Little Folks Furniture CBD001 User manual

Product Safety
Care of your Product
Welcome
Product Care
Customer Service 01985 300588
Clean your cabin bed by wiping with a damp cloth & drying with a soft cloth.
Never clean with abrasives, chemical cleaners or household polishes.
Take care when handling or moving the Bed. Careless handling can damage wooden furniture.
Try to lift rather than drag.
If you have a problem with this product, please call our Customer Service Team who will be
glad to help.
We can usually provide replacement and / or spare parts promptly; it will help us if you can
identify the specific part using the check list in the next section.
Thank you for buying the Frooti Cabin bed
Before beginning assembly, please take a few minutes to read these instructions.
Lay the parts out on a clean, soft, flat surface (such as a carpeted floor) and compare with the
parts check list on the next page. Do not throw away any packaging until you are sure that you
have all the parts.
The product must be assembled by an adult. There are small parts so keep small children
away from the assembly area. Some stages of assembly require more than one person.
The recommended size of the mattress is 191cm x 90cm (6'3" x 3'0")
If, for any reason, you wish to return the product, you must disassemble the components and
use the original packaging.
Our Customer Service Number: 01985 300588
PLEASE READ CAREFULLY & KEEP FOR FUTURE REFERENCE
Frooti Cabin bed
Code: CBD001
2
lPeriodically check all fittings to ensure that none have come loose.
lKeep away from direct sources of heat, such as electric, gas or coal fires.
lDo not allow children to Climb on the furniture.
l Using this furniture other than for its intended purpose could cause damage
to the structure or serious injury to your child.
lThe Bed should not be used if any structural part is broken or missing.
lIf you can manage it, please try to persuade your children not to bounce on
the bed.
lWarning: The child`s bed should not be placed too close to other furniture or
windows, blind cords, curtain pulls or other strings or cords, and should be
placed either tight to any wall or have a gap of 300mm between the wall and
the side of the bed.

Parts Check List
3
11x Large Screws (35mm)
You will also need a screwdriver
16x Large Cam Pins
4x Small Cams (Drawer)
16x Large Cams
8x Small Screws (11mm)
4x Mounting Plates with screws
1x Allen Key
2x Rubber Buffers
Ends x2
Carcass Base x2
Side Rails x2
Mattress Base x1
Carcass Plinth x2 Carcass Back x2
Middle Brace x1
Shelf x1
Drawer Front x1
Drawer Sides x2 (Left & Right)
Doors x2
Drawer Base x1
Drawer Back x1
4x Drawer Castors
4x Hinges with screws
8x Bolts (15mm)
(Not supplied)
12x Dowels
Carcass Side x1
(Outside) Left Hand Side
Carcass Side x1
(inside) Left Hand Side
Carcass Side x1
(Outside) Right Hand Side
Carcass Side x1
(inside) Right Hand Side
4x Bolts (35mm)
4x Small Cam Pins (Drawer)
4x Euro Screws (15mm)
34x Large Screws (25mm)
4x Shelf Studs
4x Feet
Assembly
1. Preparing the carcass sides.
You need: 12x Cam Pins and a Screwdriver.
Place the Carcass Sides inside face up on a flat surface.
Insert 3x Cam Pins into the smaller holes in each side as shown below.
Repeat this assembly process for all four Carcass sides.
2. Attach the Carcass Base and Plinth to the sides.
You need: 12x large Cams, 4x Dowels and a Screwdriver.
Fit 2x Dowels into the ends of each Plinth. Align the Base and Plinth with the Sides and
engage the Cam Pins and Dowels. Flip the subassembly onto its back to make it easier to fit
the cams (shown below).
Insert 6x cams into the large holes on the bottom of each sub assembly, please ensure that
the arrow on the Cam is pointing towards the corresponding Cam Pin when inserted.
Once all is aligned and engaged, tighten the Cams clockwise with a screwdriver to secure the
structure. Repeat this assembly for the other side.
4
are pointing towards the Cam Pin
ensure arrows on Cams
When engaging,
Inner and Outer left hand Carcass Sides Inner and Outer Right hand Carcass Sides

5
3. Fit the Carcass Backs
Stand each sub assembly upright, insert a Carcass Back into each assembly (painted side
facing inwards), ensuring that each back correctly locates into the grooves on the Carcass
sides. Slide the back down so that it also engages into the grooves on the top of each Carcass
Base.
4. Attach the Middle Brace.
You need: 4x Cam Pins, 4x Large Cams and a Screwdriver.
Please Note: At this stage of the construction you should position the assembly as
close to its final position as possible. The assembly is difficult to move once fully built.
Insert 2x Cam pins into the small holes near the back edge on the outside face of each
Carcass Side. Ensure they are fitted on opposite sides as shown below.
Next insert 4x cams into the large holes on the back of the Middle Brace. Align and engage
the Brace onto the Cam Pins (as shown below).
Tighten the Cams clockwise with a screwdriver to secure.
4. Attach the ladder
5. Fit the Feet onto the Ends.
Insert 2x Feet into the Holes on the bottom edge of each End as below.
6. Fit the Shelf.
You need: 4x Shelf Studs.
Fit the 4x Shelf Studs into the holes on the outside faces of the two central Carcass sides,
ensure the Shelf Studs are orientated with the small peg on the flat side facing upwards.
Once the 4x brackets are in position carefully lift the shelf into the structure, ensuring that the
back of the shelf is pushed up against the front of the Middle Brace. Holes in the underside of
the shelf must also be correctly located onto the shelf studs.
7. Attach the End to the Assembly.
You need: 2x Bolts (35mm), 8x Bolts (15mm) and an Allen Key.
Please note: This stage of assembly should be attempted with a minimum of two
people to provide adequate support whilst parts are being secured together.
1: Align one End with the assembly so that the two holes containing metal inserts in the End
match up with the corresponding holes in the Carcass side, once aligned secure the End to
the Carcass side with the 2x Bolts (35mm) from the inside. (shown below).
2: At this stage also fit 4x Bolts (15mm) into each End as shown below. Ensure these Bolts are
only screwed in half way so that they are easier to locate onto the Brackets in the next stage
of assembly.
6
Insert 4x (15mm) Bolts into both Ends.
1
2

Slide Brackets
Downwards to
engage onto Bolts.
7
8. Attaching the Side Rails and End.
You need: 2x Bolts (35mm) and an Allen Key.
Fit the other End to the Carcass Side as before using the remaining 2x Bolts (35mm).
Attach the Side Rails to the Ends by fitting the pre-fitted Brackets over the Bolts (15mm) that
were fitted in stage 7. Fit the large ‘keyhole’ shaped holes in the Brackets over the exposed
heads of the Bolts at both Ends and lower each Side Rail downwards. Once the Brackets are
correctly engaged over each Bolt Head, fit 1x Euro Screw into the top small hole on the
Bracket and tighten the Bolts to secure the Rails as shown below.
& tighten the bolts
to secure the product.
Fit 1x Euro Screw
9. Fit the Doors.
You need: 4x Mounting Plates, 4x Hinges (complete with screws), 2x Rubber Buffers and a
Screwdriver.
Attach 4x mounting plates to the inside faces of the carcass sides using the pre- drilled pilot holes (See
Fig 9.1).
Please note: the mounting plates should be orientated with the Pre-fitted screw at the back.
Insert the door hinges into the large holes in the door and secure each using 16mm pre-fitted screws
(See Fig 9.2).
To attach the door, lift into position (See Fig 9.3) fit Hinge slot “A” over Bolt “B” and tighten Bolt “B”.
door adjustment may be made by slackening Bolt “B” slightly and either tightening or loosening screw
“C” as appropriate. Finally, re-tighten “B” and the screws holding the hinge mounts to the carcass side.
8
Fig 9.2 Fig 9.3
B
AC
Pre-fitted Screw towards the back
Fig 9.1
X
X
At this stage also fit 2x
rubber buffers (X) to the
inside face of the doors
ensuring that they are alined
with the front edges of the
carcass sides when the
doors are closed.

9
10. Assembling the drawer.
You need: 4x Small Cam Pins, 4x Small Cams, 4x Screws for Drawer Carcass (35mm) and a
Screwdriver.
Fit 4x Cam Pins into the Drawer Front. Place the two Drawer Sides onto each Drawer front
ensuring that all Cam Pins and pre-fitted Dowels are correctly engaged into their
corresponding holes and fit 4x Small Cams into each Drawer Side (as shown).
Insert the Drawer Back by slightly leaning the Drawer Sides outwards. Pre-fitted Dowels in
the Back must be located into the corresponding holes on the inside face of each Drawer
Side.
Note: The Cams that attach the Drawer Fronts to the Sides can be loosened to make it
easier to fit the Back.
Once in position, fit the 4x screws (35mm) as shown below to secure the Back to the Sides.
Dowel holes must face inwards
10
11. Drawer assembly continued.
You need: 7x Screws for Drawer Carcass (35mm) and a Screwdriver.
Ensure the Drawer frame is square and carefully fit the Draw Base. The lip on the Base
locates into the groove on the back of the Front. Once in position and all holes are aligned
correctly, secure the Base to the Drawer Frame using 7x Screws (35mm) (as shown below).

11
12. Attach the Castors.
You need: 8x Small Screws for Castors (11mm), 4x Castors and a Screwdriver.
Carefully turn the Drawer over and attach the 4x Castors to the Base with the 8x Screws
(11mm) as shown below. Finally turn the Drawer over and carefully slide it into the bed
Assembly.
13. Fit the Mattress Base.
You need: 34x Large Screws (25mm) and a screwdriver.
Carefully Lift the Mattress Base onto the Bed (webbing faced down) pull the Mattress Base up
to one End, then spread that slats out evenly. Use the 34x Large Screws to secure the base to
the bed through the holes in all slats.