Little Folks Furniture Fargo HSP001 User manual

Code: HSP001

Treated properly it should be a faithful servant for years - and we hope you get the
same amount of pleasure from it. Before you do
lplease take a few minutes to read these instructions
lwe suggest you carefully unpack everything, lay it out on a clean, flat floor and
identify everything on the parts list in these instructions. Do not throw away any
packaging until you are sure you have all the parts.
If you have any problems assembling the product please call our customer services
on 01985 300588 and we will try and help. If for any reason you wish to return the
product, you must disassemble the product and pack in the original packaging.
Taking care of your product
Your furniture should require no more than a regular dust off with a soft cloth. If the furniture is
not painted then a superior wood polish can be used - but never use polishes containing
silicone.
If necessary it can be cleaned with a damp cloth with a mild detergent solution - and then
dried with a lint-free cloth. Never clean with abrasives or chemical cleaners.
Direct sunlight or heat from a radiator can stain, discolour warp or crack furniture.
We know furniture can be heavy but try not to drag furniture across the floor as this can
damage it.
Thank you for buying a
PRODUCT SAFETY
piece of furniture
If you have any problems please do contact us for help on e
mail [email protected] or phone our
CUSTOMER SERVICES 01985 300588
This product is designed to conform to BSEN747:1 2012
The MAXIMUM thickness of the UPPER BUNK mattress is 17cm.
The recommended size of the mattress is 191cm x 90cm (6`3” x 3`0)
Periodically check that all assembly fixings are tightened properly, care should be
taken to ensure that no fittings are loose.
The furniture must be set up on an even and stable surface.
Keep away from direct sources of heat, such as electric, gas or coal fires.
Do not allow children to climb on the furniture. Using this furniture other than for its
intended purpose could cause damage to the structure or serious injury to your
child.
The Bunk should not be used if any structural part is broken or missing.
The upper Bunk is not suitable for children under six years old due to the risk of falls.
Do not attach items such as ropes, strings, cords, harnesses or belts etc to avoid the
risk of strangulation.
WARNING: Children can become trapped between the bed and the wall. To
avoid the risk of serious injury the distance between the top safety barrier and the
wall must not exceed 75mm or be more than 230mm.

Fittings
Tools Req
Screwdriver
1 x Allen Key
Parts
2 x Universal Ends
rear holes
piece
4 x treads 1 x rear rail
1x mattress rail (ladder left)
2 x ladder pcs
4x Bolts 1.8cm
4 x Bolts 3.5cm
18 x Bolts 10cm
8 x Bolts 6cm
26 x Barrel Nuts
30 x Screws 3.2cm
2 x Screws 1.6cm
16 x Dowels
2x pads
2 x ladder hooks
1 x rear safety rail
1 x front safety rail
1 x mattress base
1x mattress rail (ladder right)

Making the bed frames.
12 x long Bolts 10cm, 12 x Barrel Nuts, an Allen key
Orientate the bed ends with the middle holes at the rear of the bed.
Push one barrel nut into each mattress rail holes, aligning the slot head to the end
hole.
Slide each bolt through the bed end holes and into the holes in the end of each
mattress rail.
Image with bed entrance on the right, if entrance required on the left, swap the
mattress rails. Twist the bolts to tighten the bed together.
Align
Tighten
rear safety
Mattress rail
Align
Tighten
rear safety
Mattress rail
Fit the rear rail
4 x long Bolts 10cm, 4 x Barrel Nuts, an Allen key
Orientate the rear rail with the holes on the edge upwards and insert 4 x barrel nuts.
Now insert 4 x bolts through the legs, rotating them into the barrel nuts. Tighten the
fittings
holes upwards

Fixing the front safety rail
You need: 2x 10cm bolts, 4 x 3.5cm bolts and an allen key.
Align the piece to the front mattress rail and fix directly into the mattress rail using 2
x 3.5cm bolts. Now insert 2 x barrel nuts into the front safety rail, slide 2 x 10cm bolts
through the leg opposite to the bed entrance and engage the rail. Insert 2 x 3.5cm
bolts through the piece and rotate into the front safety rail. Tighten all the parts up
using the allen key.
4 x 3.5cm
mattress base
Fit the mattress base
30 x 3.2cm wood screws
Spread out the mattress base onto both the bed frame, ensuring that the end slats
are tight up to the bed ends. Screw down each bed slat.

Make the ladder
You need: 8 x 6cm bolts, 8 x barrel nuts and 16 dowels
insert 4 x dowels into each tread
Orientate the ladder pieces so they are opposite each other and with the holes
facing upwards. Now press a tread into each pair of holes, matching the front
edges. Once all treads are engaged and the ladder formed, insert a barrel nut
into the tread hole, slip a 6cm bolt fom the outside, rotating into the barrel nut
hole, repeating on the remaining holes. Tighten all fixings to make the ladder.
4 x
Fit the ladder hooks
You need: 4 x bolts 1.8cm, 2 x ladder hooks and 2 x pads
Orientate the 2 x hooks on the ladder and connect using the 4 x 1.8cm bolts. Now
stick a pad onto the inside of the hook, this will protect the paintwork on your bed.
4 x

Fix the ladder to the bed
You need: 2 x 1.6cm screws
Fit the ladder into the bed entrance and screw the hooks to the bed rail.
2 x
Please refer to the individual instruction leaflets for the different
types of furniture that can be used with this bed.