GB
Unpacking
11
Installing the Base Stand
33
Operating Your Remote Control
22
Connecting the Aerial
44
Turning the TV On for the First Time
66
Connecting to the Mains Socket
55
Target Region Descriptor
77
L22FE12
L24FE12
Connect one end of the RF coaxial cable to the aerial socket on the
wall and the other end of the cable to the RF (75Ω) socket at the rear
right side of your TV.
Do not connect the TV to the mains supply until you
have completed all the connections.
1. Connect the mains cable to the mains socket after you have
completed all the connections.
2. At this stage, the TV switches to standby mode. The red LED
indicator will illuminate on the front panel of the TV.
3. In standby mode, press the button on the right side panel of the
TV or on the remote control to turn the TV on. The red LED
indicator will turn blue.
To mains
socket
Remove all packaging from the TV. Retain the packaging.
If you dispose of it please do so according to any local
regulations.
Make sure the (+) and ( – ) ends
of the batteries match the (+)
and ( – ) ends indicated in the
battery compartment.
1. Press and lift the back cover to open the
battery compartment of the remote
control.
2. Insert two AAA size batteries. Close the
battery compartment cover.
1. Lay the TV down on a flat surface with the back side facing up. Please make sure a soft cushioned material (such as a pillow or thick piece of foam) is
placed beneath the screen.
2. To install the TV stand, first attach the stand support to the TV by using screw A. Align the screw hole then use screw A to fix the stand support to the TV.
3. To install the base stand, align the screw hole, then secure with a screw driver (not included) using the screw B provided.
screw
screw
Quick Start Guide
Thank you for purchasing your new Logik TV.
Your new TV incorporates the latest technology to enhance your
viewing experience. We would suggest that you allow about 20
mins for initial setup.
Please follow this guide for a successful first time installation.
22” / 24” Full HD LED TV
USB HDMI2 HDMI1 PC IN RF
COMMON INTERFACE (CI)
HEADPHONE PC AUDIO
RF Coxial Cable
(not included)
OR
Screw A x 1
(P.N.: 209100422B1)
Screw B x 1
(P.N.: 20912223101)
TV Front
Base Stand
Front
Target Region Setting
Country Code GBR
Primary Region England
Secondary Region
Tertiary Region
London
During tuning your TV may have received signals
from more than one transmitter. If this has occurred
the Target Region Descriptor screen will be
displayed. This will enable you to select the correct
regional transmission for the local news service that
you require.
Press the buttons to adjust each option's setting
and then press the OK button to confirm.
This will be shown as GBR for the UK.
This will show the regional country
(e.g. England, Wales, Scotland, NI).
This will allow you to set the region for
your local news service.
You may receive signals from more than
one transmitter within the Secondary
Region, (e.g Beds and Cambs may have
Luton or Sandy Heath).
First Time Installation
Please ensure aerial is plugged in!
Then press OK button.
France
Greece
UK
Australia
Austria
Czech
Denmark
Finland
Country
OK
Belgium
Bulgaria
Croatia
Hungary
Italy
Luxembourg
Germany
Channel Tuning
TV : 3 Channel(s)
DTV : 0 Channel(s)
Radio : 0 Channel(s)
Data : 0 Channel(s)
36%... 668.75 MHz (TV)
Please press MENU to skip.
Dansk
Deutsch
Hrvatski
Italiano
OSD Language
OK
Magyar
Nederlands
Norsk
PolskiEnglish
Cesky
E k
Espanol
~
Fran ais
Portugues
Pycck
(P.N.: 4033C226119)
Well done, your new TV is now ready to use. You will find that there are many exciting features available. To get to know all these
features, please take some time to read the instruction manual provided with your TV.
If after reading the instruction manual you have additional questions related to the use of your TV please call our UK Call Centre on 0844 561 1234.
Our UK Customer Contact Centre is open Monday-Saturday 8am-8pm or Sunday 8am-6pm.
The first time you turn the TV on, it will go straight into First Time Installation menu.
1. Press the OK button to
start First Time
Installation menu.
4. Channel tuning will
commence. This operation
may take up to 6 minutes.
The display will show the
progress of the tuning and
the number of channels
found.
2. Press the buttons
to select English as your
desired language to be
displayed on the menu.
Press the OK button to
confirm.
3. Press the
buttons to select UK as
the country where you
will operate the TV.
Press the OK button to
confirm.
TV
TV Stand Support
Quick Start Guide
TV Base
Remote Control /
AAA Batteries x 2
Instruction Manual
Screw A x 1
Screw B x 1
L22_24FE12_QSG_Running Change_120816_Annie.pdf 1 12年8月16日 下午2:31
