LogTag UTRED30-16 User manual

Version F - September 2021
www.logtagrecorders.com
Quick Start Guide

What's Included 3
Downloading LogTag Analyzer 4
Configuring your UTRED30-16 5
Starting your UTRED30-16 6
During Recording 8
Downloading Results 9
Quick Start Guide Contents

Page 3
What's Included
Please check you have each of the items shown below
before continuing with setting up your UTRED30-16.
UTRED30-16
USB Cable AC Adapter
Sensor
Cover
(Optional
to Use)
2x AAA Battery
(Not included)
Glycol Buffer
(Not included)
UTRED30
Wall mount
(Not included)
External Probe/s
(Not included)

Page 4
Downloading LogTag
Analyzer
To download the latest LogTag Analyzer, open your
browser and navigate to:
https://logtagrecorders.com/software/LTA3/
1. Click ‘Go To Downloads Page’ button
2. Click ‘Download Now’ to start the download
3. Click ‘Run’ or ‘Save File’ then double-click the
downloaded file to open Analyzer Setup Wizard
4. Once the Analyzer Setup Wizard is open, follow
the on-screen prompts to install Analyzer onto your
computer
5. Click ‘Finish’ to exit the Setup Wizard
Warning: Please ensure no other LogTag software is
currently running on your computer before running the
Analyzer software.

Page 5
Configuring your
UTRED30-16
Connect your UTRED30-16
to your computer via the USB
cable provided. The USB
socket on the device is located
on the bottom, protected by a
rubber seal.
1. Open LogTag Analyzer
2. Click ‘Configure’ from the ‘LogTag’ menu or click
the ‘Wizard’ icon. Please select which Channel(s) you
wish to log, in ‘Log channels:’ setting.
3. Adjust your logger configuration settings as
required. For more information on configuration
settings, please refer to Configuring the UTRED30-16
in the Product User Guide or press ‘F1’ for help from
your keyboard
4. Click ‘Next’ to upload the configuration settings to
the logger
5. Click ‘Close’ to exit the configuration page
Note: Please ensure you have LogTag Analyzer
version 3.1.15 onwards for configuration of the
UTRED30-16 dual-sensor models.

Page 6
Starting your UTRED30-16
Press and hold the
START/Clear/Stop button.
STARTING will appear
along with READY.
Release the button once
READY disappears.
The UTRED30-16 now
records temperature
data.
The Logger will not start
if:
• You release the
button before READY
disappears.
Before starting, please ensure you have connected
the ST100X external probe(s) into the correct Channel
sensor port(s) you have configured to record from.
Before startin
g
, please ensure you have connected
the ST100X external
p
robe(s) into the correct Channel
sensor port
(
s
)
you have confi
g
ured to record from
.

Page 7
Starting your UTRED30-16
(continued...)
• You keep holding the
button for more than 2
seconds after READY
disappears.
• The backup battery is
critically low and the
logger is not connected
to power.
Press the CHANNEL
button to change the
channel on screen.
In this example, the
display switched from
CH1 to CH2.
Note: The sensor cover can be inserted in an unused
sensor port.

Page 8
During Recording
To view more information about clearing alarms and
resetting and reviewing trip statistics, please refer to
the Product User Guide.
End of page

Page 9
Downloading Results
Alternatively, you can follow the steps below:
1. Open LogTag Analyzer
2. Click ‘LogTag’ from the ‘Download’ menu or press ‘F4’
3. Click ‘Close’ to exit the download page
Connect your UTRED30-16 to
your computer via the USB cable
provided. The USB socket on the
device is located on the bottom,
protected by a rubber seal.
A new device drive will appear in file explorer with the
files containing the recorded data for the Channel(s)
monitored.
By default, auto-download is enabled in LogTag Analyzer
so when you open the program, data results will be
displayed after connecting your UTRED30-16 to your
computer