Logik L22FE14 User manual

Connecting the Aerial and the Mains Socket
44
Turning the TV On for the First Time
55
Target Region Setting
66
Quick Start Guide
Thank you for purchasing your new Logik TV.
Your new TV incorporates the latest technology to enhance your viewing experience. We would suggest that you allow about 20 mins for initial setup.
Please follow this guide for a successful rst time installation.
The latest eco-friendly power-saving technology will switch off the TV if
device is left on and idle for 4 hours. Please refer to “Auto Standby” under
the “Time Settings” section of the instruction manual for more detail.
Unpacking
11
Installing the Base Stand
33
Operating Your Remote Control
22
Do not connect the TV to the mains supply until you
have completed all the connections.
Target Region Setting
Country Code GBR
Primary Region England
Secondary Region
Tertiary Region
London
During tuning your TV may have received signals
from more than one transmitter. If this has occurred
the Target Region Setting screen will be displayed.
This will enable you to select the correct regional
transmission for the local news service that you
require.
Press the buttons to adjust each option's setting
and then press the OK button to confirm.
This will be shown as GBR for the UK.
This will show the regional country
(e.g. England, Wales, Scotland, NI).
This will allow you to set the region for
your local news service.
You may receive signals from more than
one transmitter within the Secondary
Region, (e.g Beds and Cambs may have
Luton or Sandy Heath).
Well done, your new TV is now ready to use. You will find that there are many exciting features available. To get to know all these
features, please take some time to read the instruction manual provided with your TV.
If after reading the instruction manual you have additional questions related to the use of your TV please call:
• UK Call Centre on 0344 561 1234. • Ireland Call Center on 1 890 818 575.
The first time you turn the TV on, it will go straight into First Time Installation menu.
First Time Installation
Please ensure aerial is plugged in!
Then press OK button.
OK
UK
Sweden
France
Ireland
Finland
Spain
Denmark
Portugal
Norway
Country
TV : 0 Channel(s)
Channel Tuning
DTV : 3 Channel(s)
Radio : 0 Channel(s)
Data : 0 Channel(s)
36%... 668.75MHz (DTV)
Press MENU to skip.
OK
English
Svenska
Dansk
ýesky
Slovak
Norsk
Suomi
Please select an OSD Language
OK
Home Mode
Shop Mode
Mode Select
1. Press the OK button to start
First Time Installation menu.
2. Press the buttons to
select your desired language
to be displayed on the menu.
The default on-screen menu
language is set as English.
Press the OK button to
confirm.
3. Press the buttons to
select your desired mode and
then press the OK button.
Press the button to select
Yes to confirm or the button
to select No to cancel and
return to the Mode Select
menu.
4. Press the buttons to
select the country where you
will operate the TV. Press the
OK button to confirm.
5. DTV channel tuning will
commence. This operation
may take up to 3 minutes. The
display will show the progress
of the tuning and the number
of channels found.
Remove all packaging from the TV. Retain the packaging.
If you dispose of it please do so according to any local
regulations.
Make sure the (+) and ( – ) ends
of the batteries match the (+)
and ( – ) ends indicated in the
battery compartment.
1. Press and lift the back cover to open
the battery compartment of the remote
control.
2. Insert two AAA size batteries. Close the
battery compartment cover.
screw in
screw in
Screw A x 1
Screw B x 3
TV
Front Base Stand
Front
TV
TV Stand Support
Instruction Manual
Quick Start Guide
TV Base
Remote Control /
AAA Batteries x 2
Screw A x 1
Screw B x 3
1. Lay the TV down on a flat surface with the back side facing up, and ideally at the edge of a table so that the base of the TV slightly overhangs on it.
Please make sure a soft cushioned material (such as a pillow or thick piece of foam) is placed beneath the screen.
2. To install the TV stand, first attach the stand support to the TV by using screw A. Align with the screw hole then use screw to fix the stand support to
the TV.
3. To install the base stand, align the screw hole, then secure with a screw driver (not included) using the 3 screw B provided.
22” LED TV
L22FE14
1
2
USB HDMI2 HDMI1 PC IN RF
COMMON INTERFACE (CI)
HEADPHONE PC AUDIO
To mains socket
RF Coxial Cable
(not included)
OR
1. Connect one end of the RF coaxial cable to the aerial
socket on the wall and the other end of the cable to the RF
(75Ω) socket at the rear right side of your TV.
2. Connect the mains cable to the mains socket after you
have completed all the connections.
3. At this stage, the TV switches to standby mode. The red
LED indicator will illuminate on the front panel of the TV.
4. In standby mode, press the button on the right side
panel of the TV or on the remote control to turn the TV on.
The red LED indicator will turn blue.
(QSG-L22FE14-140519V2)
If you select Ireland as the country where you will operate the
TV, a pop-up screen will be display. You will need a 4-digit
activation code for Irish tuning. This code can be found
in-store, on the back of your receipt (if bought in Ireland), or
call the customer service team / KNOWHOW.
L22FE14_QSG_RC140519_Annie.pdf 1 19/5/14 9:55 am