Little Folks Furniture SBD008 User manual

Code: SBD008Fargo Day Bed

Treated properly it should be a faithful servant for years - and we hope you get the same amount of pleasure from it. Before you dolplease take a few minutes to read these instructionslwe suggest you carefully unpack everything, lay it out on a clean, flat floor and identify everything on the parts list in these instructions. Do not throw away any packaging until you are sure you have all the parts. If you have any problems assembling the product please call our customer services on 01985 300588 and we will try and help. If for any reason you wish to return the product, you must disassemble the product and pack in the original packaging. Taking care of your product Your furniture should require no more than a regular dust off with a soft cloth. If the furniture is not painted then a superior wood polish can be used - but never use polishes containing silicone. If necessary it can be cleaned with a damp cloth with a mild detergent solution - and then dried with a lint-free cloth. Never clean with abrasives or chemical cleaners. Direct sunlight or heat from a radiator can stain, discolour warp or crack furniture. We know furniture can be heavy but try not to drag furniture across the floor as this can damage it. Thank you for buying a
PRODUCT SAFETYpiece of furnitureThe recommended size of the mattress is 191cm x 90cm (6`3” x 3`0)Periodically check all fittings to ensure that none have come loose.Keep away from direct sources of heat, such as electric, gas or coal fires.Do not allow children to Climb on the furniture.Using this furniture other than for its intended purpose could cause damage to the structure or serious injury to your child.The Bed should not be used if any structural part is broken or missing.If you can manage it, please try to persuade your children not to bounce on the bed.Warning: The child`s bed should not be placed too close to other furniture or windows, blind cords, curtain pulls or other strings or cords, and should be placed either tight to any wall or have a gap of 300mm between the wall and the side of the bed.If you have any problems please do contact us for help on email [e-mail] or phone ourCUSTOMER SERVICES 01985 300588

2 x Mattress Rails1x Mattress Base32 x Screws FittingsTools ReqScrewdriver1x bed End (Left)Spanner12 x Dowels6 x Lunar WashersParts1x bed End (Right)1x Rear Panel6 x nuts6 x washers4 x 9cm Threaded Bar2 x 6cm Threaded Bar

9cm6cm9cm6cm9cm9cmMaking ready the bed ends.Lay both bed ends down on a soft carpet or use the internal packaging from the cartons as protection.Fitting the bed ends.4 threaded bars 9 cm, 2 threaded bars 6cm and 12 wooden dowelsInsert and rotate fully each threaded bar into the centre holes (metal inserts) on each bed leg (see images). Now insert the wooden dowels into the two holes either side of the fitted bars.9cmLeft-hand endRight-hand end

Making the bed. (Two people required)Starting from the rear, slide the mattress rail and rear panel onto the threaded bars and wooden dowels fitted in the bed legs on one bed end. Secure these two parts by carefully sliding the lunar washer onto the threaded bar as it passes through the large holes, adding the washer and finally the nuts. One person needs to hold and support while the front mattress rail is connected using the same process. Now very carefully align the remaining bed end with the two mattress rails and rear panel, supporting the ALL parts at the same time.The two mattress rails are fitted from the inside whereas the rear panel is secured from outside the bed.Rotate the nuts using the spanner provided and tighten the bed frame.Decorative featureRear of panel

Fix the base32 x Wood screws Lift the slatted base onto the bed, slide out and screw each slat down at each end.Note: Fit both end slats tight against the bed ends.X 32Position the bed and fit the mattress (Two people)Carefully lift the bed into position taking care not to drag.Gently lift the mattress onto the mattress base, tucking the mattress inside of the front mattress rail to secure.Refer to the trundle instruction leaflet for the assembly of the trundle bed.

Fit the trundle bed Assembly the trundle bed as explained in the trundle bed instruction leaflet.Now slide the trundle under the Day bed observing the gaps around the beds.Please take a few minutes to look over the bed to ensure that the fittings are securely fastened and the product is stable.

Code: TDL002

Treated properly it should be a faithful servant for years - and we hope you get the same amount of pleasure from it. Before you dolplease take a few minutes to read these instructionslwe suggest you carefully unpack everything, lay it out on a clean, flat floor and identify everything on the parts list in these instructions. Do not throw away any packaging until you are sure you have all the parts. If you have any problems assembling the product please call our customer services on 01985 300588 and we will try and help. If for any reason you wish to return the product, you must disassemble the product and pack in the original packaging. Taking care of your product Your furniture should require no more than a regular dust off with a soft cloth. If the furniture is not painted then a superior wood polish can be used - but never use polishes containing silicone. If necessary it can be cleaned with a damp cloth with a mild detergent solution - and then dried with a lint-free cloth. Never clean with abrasives or chemical cleaners. Direct sunlight or heat from a radiator can stain, discolour warp or crack furniture. We know furniture can be heavy but try not to drag furniture across the floor as this can damage it. Thank you for buying a
PRODUCT SAFETYpiece of furnitureIf you have any problems please do contact us for help on e mail [e-mail] or phone ourCUSTOMER SERVICES 01985 300588The recommended size of the mattress is 183cm x 76cm (6` x 2`6)Periodically check all fittings to ensure that none have come loose.Keep away from direct sources of heat, such as electric, gas or coal fires.Do not allow children to Climb on the furniture.Using this furniture other than for its intended purpose could cause damage to the structure or serious injury to your child.The Bed should not be used if any structural part is broken or missing.If you can manage it, please try to persuade your children not to bounce on the bed.Warning: The child`s bed should not be placed too close to other furniture or windows, blind cords, curtain pulls or other strings or cords, and should be placed either tight to any wall or have a gap of 300mm between the wall and the side of the bed.

3 x basesParts listFittingsTools ReqScrewdriver
1x Front Panel
16 x Fat Screws8 x Short Bolts 12 x Screws 4 x Rubber buffers4x Castor Pins 4x Castors 4x Castors
1x Rear Panel
2 x Sides4x BracketsSpanner (supplied)

Fit the Castors4 x castor pins, 4 x castors and the spanner.Screw the castor pins into the metal bushes that are fitted to the parts as shown. Once fully rotated into the bush, tighten with the spanner supplied. Now carefully push the wheeled castor onto the castor pin, you should hear a “click” when fully engaged.HereHereHereHereFit the Brackets16 x Fat screws and 4 x bed bracketsScrew the Brackets to the bed ends as shown.4 x Per End“Click”

Make the bed8 x short boltsInsert the short bolts into the 8 metal fittings in both the front panel and rear panel, rotating them in about halfway. Orientate the the parts so that the front is opposite the rear and with an end panel at each side.Start at one corner, slip one end part over the two short bolts fitted in the front panel, once over the heads, let the bracket drop down onto the shaft and tighten both bolts onto the bracket. Repeat the same process on the remaining corners.Note; the end panels are orientated so that the bracket is nearer to the top edge of the part.
Over and then downCompleted Bed Frame with ALL four corners made.12

Fixing the base12 x Wood screwsDrop the 3 x base boards into the bed and arrange so that the gaps between these parts are roughly equal. Now simply screw down each board until secure.Fit 2 x rubber buffers to the inside of the upper bed legs as this can help to protect the paint work on the bed and trundle sides.x 12 ScrewsFit 2 x rubber buffers to the inside of the trundle front, this will help protect the paintwork of your products. (Closing the trundle onto the bed mattress rail)Lay the mattress within the trundle and on the top of the base, or use the product as a storage unit.Push the trundle under the upper bed being aware of the gaps around the bed.Rubber buffer X 2Rubber buffer X 2