Little Folks Furniture HSP003 User manual

Code: HSP003
Classic Hi Sleeper Bed

Treated properly it should be a faithful servant for years - and we hope you get the
same amount of pleasure from it. Before you do
lplease take a few minutes to read these instructions
lwe suggest you carefully unpack everything, lay it out on a clean, flat floor and
identify everything on the parts list in these instructions. Do not throw away any
packaging until you are sure you have all the parts.
If you have any problems assembling the product please call our customer services
on 01985 300588 and we will try and help. If for any reason you wish to return the
product, you must disassemble the product and pack in the original packaging.
Taking care of your product
Your furniture should require no more than a regular dust off with a soft cloth. If the furniture is
not painted then a superior wood polish can be used - but never use polishes containing
silicone.
If necessary it can be cleaned with a damp cloth with a mild detergent solution - and then
dried with a lint-free cloth. Never clean with abrasives or chemical cleaners.
Direct sunlight or heat from a radiator can stain, discolour warp or crack furniture.
We know furniture can be heavy but try not to drag furniture across the floor as this can
damage it.
Thank you for buying a
PRODUCT SAFETY
piece of furniture
If you have any problems please do contact us for help on e
mail [email protected] or phone our
CUSTOMER SERVICES 01985 300588
This product is designed to conform to BSEN747
The MAXIMUM thickness of the UPPER BUNK mattress is 20cm.
The recommended size of the mattress is 190cm x 90cm (6`3” x 3`0)
Periodically check that all assembly fixings are tightened properly, care should be
taken to ensure that no fittings are loose.
The furniture must be set up on an even and stable surface.
Keep away from direct sources of heat, such as electric, gas or coal fires.
Do not allow children to climb on the furniture. Using this furniture other than for its
intended purpose could cause damage to the structure or serious injury to your
child.
The Bunk should not be used if any structural part is broken or missing.
The upper Bunk is not suitable for children under six years old due to the risk of falls.
Do not attach items such as ropes, strings, cords, harnesses or belts etc to avoid the
risk of strangulation.
WARNING: Children can become trapped between the bed and the wall. To
avoid the risk of serious injury the distance between the top safety barrier and the
wall must not exceed 75mm or be more than 230mm.
This bed is designed to be fitted to a solid structure, e.g. a wall. This work should
only be carried out by a competent person or a professional.

M6x60 M6x35
2
Parts
Fittings
24
M6x100 M6x75
3
M6x60
2
M6x15
3
O10x12
26
O8x32
84
O7x50
9
1
Key 4 mm
O10x40
8
O3.0x30
40
A
C
B
D
1
2
3
4

Making the upper bed frame. (Two People)
44 x 35mm wooden dowels / 16 x 100mm bolts / 16 x barrel nuts.
Make end frames
Fit the two middle end rails and four top / bottom end rails with the small wooden
dowels (28) blind holes only (not the holes that have a side hole next to it)
Carefully position the four small legs using the numbers on the base of each leg to
orientate. Now make each bed end, left and right, carefully positioning the middle
end rails (without barrel nut holes) in the center. Align the 100mm bolts through the
bed legs positioning the barrel nuts inside the holes within the cross rails, rotate to
tighten.
Make the bed
Fit the four mattress rails with end dowels (16) into the blind holes.
Carefully orientate the mattress rails and safety rails as shown. Align the 100mm
bolts through the bed legs positioning the barrel nuts inside the holes within the rails,
rotate to tighten.
2
3
4
1
front mattress rail (with holes)
end rails (with holes)
Middle end rails (without holes)
end rails (with holes)
Middle end rails (without holes)
front mattress rail (no holes)
rear safety rails
Align
Tighten
Align
Tighten
Align
Tighten
Align
Tighten
(with holes) Middle rail (without holes)

Fit the mattres base (Two People)
34 wood screws
Gently roll out the mattress base (webbing side down) and lift it onto the mattress
rails supports (wooden pieces fitted to the inside of the mattress rails). Spread the
bed slats out to each end of the bed. Now screw each bed slat down using a
screw in each end, making sure the the end slats are tight to the bed legs at each
end, and that the bed remains parallel. (push gently inwards at the centre of both
mattress rails to maintain a uniform width)
X 34
Front of Bed (two holes in the mattress rail).
PUSH inwards
PUSH inwards

Making the lower bed frame. (Two People)
8 x Large wooden dowels /12 small wooden dowels, 6 x 100mm bolts, 6 x barrel
nuts
Fit the two cross rails and rear long rail with the small dowels (blind holes only).
Carefully identify the large legs by using the letters on the base of the part. Now
make up each frame end, aligning the legs (AB = left end/ CD = right end)
insert the 100mm bolts connecting through the barrel nuts and rotate to tighten.
Now connect the rear rail using the same principles.
Fit 8 x large wooden dowels into the top of the long leags, two per leg (tap
them down)
A
C
B
D

Making the Hi bed frame. (Two People)
8 x wood screws
Carefully lift the upper bed onto the lower frame, aligning the projecting
wooden dowels into the holes on the base of small bed legs. Once firmly
pressed down secure the joint by screwing them together, 2 screws per leg.

Make the ladder
8 x screw bolts, 16 x small wooden dowels
Fit the ladder treads (4) with the wooden dowels (4 per tread) using the outer
holes.
lay one ladder string down with the inside facing upwards (side with more holes
= inner face) and push the four treads into the matching holes. Once firmlly
pressed down, align and press fit the opposite ladder string. Now secure each
tread using the screw bolts, 2 per string.

Fit the ladder (two people)
3 x 75mm bolts, 3 x sleeve nuts, 1 x screw bolt
2 x 60mm bolts + 2 barrel nuts, 2 x 100m bolts + 2 barrel nuts, 8 x small wooden dowels.
At this point in the assembly you will need to decide which side the ladder is fitted, left or
right side of the bed.
Ladder left (Mirror assembly for right hand ladder)
Gently place the ladder up to the left side of the bed, with the ladder cut outs fitting over
the front mattress rail. Loosely connect the 3 x 75mm bolts through the out side of the left
bed leg assembly and into the left ladder leg, pushing in the 3 sleeve nuts into the
matching holes seen in the left hand ladder leg. Rotate to connect but do not tighten.
Now fit the 2 x shorter front safety rails with the wooden dowels (blind holes only) and align
and press fit into both the right hand bed legs and right hand ladder string (some light
flexing of the ladder string might be required here). Once together fit 2 x 60mm bolts
through the ladder string and 2 x 100mm bolts through the bed legs into the safety rails,
connect to barrel nuts and rotate to tighten. Not tighten the left hand ladder assembly.
Finally secure the ladder using the screw bolt from the inside of the bed into the right
hand ladder string.
75mm
75mm
60mm
100mm
Screw bolt
outside of bed
inside of bed

Fit the leg stabilzer
2 x 35mm bolts
This “leg stabilizer” is designed to be fitted to the inside of bed between the upper and lower
bed frames and on the opposite side to that of the ladder (see image)
Push the part into position and secure using the two bolts.
Inside of bed (opposite side to ladder)
35mm Bolt
35mm Bolt
Leg stabilzer

Connect the bed to a solid structure / wall
The bed is designed to be connected to a solid structure for extra stability.
Lift the bed into it`s final position. Using the two holes pre-drilled in the rear bed legs mark
out the drilling positions on the wall. Lift the bed away from the wall and make the holes,
making sure that you are using the correct wall fixings. Now re-align the bed, make good
the fixing and check that the bed is fitted securly to the wall.
No Fixings are provided as these will need to suit the wall type, and the length of the fixing will
depend on the wall material and any packers used to “bridge” the gap between the bed
and wall (skirting board). The two through leg holes should be adequate however further
anchor points may be required and this will depend on the bed position and wall (fixing
structure) make up.
This work should only be carried out by a compentent person or a professional.
Final check
Please position any storage furniture neatly under the upper bed as not to create ledges or
foot holds that might be used for access to the bed. Any furniture that is not used under the
bed should be individually fastened using the wall straps provided as to prevent toppling (see
their instruction leaflet). Carefull observation of safety gaps around your bed and furniture
should be maintained.
Do not attach items such as ropes, strings, cords, harnesses or belts etc to avoid the risk of
strangulation.
WARNING: Children can become trapped between the bed and wall, a roof pitch, the
ceiling, adjoining pieces of furniture (e.g. cupboards) and the like. To avoid risk of serious injury
the distance between the top safety barrier and the adjoining structure shall not exceed
75mm or shall be more than 230mm.
Wall
Skirting

Code: DSK007Edit Desk

Treated properly it should be a faithful servant for years - and we hope you get the same amount of pleasure from it. Before you dolplease take a few minutes to read these instructionslwe suggest you carefully unpack everything, lay it out on a clean, flat floor and identify everything on the parts list in these instructions. Do not throw away any packaging until you are sure you have all the parts. If you have any problems assembling the product please call our customer services on 01985 300588 and we will try and help. If for any reason you wish to return the product, you must disassemble the product and pack in the original packaging. Taking care of your product Your furniture should require no more than a regular dust off with a soft cloth. If the furniture is not painted then a superior wood polish can be used - but never use polishes containing silicone. If necessary it can be cleaned with a damp cloth with a mild detergent solution - and then dried with a lint-free cloth. Never clean with abrasives or chemical cleaners. Direct sunlight or heat from a radiator can stain, discolour warp or crack furniture. We know furniture can be heavy but try not to drag furniture across the floor as this can damage it. Thank you for buying a
PRODUCT SAFETYpiece of furnitureIf you have any problems please do contact us for help on e mail [e-mail] or phone ourCUSTOMER SERVICES 01985 300588Periodically check all fittings to ensure that none have come loose.Keep away from direct sources of heat, such as electric, gas or wood fires.Do not allow children to climb on the furniture. Larger items of furniture should be properly (and professionally) secured to the wall to prevent them toppling over. Little Folks Furniture do not supply wall fixings due to the wide ranging differences of wall construction.Warning: This work should only be carried out by a competent person or a professional.Using furniture other than for its intended purpose could cause damage to the structure or serious injury to your child. The furniture should not be used if any structural part is broken or missing.Do not place heavy or unsuitable sized items on the furniture due to risk of falling and injury.Place heavier items in the lower drawers or shelves.Remove all items from the upper surface when re-positioning as to eliminate the possibility of falling hazards.If used under an upper bed, align the furniture under the bed as notto generate projections which might be used as a foot-hold or ledge.

FittingsTools Req1 x Allen KeyPartsScrewdriver4 x Dowels2 x Cam Pins2 x Cam grub screw4 x Counter sunk BoltsCross railsupplied2 x Cams insertsTopDesk frame Desk frame Left-hand Right-hand 1 x Wall strap Kit

Fit the desk leg frames.2 x cam pinsScrew one cam pin into the metal insert positioned in the rear leg of each desk leg frame.Rotate Cam in up to shoulderFit the cross rail4 x dowels and 2 cam insertsInsert 2 dowels into the two outer holes at each end of the cross rail. Now fit the cam insert into the hole on the side of the cross rail making sure that the accepting hole is clear of wood chippings/detritus, carefully aligning the holes on the insert with the central end hole.Now repeat at the opposite end.Rotate Cam in up to shoulderCam insert hole MUST line up with central hole.Cross rail

View from the rear of the desk frame.Make the desk.4 x boltsWith the desk top resting on it`s back gently slide the desk frame into position, carefully aligning the holes on the desk top with the metal fittings seen in each leg frame. Once in position insert the bolts, once all four bolts are engaged, tighten the fittings. Orienate the desk onto the feet once finished.Box space on the right.Make the frame (ideally with two people)Carefully align and connect the cross rail to the desk frames (can be done one at a time). Once fully connected, insert the cam grub screw and rotate to tighten.

Fit the anti-topple deviceAnti-topple device (wall strap)Connect the strap to the rear of the desk and gently lift the desk into position.Placing the Desk IMPORTANTOrientate the desk with the back facing the wall. Extend the wall strap so it can touch the wall surface. Now mark the wall for the position of the wall fixing using the free hole within the strap. Gently lift the desk away from the wall to make a fixing that is suitable for the wall type you have. Re-position the desk and physically connect the desk to the wall.topIf you wish to “hide” the strap you can fix to the desk from the underside.Little Folks Furniture do not supply wall fixings due to the wide ranging differences of wall construction.This work should only be carried out by a competent person or a professional.

Final checkPlease ensure that the wall strap is connected to both the desk and a suitable wall structure. Check that all the fittings used to assemble the desk are fitted correctly and securely tightened.Check that the desk is positioned on a level floor and is secure and stable.

Code: STO005Storage Bookcasewith Beech Feet

Treated properly it should be a faithful servant for years - and we hope you get the same amount of pleasure from it. Before you dolplease take a few minutes to read these instructionslwe suggest you carefully unpack everything, lay it out on a clean, flat floor and identify everything on the parts list in these instructions. Do not throw away any packaging until you are sure you have all the parts. If you have any problems assembling the product please call our customer services on 01985 300588 and we will try and help. If for any reason you wish to return the product, you must disassemble the product and pack in the original packaging. Taking care of your product Your furniture should require no more than a regular dust off with a soft cloth. If the furniture is not painted then a superior wood polish can be used - but never use polishes containing silicone. If necessary it can be cleaned with a damp cloth with a mild detergent solution - and then dried with a lint-free cloth. Never clean with abrasives or chemical cleaners. Direct sunlight or heat from a radiator can stain, discolour, warp or crack furniture. We know furniture can be heavy but try not to drag furniture across the floor as this can damage it. Thank you for buying a
Periodically check all fittings to ensure that none have come loose.Keep away from direct sources of heat, such as electric, gas or wood fires.Do not allow children to climb on the furniture. Larger items of furniture should be properly (and professionally) secured to the wall to prevent them toppling over. Little Folks Furniture do not supply wall fixings due to the wide ranging differences of wall construction.Warning: This work should only be carried out by a competent person or a professional.Using furniture other than for its intended purpose could cause damageto the structure or serious injury to your child. The furniture should not be used if any structural part is broken or missing.Do not place heavy or unsuitable sized items on the furniture due to risk of falling and injury.Take care when using storage boxes or totes within the shelf spaces as part extention could cause instability to the main unit as well as increasing the risk of the boxes falling.Place heavier items on the lower shelves.Do not drag the unit due to risk of damage to the product and tipping.Remove all items from the upper surface when re-positioning as to eliminate the possibility of falling hazards.If used under an upper bed, align the furniture under the bed as notto generate projections which might be used as a foot-hold or ledge.PRODUCT SAFETYpiece of furnitureIf you have any problems please do contact us for help on email [e-mail] or phone ourCUSTOMER SERVICES 01985 300588