Little Folks Furniture MSP001 User manual

Code: MSP001
Mid Sleeper Bed

Treated properly it should be a faithful servant for years - and we hope you get the
same amount of pleasure from it. Before you do
lplease take a few minutes to read these instructions
lwe suggest you carefully unpack everything, lay it out on a clean, flat floor and
identify everything on the parts list in these instructions. Do not throw away any
packaging until you are sure you have all the parts.
If you have any problems assembling the product please call our customer services
on 01985 300588 and we will try and help. If for any reason you wish to return the
product, you must disassemble the product and pack in the original packaging.
Taking care of your product
Your furniture should require no more than a regular dust off with a soft cloth. If the furniture is
not painted then a superior wood polish can be used - but never use polishes containing
silicone.
If necessary it can be cleaned with a damp cloth with a mild detergent solution - and then
dried with a lint-free cloth. Never clean with abrasives or chemical cleaners.
Direct sunlight or heat from a radiator can stain, discolour warp or crack furniture.
We know furniture can be heavy but try not to drag furniture across the floor as this can
damage it.
Thank you for buying a
PRODUCT SAFETY
piece of furniture
If you have any problems please do contact us for help on e
mail [email protected] or phone our
CUSTOMER SERVICES 01985 300588
This product is designed to conform to BSEN747:1 2012
The MAXIMUM thickness of the UPPER BUNK mattress is 15cm.
The recommended size of the mattress is 191cm x 90cm (6`3” x 3`0)
Periodically check that all assembly fixings are tightened properly, care should be
taken to ensure that no fittings are loose.
The furniture must be set up on an even and stable surface.
Keep away from direct sources of heat, such as electric, gas or coal fires.
Do not allow children to climb on the furniture. Using this furniture other than for its
intended purpose could cause damage to the structure or serious injury to your
child.
The Bunk should not be used if any structural part is broken or missing.
The upper Bunk is not suitable for children under six years old due to the risk of falls.
Do not attach items such as ropes, strings, cords, harnesses or belts etc to avoid the
risk of strangulation.
WARNING: Children can become trapped between the bed and the wall. To
avoid the risk of serious injury the distance between the top safety barrier and the
wall must not exceed 75mm or be more than 230mm.

1x Mattress Base
14 x Barrel Nuts
30 x Screws
Fittings
Tools Req
Screwdriver
2 x Allen Key
2 x Bolts 3.5cm
Parts
Right-hand side
Left-hand side
long ladder
short ladder
2 x tread
piece
front
2 x rear rails
1 x rear mattress rail
1 x front mattress rail
7x Bolts 4cm
14 x Bolts 6.5cm
4 x Bolts 8cm
2 x sleeve nuts

Making the bed frame. (Two People)
12 x Bolts 6.5cm, 12 x Barrel Nuts, an Allen key and a screwdriver.
Push one barrel nut into each mattress rail hole, aligning the slot head to the end
hole.
Slide each bolt through the bed end holes and into the holes in the end of each
rail.
Twist the bolts to tighten the bed together.
Align
Tighten
front mattress rail
rear mattress rail
front mattress rail
2 x rear rails
front bed leg (with metal inserts)
Making the ladder
At this point you need to decide which side the ladder is fitted (left or right)
4 x Bolts 8cm and an Allen key
Firmly push together the ladder treads into the ladder strings, notch to notch.
Insert 4 x bolts into the holes positioned at the rear of each ladder string, 2 each
side.
Twist the bolts to tighten the ladder together. (Some light movement can help with
engagement)
Ladder RIGHT
Ladder LEFT

2 x 3.5cm
2 x 4cm
2 x 6.5cm
Fit the front safety panel
2 x Bolts 6.5cm, 2 x barrel nuts and 2 Bolts 4cm an Allen key and screwdriver.
Insert 2 x 6.5cm bolts into the bed leg opposite to the ladder, insert 2 x barrel nuts
into the safety panel (holes on inside face). Now slide on the safety panel and
connect the panel to the long ladder leg using the 4cm bolts and the 6.5cm bolts
for the leg.
Twist the bolts to tighten the ladder to the bed.
Fit the Ladder (Right-hand entrance illustrated)
2 x Bolts 3.5cm, 2 Bolts 4cm an Allen key
Connect the short ladder to the bed leg using the 2 x 3.5cm bolts.
Now connect the long ladder to the mattress rail using 2 x 4cm bolts, inserting from
the inside of the bed frame.
Twist the bolts to tighten the ladder to the bed.
2 x 4cm

Fit the piece
3 x Bolts 4cm, 2 x Sleeve nuts an 2 Allen keys
Orientate the piece so that the holes line up with the rear rails. Now fit the 2 x
sleeve nuts into the top two rear rails. Use the 3 x 4 cm bolts to fix the piece from
the outside of the bed and into the 2 x sleeve nuts and lower mattress rail (metal
fixing already located in the rail).
Tighten with the 2 Allen keys to lock that parts.
Fix the base
30 x Wood screws and a screwdriver
Lift the slatted base onto the bed, slide out and screw down.
Note: Both end slats should be tight up to each bed end.
X 30
X 2
Now place the bed into position and place your furniture beneath the bed.