Little Folks Furniture Fargo BKC001 User manual

Code: BKC001
Fargo Bookcase

Treated properly it should be a faithful servant for years - and we hope you get the
same amount of pleasure from it. Before you do
lplease take a few minutes to read these instructions
lwe suggest you carefully unpack everything, lay it out on a clean, flat floor and
identify everything on the parts list in these instructions. Do not throw away any
packaging until you are sure you have all the parts.
If you have any problems assembling the product please call our customer services
on 01985 300588 and we will try and help. If for any reason you wish to return the
product, you must disassemble the product and pack in the original packaging.
Taking care of your product
Your furniture should require no more than a regular dust off with a soft cloth. If the furniture is
not painted then a superior wood polish can be used - but never use polishes containing
silicone.
If necessary it can be cleaned with a damp cloth with a mild detergent solution - and then
dried with a lint-free cloth. Never clean with abrasives or chemical cleaners.
Direct sunlight or heat from a radiator can stain, discolour warp or crack furniture.
We know furniture can be heavy but try not to drag furniture across the floor as this can
damage it.
Thank you for buying a
Periodically check all fittings to ensure that none have come loose.
Keep away from direct sources of heat, such as electric, gas or wood fires.
Do not allow children to climb on the furniture. Larger items of furniture should be
properly (and professionally) secured to the wall to prevent them toppling over.
Using this furniture other than for its intended purpose could cause damage the
structure or serious injury to your child.
The furniture should not be used if any structural part is broken or missing.
PRODUCT SAFETY
piece of furniture
If you have any problems please do contact us for help on e
mail [email protected] or phone our
CUSTOMER SERVICES 01985 300588

Parts list
Fittings
Tools Req
Screwdriver
8 x Dowels
Left Side
Top
Plinth
Base
Right Side
Middle
2 x Back PCS
12 x Cam Pins
12 x Cams
Shelf
4 x shelf studs

Assembly
Fit the base
2 x Cam Pins, 4 wooden dowels and a Screwdriver
Fit 2x Cam Pins into the smaller holes as shown and then push the wooden dowels into the
large end holes of the base panel.
Fit the two sides
4 x wooden Dowels and 4 x cam pins
push the 4 wooden dowels into the large holes at the top of each side.
Then screw in 4 x cam pins into the smaller holes as seen
X 4
X 4
X 2
X 4
Underside of base

Assemble the bookcase
3 x cam pins and 7 x cams
fix the plinth to the underside of the base, insert 2 x cams into the plinth holes and
tighten.
Align the sides to the base & plinth and connect the parts using the fittings that you
have already applied. Now insert 4 cams into the holes and tighten.
Fix one cam pin into the base panel at the rear (see image) then align the middle
piece onto the cam pin (cam hole facing outwards), insert the cam and rotate to
tighten.
X 3
Slip in the back panels
Slide the two back panels down the slots and into the bottom groove in the base.
Please orientate the back panels with the decorative groove facing inwards

Fix the top
5 x cam pins
Now lower the top down onto the carcass. Line up the cam pins, wooden dowels
and back panels so that the all parts are connected.
Rotate the cam pins to tighten the parts together.
X 5
Connect the top
5 x cams
Now lower the top down onto the carcass. Line up the cam pins, wooden dowels
and back panels so that the all parts are connected.
Rotate the cam pins to tighten the parts together.

Drop in the shelves
4 x shelf studs
insert 2 studs into each side panel, selecting the height of the shelf.
now simply rest the shelf on the studs.
Locate the bookcase
Decide where you would like to place the bookcase, now gently lift the bookcase
into place making sure that the bookcase is on a stable surface.