dimmer
switch to control fan speed will cause a loud humming noise from fan.]
8. Do not operate the reverse switch until the fan has come to a complete stop.
9. Do not insert anything between the fan blades while they are rotating.
WARNING: To reduce the risk of personal injury, do not bend the blade arms during assembly or after installation.
Do not insert objects into the path of the blades.
WARNING: To avoid personal injury or damage to the fan and other items, be cautious when working around or
cleaning the fan.
10. Do not use water or detergents when cleaning the fan or fan blades.A dry dust cloth or lightly dampened
cloth will be suitable for most cleaning.
WARNING: To reduce the risk of personal injury, use only parts provided with this fan. The use of parts OTHER
than those provided with this fan will void the warranty.
NOTE: The important safety precautions and instructions appearing in the manual are not meant to cover all
possible conditions and situations that may occur. It must be understood that common sense and caution are
necessary factors in the installation and operation of this fan.

page 2
1. Unpacking Your Fan.
Carefully open the packaging. Remove items from
Styrofoam inserts. Remove motor housing and place
on carpet or Styrofoam to avoid damage to finish. Do
not discard fan carton or Styrofoam inserts should
this fan need to be returned for repairs.
Check against parts inventory that all parts have
been included.
2. Parts Inventory.
a. hanging bracket. 1 piece
b. motor housing. 1 piece
c. motor assembly. 1 piece
d. glass shade. 1 piece
e. blade arm. 4 pieces
f. blade. 4 pieces
g. hardware packs
e
g
required bulb:
1 x 6.5 watt LED medium base bulb
(included)
IMPORTANT REMINDER: You must
use the parts provided with this fan for
proper installation and safety.
c
a
b
d
f

4. Hanging Bracket Installation.
page 3
hanging
bracket
spring washers
ON
OFF
ON
OFF
3. Installation Preparation.
To prevent personal injury and damage, ensure
that the hanging location allows the blades a
clearance of 7ft. (2.13m) from the floor and 30in.
(76cm) from any wall or obstruction.
This fan is suitable for room sizes up to 144
square feet (13.4 square meters).
This fan can be mounted as a flushmount
on a regular (no-slope) ceiling only. Downrod
installations are not available for this fan.
Installation requires these tools:
Phillips screwdriver, flat-head screwdriver,
adjustable pliers or wrench, stepladder, wire
cutters, and rated electrical tape.
flushmount
installation
outlet box screws
10ft. - 12ft.
10ft. - 12ft.
(3m - 3.6m)
blade edge
7 feet
(2.13m)
(76cm)
30
inches
(3m - 3.6m)
flat washers
downrod
installation
CANNOT be
installed on
angled or
vaulted ceilings
Turn off circuit breakers to current fixture from
breaker panel and be sure operating light switch is
turned to the OFF position.
WARNING: Failure to disconnect power supply prior
to installation may result in serious injury.
Remove existing fixture.
WARNING: When using an existing outlet box, be
sure the outlet box is securely attached to the
building structure and can support the full weight of
the fan. Ensure outlet box is clearly marked "Suitable
for Fan Support." If not, it must be replaced with an
approved outlet box. Failure to do so can result in
serious injury.
CAUTION: Be sure outlet box is grounded properly
and that a ground wire (GREEN or BARE) is present.
Install hanging bracket to outlet box using original
screws, spring washers and flat washers provided
with new or original outlet box. Pull electrical
wiring from outlet box through center hole in the
hanging bracket.
*Note:It is very important that you use the proper
hardware when installing the hanging bracket as
this will support the fan.

page 4
Remove 1 motor mounting screw from hook end
of motor assembly. Remove the other 2 motor
mounting screws from hanging bracket. Save
motor mounting screws for later use.
Lift motor assembly to hanging bracket and slide
hook end (with single screw hole) into square
opening on hanging bracket (see diagram at
right).This will allow the motor assembly to hang
out of the way while wiring.
Tip: Seek the help of another person to hold the
stepladder in place and to lift the fan up to you
once you are set on the ladder.
6.Wiring.
motor assembly
*
WHITE
WHITE
BLACK
BLACK
BLUE
GROUND (GREEN OR BARE)
GREEN
5. Preparation for Wiring.
hanging
bracket
hanging
bracket
motor assembly
motor
mounting
screws
hook end
WARNING:Turn off circuit breakers to current fixture
from breaker panel and be sure switch is turned to
the OFF position.
NOTE:See instructions above (Section 5) in order to
temporarily hang fan on hanging bracket during
wiring.
CAUTION: Be sure outlet box is properly grounded and
that a ground wire (GREEN or Bare) is present.
Make sure all electrical connections comply with Local
Codes or Ordinances and the National Electrical Code.If
you are unfamiliar with electrical wiring or if the
house/building wires are different colors than those
referred to in the instructions below, please use a
qualified electrician.
When fan is secured in place on the hanging bracket,
electrical wiring can be made as follows:
Connect BLACK and BLUE wire from fan to BLACK
wire from ceiling with wire connector provided.
Connect WHITE wire from fan to WHITE wire from
ceiling with wire connector provided.
Connect all GROUND (GREEN) wires from fan
together to BARE/GREEN wire from ceiling with wire
connector provided
If you intend to control the fan light with a separate
light switch, connect BLUE wire from fan to the
BLACK supply from the independent switch.
* Wrap each wire connector separately with electrical
tape as an extra safety measure.

Carefully push wiring and wire connectors
into outlet box. Leave hook end of motor
assembly in square opening of hanging
bracket and lift the other end of motor
assembly toward hanging bracket.
Align motor assembly screw holes with
hanging bracket screw holes and re-insert
motor mounting screws that were
previously removed (Section 5, page 4).
Securely tighten all motor mounting
screws with a Phillips screwdriver.
8. Motor Housing Assembly.
page 5
7. Fan Assembly.
Hold motor housing up to hanging bracket to
determine which 2 screws align with slotted holes
on top rim of motor housing. Lower motor
housing and partially loosen the 2 screws in
hanging bracket that correspond to slotted holes
in motor housing. Remove the other two screws
from hanging bracket.
Raise motor housing to hanging bracket again,
allowing slotted holes in motor housing to align
with loosened screws in hanging bracket.Twist
motor housing to lock. Re-install the 2 screws that
were removed and then tighten all screws to
secure motor housing.
motor
mounting
screws
motor
mounting
screw
motor
housing
screws
motor
housing
screws
motor
housing

page 6
Time Saver: Washers for blade screws can be
set on each blade screw prior to installing
blades.
Locate 12 blade attachment screws and
washers in hardware pack. Hold blade arm up
to blade and align holes. Insert 3 blade
attachment screws (along with washers) with
fingers first and then tighten screws securely
with a Phillips screwdriver. Repeat for the
remaining blades.
Remove blade arm screws and lock washers
from underside of motor. If plastic motor locks
are installed with blade arm screws, discard
plastic motor locks (save blade arm screws and
lock washers to secure blade arms). Align blade
arm holes with motor screw holes and attach
blade arm with lock washers and blade arm
screws. Before securing screws premanently,
repeat procedure with remaining blade arms.
Securely tighten all screws.
Note: Tighten blade arm screws twice a year.
9. Blade Assembly.
blade arm
blade
motor housing
blade attachment
screws and washers
blade arm screws
lock washers
plastic
motor lock
10. Light Assembly.
Install 1 medium base 6.5 watt LED bulb
(included).
Important: When replacing bulb, please allow
bulb and glass shade to cool down before
touching them.
Partially loosen 3 thumbscrews in light kit plate.
["Light Assembly" continued on next page.] bulb
thumbscrew
light kit plate
thumb-
screw

page 7
10. Light Assembly. (cont.)
11.Testing Your Fan.
It is recommended that you test fan before
finalizing installation. Restore power from circuit
box and wall switch. Test fan speeds with the pull
chain to the left of the reverse switch. Start at the
OFF position (no blade movement). First pull will set
the fan to HI. Second pull will set the fan to
MEDIUM. Third pull will set the fan to LOW. Fourth
pull will re-set the fan to OFF setting. Test light kit
with the pull chain to the right of the reverse switch.
(Refer to diagram 1.) If fan and/or light do (does) not
function, please refer to "Troubleshooting" section
to solve any issues before contacting Customer
Service.
Turn fan completely off before moving the reverse
switch. Set reverse switch to recirculate air
depending on the season:
- DOWN position in summer (diagram 2)
- UP position in winter (diagram 3)
A ceiling fan will allow you to raise your thermostat
setting in summer and lower your thermostat
setting in winter without feeling a difference in your
comfort.
Important: Reverse switch must be set either
completely UP or completely DOWN for fan to
function. If the reverse switch is set in the middle
position (diagram 4), fan will not operate.
pull chain
extension
Raise glass shade to light kit plate, pushing up
gently until lip on glass shade fits securely
inside light kit plate. Re-tighten thumbscrews.
Do not overtighten thumbscrews as glass may
crack or break. Make sure that glass shade is
secure by pulling down GENTLY on glass shade.
Note: Do NOT remove the rubber ring on lip of
glass shade as this (along with the
thumbscrews) helps hold the glass shade in
place.
Attach pull chain extensions supplied or
custom pull chain extensions (sold separately)
to the ends of the pull chains.
glass shade
thumbscrew
light kit plate
thumb-
screw
pull chain
extension
reverse
switch
light
pull chain
fan
pull chain
diagram 2
diagram 1
diagram 3 diagram 4

page 8
Warranty.
Parts Replacement.
Troubleshooting.
LITEX 15-YEAR LIMITED WARRANTY:
LITEX INDUSTRIES, LTD. warrants this fan to the original
household purchaser for indoor use under the following
provisions:
1-YEAR WARRANTY: LITEX INDUSTRIES, LTD. will replace or
repair any fan which has faulty performance due to a
defect in material or workmanship.Contact Litex Customer
Service at 1-800-527-1292 to arrange for return of fan.
Return fan, shipping prepaid, to Litex Industries, Ltd.We will
repair or ship you a replacement fan, and we will pay the
return shipping cost.
5-YEAR WARRANTY: LITEX INDUSTRIES, LTD. will repair or
replace, at no charge to the original purchaser, any fan
motor that fails to operate satisfactorily when failure
results from normal use.
RETURN FAN MOTOR ONLY, shipping prepaid, to Litex
Industries.We will repair or ship purchaser a replacement
motor and Litex will pay the return shipping cost.
6 to 15-YEAR LIMITED WARRANTY: LITEX INDUSTRIES, LTD.
will repair the fan, at no charge to the original purchaser
for labor only, if the fan motor fails to operate satisfactorily
when failure results from normal use. Parts used in the
repair will be billed to the purchaser at prevailing prices at
time of repair.
The purchaser shall be responsible for all costs incurred
in the removal, reinstallation and shipping of the product
for repairs.
This warranty does not apply when damage from
mechanical, physical, electrical or water abuse results in
causing the malfunction. Deterioration of finishes or other
parts due to time or exposure to salt air is specifically
exempted under this warranty.
Neither Litex Industries nor the manufacturer will
assume any liability resulting from improper installation or
use of this product. In no case shall the company be liable
for any consequential damages for breach of this, or any
other warranty expressed or implied whatsoever.This
limitation as to consequential damages shall not apply in
states where prohibited.
For parts and information please refer to
"Parts Inventory" on page 2.
Litex Customer Support:
1-800-527-1292
Problem: Fan fails to operate.
Solutions:
1. Check wall switch to fan.
2.Verify that reverse switch is set completely in
either direction.
3. Check to be sure fan is wired properly.
Problem: Light kit not lighting.
Solutions:
1. Check wall switch to fan.
2. Check that bulb is installed correctly.
3. Check to be sure wires in outlet box are wired
properly.
Problem: Fan operates but light fails.
Solutions:
1. Check that bulb is installed correctly.
2. Check to be sure wires in outlet box are wired
properly.
3. Replace defective bulb with same type of bulb.
WARNING: Failure to disconnect power supply
prior to troubleshooting any wiring issues may
result in serious injury.
PWLI1708