Little Folks Furniture SBD001 User manual

PLEASE READ CAREFULLY & KEEP FOR FUTURE REFERENCE
Code: SBD001
Edit Single Bed
FOD30323

Treated properly it should be a faithful servant for years - and we hope you get the
same amount of pleasure from it. Before you do
lplease take a few minutes to read these instructions
lwe suggest you carefully unpack everything, lay it out on a clean, flat floor and
identify everything on the parts list in these instructions. Do not throw away any
packaging until you are sure you have all the parts.
If you have any problems assembling the product please call our customer services
on 01985 300588 and we will try and help. If for any reason you wish to return the
product, you must disassemble the product and pack in the original packaging.
Taking care of your product
Your furniture should require no more than a regular dust off with a soft cloth. If the furniture is
not painted then a superior wood polish can be used - but never use polishes containing
silicone.
If necessary it can be cleaned with a damp cloth with a mild detergent solution - and then
dried with a lint-free cloth. Never clean with abrasives or chemical cleaners.
Direct sunlight or heat from a radiator can stain, discolour warp or crack furniture.
We know furniture can be heavy but try not to drag furniture across the floor as this can
damage it.
Thank you for buying a
PRODUCT SAFETY
piece of furniture
If you have any problems please do contact us for help on
email [email protected] or phone our
CUSTOMER SERVICES 01985 300588
This product is designed to conform to BSEN747:1 2012+A1:2015
The MAXIMUM thickness of the UPPER BUNK mattress is 23cm.
The recommended size of the mattress is 190cm x 91cm (6`3” x 3`0)
Periodically check that all assembly fixings are tightened properly, care should be taken to
ensure that no fittings are loose.
Always follow the manufacture`s instructions.
Please ensure that good ventilation is maintained within the room in order to keep humidity
low and to prevent mould in and around the bed;
WARNING “High beds and the upper bed of bunk beds are not suitable for children under six
years due to the risk injury from falls”.
WARNING “Bunk beds and high beds can present a serious risk of injury from strangulation if
not used correctly. Never attach or hang items to any part of the bunk bed that are not
designed to be used with the bed, for example, but not limited to ropes, strings, cords, hooks,
belts and bags”
WARNING “Children can become trapped between the bed and the wall, a roof pitch, the
ceiling, adjoining pieces of furniture (e.g. cupboards) and the like. To avoid risk of serious
injury the distance between the top safety barrier and the adjoining structure shall not
exceed 75mm or shall be more than 230mm.
WARNING Do not use the bunk bed if any structural part is broken or missing;
WARNING Hole covers Not suitable for children under 36 months due to choking hazard.
The recommended size of the mattress is 191cm x 90cm (6`3” x 3`0)
Periodically check all fittings to ensure that none have come loose.
Keep away from direct sources of heat, such as electric, gas or coal fires.
Do not allow children to Climb on the furniture.
Using this furniture other than for its intended purpose could cause damage to the
structure or serious injury to your child.
If you can manage it, please try to persuade your children not to bounce on the
bed.
Always follow the manufacture`s instructions.
Warning: The child`s bed should not be placed too close to other furniture or
windows, blind cords, curtain pulls or other strings or cords, and should be placed
either tight to any wall or have a gap of 300mm between the wall and the side of
the bed.
WARNING: Do not use the bed if any structural part is broken or missing;
Please ensure that good ventilation is maintained within the room in order to keep
humidity low and to prevent mould in and around the bed.

Fittings
Tools Req
Screwdriver
1 x Allen Key provided
Parts
4 x Barrel Nuts
4 x Large Bolts 9cm
34 x Screws 3cm
1 x small bed panel 1 x large bed panel
1 x mattress base
8 x Small Dowels
1x large leg Right
1 x large leg Left
1 x small leg Left
1 x small leg Right
2 x mattress rails
small hammer

Fit the bed panels
You need:
Lay each bed panel onto the floor ( use packaging material to protect the parts)
and gently insert (tap) the wooden dowels into the blind holes positioned on the
bed panel edges ,as shown. Now gently insert the cam sleeves into the large holes
on the flat face of each bed panel, orientating the internal holes.
8 x wooden dowels & 8 cam sleeves
Cam sleeve
X = curve on outer edge
X
X
X
Fit the bed legs
You need: 12
Lay the bed legs out carefully pairing up the legs using the outer curve on the legs
as a reference. Screw a cam pin into each of the metal inserts located in the leg
slot. Note that the cam pins need to have the eyelet hole at 90 degrees to the
long leg edge, see diagram (the pins do not need to be screwed down tight, the
alignment is more important).
x cam pins
bed panel edge
X
PAIR PAIR

Making the large bed end
6 x cam grub screws
Align the large bed panel (panel with holes upwards) with the pair of large bed
legs observing the position of the bed legs outer edge curves. Push the parts
together. Now insert the cam grub screws into the cam sleeves and tighten down
once aligned. Note ; if the bushes do not tighten check cam pin hole is facing
upwards, rotate cam pin on the leg if required.
2 x small bed ends
rotate Cam grub screw into the cam sleeve and tighten
Push inwards
rotate Cam bush into the cam sleeve and tighten
2 x small bed ends
Push inwards
curve on bed leg
curve on bed leg

rotate Cam grub screw into the cam sleeve and tighten
curve on bed leg
Making the small bed end
6 x cam grub screws
Align the small bed panel (panel with holes upwards) with the small bed legs
observing the position of the bed legs edge curves. Push the parts together,
inserting the cam grub screws into the cam sleeves and tighten down once
aligned. Note ; if the bushes do not tighten check cam pin hole is facing upwards,
rotate cam pin on the bed legs required.
curve on bed leg

Fitting the Rails
8 x small wooden dowels
Insert 2 wooden dowels into each end of each rail.
Gently tap dowels inwards until firmly in place.
Making the bed frame.4 x long Bolts 9cm, 4 x Barrel nuts ( two people)
Select the large and small bed frames and both mattress rails, orientating the
mattress rails with the inner support piece at the bottom.
Align the mattress rails with the dowels locating into the two bed leg holes, inserting
the 9cm bolt centrally from the outside of the bed frame, engaging the barrel nut
fitted from the inside.
Align
Tighten
fitted insidefitted inside
Push rails inwards
fitted insidefitted inside

x 34
Push inwards
S ome “light” inward pressure on the rails
b efore screwing down the mattress base
This helps keep the bed parallel
Push inwards
Fit the bed mattress base
34 x screws
Carefully roll out the mattress base onto the mattress support pieces fitted on the
inside of the mattress rails, webbing on the underside. Starting at one end of the
bed, push the end lath tight up against the bed legs and screw in place using
the two end holes in the lath. Now push the other end lath tight up against the
bed legs at the opposite end of the bed, screwing down to secure. Once both
ends of the base are fitted, position yourself at the centre of the bed, now fix
each end of the central lath making sure that the lath is tight against the both
mattress rails( some gentle inward pressure will help). Once these three laths are
fixed, secure the remaining base laths, screwing down each lath in turn.
Push Inwards
Push Inwards
Some “light” inward pressure on both rails before screwing down the bed laths
helps keep the bed parallel
Fit the mattresses.( two people)
Carefully lift the mattress onto the sleeping surface.
Please use the correct sized mattresses for this product.

Additional information
Periodically check that all assembly fixings are tightened properly, care should be taken to
ensure that no fittings are loose.
Always follow the manufacture`s instructions.
Please ensure that good ventilation is maintained within the room in order to keep humidity
low and to prevent mould in and around the bed;
WARNING Hole covers Not suitable for children under 36 months due to choking hazard.
The bed can be dismantled for storage or transportation.
Children are likely to play, bounce, jump and climb on beds, therefore the child`s bed should
not be placed too close to other furniture or windows, blind cords, curtain pulls or other strings
or cords and should be placed either tight to any wall or have a gap of 300mm between the
wall and the side of the bed.
Additional or replacement parts should be obtained from Little Folks Furniture.
WARNING Do not place this child`s bed near heat sources, windows and other furniture.
WARNING Do not use this child`s bed if any part is broken, torn or missing.
PRODUCT SAFETY
Moving the bed
Do Not drag or twist the bed.
Lift the bed into place by supporting both the end bed frames and mattress rails,
keeping the bed assembly all together and in unison. Removing the mattress will
help reduce the overall weight of the bed.