Label
Pay attention to adjusting the
eccentric nut to prevent the
roller from being damaged
by the groove.
Add an isolated cylinder。
2
3
4
Preparation:
X-Axis Frame, and the frame to complete the assembly.
6
7
Connect the cable to the motor, limit switch and the laser head as shown in the figure.
Preparation:
Limit switch x2, Timing belt x2, M5 T-shaped
nut x4, M5*6 round head screw x4.
INSTALLATION STEPS
1
T-shaped Screw
M5*6
Install the X-Axis Frame in the V-groove of the left and
right Frames along the direction of the arrow.
Place the profiles on a flat table in order, and place four corner grooves into the
profiles referring to diagram.
Tighten the M5*25 screw with M5 washer into frames.
Tighten the M5 screws on the corner grooves.
According to the figure, install the supporting foot,
the control box of the engraving machine, and the
left profile limit screw in the corresponding position.
Note: Fix the cable to the sheet metal with cable ties where there is tape, and then move
the laser head to the upper right corner to confirm that the cable has sufficient length.
Focusing:
Place the engraver or cutting material under the engraving head, and put the focus plate
on the material, then loosen the thumb screw to let the laser module touching the focus
plate, tighten the thumb screw to lock the laser module.
1. Place a timing belt along the red arrow with the tooth face down.
2. Put the T-shaped nut on one end of the belt , use an L-shaped screwdriver to rotate the
T-shaped nut, then screw in the M5*6 screw to fix one end of belt.
3. Tighten the belt by hand, then fix another end of belt in the manner of previous step.
4. Fix another belt on left frame in the same way.
For installation details,
please watch the
video "RAY5 Quick
Start Guide" in the
Micro SD card.
Preparation:
Preparation: Support feet x3, engraving machine
control box, M5*16 hexagon socket cup head screw
x8, M5*8 hexagon socket round head screw x1,
nylon isolation column (7*5*6) x1.
Left side frame
with limit screw.
M5*16
Note: Do not obstruct the movement stroke of the engraving
machine with the round head screws
M5*8
Please reference more details on digital manual in TF card about the operation of
Laser Engraver and installation of LaserGRBL or LightBurn.
5
M3*6
Put the M5 flat washer on the thumb screw, use thumb screw to fix the laser module.
Note: The thumb screw of RAY5 20W is M5*8, while the screw of RAY5 5W or 10W is M5*10,
so the screw of RAY5 5W or 10W cannot be used on RAY5 20W, and it needs to be installed
with M5 flat washer, otherwise the screw will interfere with the X-axis limit switch.
Use a wrench to fix the M3*6 round head screw, please be careful not to lock the screw,
otherwise the laser module cannot be moved up and down.
Preparation:
Laser module, M5X8 thumb screw x2, M5 flat washer x2,
M3x6 round head screw x2.
Thumb Screw
1
2
3
4
Timing Belt
Limit Switch
5. Turn the RAY5 engraver over, attach the X limit switch to the edge of the label, and fasten it with
a hex key allen wrench, then limit switch is about 33mm from the left sheet metal.
6. Attach the Y limit switch to the edge of the label, and fasten it with a hex key allen wrench, then limit
switch is about 72mm from the right sheet metal.
Label
33mm
72mm
Note: Please install the limit switch attached with label, otherwise it will affect the engraving size or
cause the laser head module to collide with the profile when homing.
Laser Module
M5 Flat Washer
Focus Plate
