Little Folks Furniture BBD005 User manual

PLEASE READ CAREFULLY & KEEP FOR FUTURE REFERENCE
Code: BBD005
Classic Bunk Bed

Treated properly it should be a faithful servant for years - and we hope you get the
same amount of pleasure from it. Before you do
lplease take a few minutes to read these instructions
lwe suggest you carefully unpack everything, lay it out on a clean, flat floor and
identify everything on the parts list in these instructions. Do not throw away any
packaging until you are sure you have all the parts.
If you have any problems assembling the product please call our customer services
on 01985 300588 and we will try and help. If for any reason you wish to return the
product, you must disassemble the product and pack in the original packaging.
Taking care of your product
Your furniture should require no more than a regular dust off with a soft cloth. If the furniture is
not painted then a superior wood polish can be used - but never use polishes containing
silicone.
If necessary it can be cleaned with a damp cloth with a mild detergent solution - and then
dried with a lint-free cloth. Never clean with abrasives or chemical cleaners.
Direct sunlight or heat from a radiator can stain, discolour warp or crack furniture.
We know furniture can be heavy but try not to drag furniture across the floor as this can
damage it.
Thank you for buying a
PRODUCT SAFETY
piece of furniture
If you have any problems please do contact us for help on e
mail [email protected] or phone our
CUSTOMER SERVICES 01985 300588
This product is designed to conform to BSEN747:1 2012
The MAXIMUM thickness of the UPPER BUNK mattress is 20cm.
The recommended size of the mattress is 191cm x 90cm (6`3” x 3`0)
Periodically check that all assembly fixings are tightened properly, care should be
taken to ensure that no fittings are loose.
The furniture must be set up on an even and stable surface.
Keep away from direct sources of heat, such as electric, gas or coal fires.
Do not allow children to climb on the furniture. Using this furniture other than for its
intended purpose could cause damage to the structure or serious injury to your
child.
The Bunk should not be used if any structural part is broken or missing.
The upper Bunk is not suitable for children under six years old due to the risk of falls.
Do not attach items such as ropes, strings, cords, harnesses or belts etc to avoid
the risk of strangulation.
WARNING: Children can become trapped between the bed and the wall. To
avoid the risk of serious injury the distance between the top safety barrier and the
wall must not exceed 75mm or be more than 230mm.
WARNING:
Hole covers Not suitable for children under 36 months due to choking hazard.

Fittings
Tools Req
Screwdriver
2 x Allen Key
Parts
2 x mattress base
2 x ladder strings 2 x upper ends
2 x 7cm Bolts
2 x 6cm Bolts
1 x 3.5cm Bolts
7 x 5cm screw bolts
48 x small Dowels
4 x Large Dowels
2 x lower ends
3 x ladder treads
1 x upper front mattress rail
3 x mattress rails
2 x long safety rails
2 x front safety rails
14 x 9cm Bolts
16 x Barrel Nuts
76 x Screws 3.5cm
2 x sleeve nuts
4 x Hole covers
1 x upper front mattress rail
3 x mattress rails
2 x long safety rails

Fitting the rails
32 x small wooden dowels
Insert 2 wooden dowels into each end of each rail
X 1
X 3
X 2
X 2
Building the UPPER bed frame (Two people)
8 x 9cm bolts and 8 x barrel nuts
Build the bed with the parts positioned as shown, Locating the wooden dowels
into the holes on the two upper bed ends. Insert a barrel nut into the hole at
each end of the rails, allowing it to connect to a long bolt fitted from the outside,
rotate to tighten the bed frame
front rail (holes)
Align
Tighten
1 x upper front mattress rail
3 x mattress rails
2 x long safety rails
2 x front safety rails
2 X UPPER bed ends (holes in capping rails)

Building the LOWER bed frame (Two people)
4 x 9cm bolts and 4 x barrel nuts
Build the bed with the parts positioned as shown, Locating the wooden dowels
into the holes on the two upper bed ends. Insert a barrel nut into the hole at
each end of the rails, allowing it to connect to a long bolt fitted from the outside,
rotate to tighten the bed frame
Align
Tighten
2 X LOWER bed ends
x 34
x 34
Fix the mattress bases (Two people)
68 x wood screws
Gently lay the each mattress base out onto the support rails fitted to the inside of
the bed. Stretch the bases out so that the end slats are tight to the bed end
frames. Now screw down every mattress slat making sure the bed remains
parallel. Note; Upper bed = do not fix the last four bed slats on the end you
intend to fit the ladder.
x 34
Upper BunkUpper Bunk Lower Bunk

Make the bunk (two people)
4 x large wooden dowels and 8 x wood screws
Fit 4 x large wooden dowels into the top of the lower bed (holes in the capping rail
of the lower bed). Lift the upper bed onto the lower bed aligning the upper bed
onto the dowels. Once the bed frames are firmly togther, connect using the 8 x
wood screws.
Make the ladder
6 x 5cm screw bolts and 12 wooden dowels
Insert 12 wooden dowels into the 3 x ladder treads, 2 each end.
Align the 3 treads to match the holes in the two ladder strings, as seen.
Now press the parts together to form the ladder frame, inserting the screw bolts
from the outside.
Tighten using the allen key
upper front rail on same side as
ladder connection fitting

Fit the ladder
Ladder on left illustrated first followed by ladder on
right. (in two pages)
Fix 4 x wooden dowels into the left-hand ladder string
as shown.
Rotate the ladder
Gently engage the ladder notches over the
lower mattress rail and then push the left-hand
ladder string up against the bed legs, aligning
and engaging the wooden dowels
2 x 7cm bolts 2 x sleeve nuts
1 x 3.5cm bolt
Fix the front safety rails
2 x 6cm bolts, 2 x 9cm bolts and 4 x barrel nuts
Slide the two safety rails into the wooden
dowel holes. Now connect the two rails using
the bolts shown, rotating them tight through
the barrel nuts.
2 x 6cm bolts
2 x 9cm bolts
Connect the ladder string
2 x 7cm bolts, 2 x sleeve nuts and 1 x
3.5cm bolt
Fix the ladder string to the bed legs
using 2 x 7cm bolts and 2 x sleeve nuts
Connect the ladder to the lower bed
leg using the 3.5cm bolt
This can be a bit fiddly so do not
tighten up the upper fixings until you
have connected the lower 35mm bolt.

Secure the ladder
Connect the right-hand ladder string to the mattress rail using a 5cm screw bolt
from the inside. Move the mattress slats to allow access to bolt. Now fix the four
slats in place.
Position the bunk
Carefully lift the bunk bed into place using the lower bed ends (Two people)
Lift the mattresses upon the sleeping surfaces
Note than the upper mattress MAXIMUM thickness at 20cm
Please take a few minutes to look over the bunk bed to ensure that
the fittings are securely fastened and the product is stable.
Secure the ladder
Connect the right-hand ladder string to the mattress rail using a 5cm screw bolt
from the inside. Move the mattress slats to allow access to bolt. Now fix the four
slats in place.

Fit the ladder
Ladder right illustrations.
Fix 4 x wooden dowels into the right-hand ladder
string as shown.
Rotate the ladder
Gently engage the ladder notches over the
lower mattress rail and then push the right-
hand ladder string up against the bed legs,
aligning and engaging the wooden dowels
2 x 7cm bolts
2 x sleeve nuts
Connect the ladder string
2 x 7cm bolts, 2 x sleeve nuts and 1 x
3.5cm bolt
Fix the ladder string to the bed legs
using 2 x 7cm bolts and 2 x sleeve nuts
Connect the ladder to the lower bed
leg using the 3.5cm bolt
This can be a bit fiddly so do not
tighten up the upper fixings until you
have connected the lower 35mm bolt.
1 x 3.5cm bolt
Fix the front safety rails
2 x 6cm bolts, 2 x 9cm bolts and
4 x barrel nuts
Slide the two safety rails into the
wooden dowel holes. Now
connect the two rails using the
bolts shown, rotating them tight
through the barrel nuts.
2 x 6cm bolts
2 x 9cm bolts
Connect the ladder string
2 x 7cm bolts, 2 x sleeve nuts and 1 x
3.5cm bolt
Fix the ladder string to the bed legs
using 2 x 7cm bolts and 2 x sleeve nuts
Connect the ladder to the lower bed
leg using the 3.5cm bolt
This can be a bit fiddly so do not
tighten up the upper fixings until you
have connected the lower 35mm bolt.

Position the bunk
Carefully lift the bunk bed into place using the lower bed ends (Two people)
Lift the mattresses upon the sleeping surfaces
Note than the upper mattress MAXIMUM thickness at 20cm
Please take a few minutes to look over the bunk bed to ensure that
the fittings are securely fastened and the product is stable.
Secure the ladder
Connect the left-hand ladder string to the mattress rail using a 5cm screw bolt from
the inside. Move the mattress slats to allow access to bolt. Now fix the four slats in
place.

Conversion
Make two single beds (Convert the bunk)
Two people required.
Carefully remove the ladder and front safety rails. Now remove the wood screws
that hold the two bunks together and gently lift the upper bunk off the lower bunk,
placing on the floor. Remove the rear safety rails from the bed frame if you so wish.
Remove the large wooden dowels from the capping rails. You have the option to
cover these holes using the 4 x hole covers supplied.
Warning; We do not recommend that these hole covers are accessible to small
children of 36 months and under.
x 4
Please take a few minutes to look over the bunk bed to ensure that
the fittings are securely fastened and the product is stable.
Please keep any removed parts and fittings in a safe place for
future use.