Lorex L19LD800 Series User manual

BUSINESS & HOME SECURITY
INFORMATION IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. AS OUR PRODUCTS ARE SUBJECT TO CONTINUOUS IMPROVEMENT,
LOREX TECHNOLOGY INC. AND OUR SUBSIDIARIES RESERVE THE RIGHT TO MODIFY PRODUCT DESIGN, SPECIFICATIONS AND PRICES, WITHOUT
NOTICE AND WITHOUT INCURRING ANY OBLIGATION. E&OE © 2007 LOREX. ALL RIGHTS RESERVED.
L19LD800Series
WWW.LOREXCCTV.COM
QUICK START GUIDE R2

Page: 2
L19LD800 SERIES QSG_EN_R2
www.lorexcctv.com
Page: 2
PACKAGE CONTENTS AND
INSTALLATION GUIDE:
ATTENTION:
Broadband Router
and Computers are
required for local and
remote monitoring
(not included).
INSTRUCTIONS:
For detailed setup
information, please
refer to your User’s
manual.
SOFTWARE
REQUIREMENTS:
For Lorex Client 3.0
Software requirements,
please refer to the
Software User’s manual.
System Contents:
1 - 19” 8 Channel LCD Monitor with pre-installed HDD*
4 - High Res. Color Cameras*
4 - 100 ft (30M) Extension Cables*
4 - Camera Stands with Mounting Screws*
1 - 10 ft Ethernet Cable
1 - Remote Control
2 - AAA Batteries
1 - Power Adaptor (for monitor)
1 - Lorex Client Software CD
1 - User’s Manual
1 - Software Manual
1 - Quick Start Guide
* Camera configuration and HDD (hard disk drive) capacity may vary
by model. BNC Cameras require individual power adaptors. Check
your package for specific content information.
INSTALLATION GUIDE
Skill Level
Intermediate
easy advanced
Time
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
Skill Level
Intermediate
easy advanced
Time
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
Time Tools Skills - Easy
Under 20 Minutes* Hand Tools Plug & Play connectors,
On screen set up
* Installation time may vary based on
application and camera cabling
STEP 1 STEP 2
Skill Level
Intermediate
easy advanced
Time
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
Time Skills - Intermediate
Plug & Play connectors,
On screen set up
Under 30 Minutes*
* Installation time may
vary based on application
Skill Level
Intermediate
easy advanced
Time
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
Hardware
Computer &
Router*
STEP 3
Skill Level
Intermediate
easy advanced
Time
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
Skill Level
Intermediate
easy advanced
Time
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
Time Hardware Skills - Advanced
60 Minutes Computer &
Router*
Basic Computer
Skills, Router Port
Forwarding
* Installation time may vary
based on application
Skill Level
Intermediate
easy advanced
Time
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
* Minimum System Requirement: Windows XP, Pentium IV,
256MB Ram (512MB Recommended), 200MB Storage, High
Speed Internet, DSL or Cable Modem


Check Pages
14 - 15

Page: 2
Page: 2Page: 3
L19LD800 SERIES QSG_EN_R2
www.lorexcctv.com
DEVICE CONNECTIONS (Stand Removed)
2a
Screws
Lay the monitor facing down on a soft surface. Make sure
to protect the screen from sharp objects.
OPTIONAL - LOCATE MONITOR CONNECTIONS
STEP 1 - SET UP YOUR MONITOR FIRST
2
The system has an efficient back panel control that
provides a cable management solution.
By design the connectors are not easily accessible, in
order to secure the connections.
It is recommended to remove the stand for initial set-up
by simpy unscrewing four screws with a standard screw
driver.
OPTIONAL - REMOVE MONITOR STAND
The stand comes with a built in cable channel to easily organize
and conceal wiring. Connect the Power Cable, Cameras, Ethernet
Cable and any Alarm Devices to the System by running the cables
through the hole in the stand before connecting to the
Observation System.
NOTE: Your system can be mounted on a wall using a VESA
standard mounting bracket (not included).
DEVICE CONNECTIONS
Tilt the monitor (40˚) to allow for easier access to the
connectors.
TILT MONITOR
1
3
Efficient back
panel provides
a solution for
neat cable
management.

Page: 4
L19LD800 SERIES QSG_EN_R2
www.lorexcctv.com
Page: 4
STEP 1 - SET UP YOUR MONITOR FIRST
Your system includes 4 high resolution 6 PIN DIN cameras.
CONNECT CAMERAS TO THE MONITOR
Connect one end of the ethernet cable to one of the router’s (not
included) LAN PORTS and the other end to the Monitor’s Network Port
located at the bottom of the monitor. See picture below showing a
generic LAN/WAN connection.
CONNECT ETHERNET CABLE
4
Connect one end of the Power adaptor to the monitor, the other end
to an electrical outlet. This unit powers ON once it is plugged in to the
power outlet.
TIP: Once you are done with the connections, remember to screw the
stand back on.
CONNECT POWER CABLE
5
WAN (WIDE
AREA NETWORK)
LAN (LOCAL AREA NETWORK)
TO YOUR COMPUTER
TO YOUR MONITOR
BACK OF THE ROUTER SHOWN
6
CONTINUED
TIP: Test the cameras prior to selecting
a permanent mounting location by
temporarily connecting the Cameras
and Cables to your System.
* Connect cameras to extension cables
by aligning the arrows. Plug in cameras
and cables before mounting the cameras.
NOTE: The arrow mark on top of the flat side of
the camera and cable connectors should face
UP while inserting to the Monitor.
Connect the first camera to the CH1 input. Follow the same steps to
connect the additional cameras.
4a
You can connect 4 additional (BNC) Cameras using the BNC ports.
With the use of a Universal DIN to BNC Cable you can connect 4 additional 6
PIN DIN Cameras to your monitor.
Note: BNC cameras require separate power adaptors. The SG7610B Camera
Kit includes an individual Power Adaptor and an Universal DIN to BNC Cable.
UNIvERSAL DIN TO BNC CABLE
OPTIONAL

Page: 4
Page: 4Page: 5
L19LD800 SERIES QSG_EN_R2
www.lorexcctv.com
DATE / TIME SETUP
SETUP
FORMAT
DATE 2007/09/16
TIME 19:08:13
TIME ZONE (GMT-05:00) Eastern Time
DST OFF
DATE YYYY/MM/DD
TIME 24H
INTERVAL OFF
SERVER
TIME SYNC
SYNC
STEP 1 - SET UP YOUR MONITOR FIRST
CONTINUED
The unit will automatically begin loading when power is connected to
the system.
INITIAL LOADING SEQUENCE
c
b
7
a
Click the MENU button on the front panel of the Monitor (or the
Remote Controller) to enter the Main Menu. From the Main Menu
move to SYSTEM and press the ENTER button to go to the DATE/TIME
menu to activate menu options.
SET THE DATE & TIME
9
Congratulations! You have completed Step 1
successfully. You can now view, record and
playback images on your monitor.
Make sure that
the Date and Time
are set prior to
recording.
• MENU Button – Accesses the setup menu, and returns to previous
menu options.
• Navigation Controls - Move Up/Down/Left/Right.
• Enter Button - Press this button to select and change the values in a
menu option.
NOTE: After you see all four (4) camera images
on your monitor screen, remove the protective
film from camera(s) and monitor screen.
a. During the loading sequence, the System will perform a Hard Drive and
Firmware check and the screen will display the text message “SYSTEM
CHECK”.
b. Once the system checks are completed, the screen will display the text
message “INITIALIZING SYSTEM” before completing the loading process.
c. The unit will initially load to a split screen view, displaying all 8 cameras
(if available) and a system legend in a 3x3 Screen View.
MENU NAVIGATION CONTROLS
8
MENU NAVIGATION &
ENTER
NOTE: This may take up to 60
seconds. Please wait until the
system completes loading.

Page: 6
L19LD800 SERIES QSG_EN_R2
www.lorexcctv.com
Page: 6
SYSTEM INFORMATION
SYSTEM NAME MYSYSTEM
SYSTEM ID 01
S/W VERSION 1.1.0.8
VIDEO TYPE NTSC
DDNS NAME
NETWORK PORT 3000
WEB PORT 80
IP ADDRESS 192.168.0.104
MAC ADDRESS 01:23:45:67:89:AB
DISK CAPACITY 120GB / 320GB
DISK TEMPERA TURE 100F (GOOD )
STEP 2 - SET UP LOCAL VIEWING ON YOUR PC
*YOUR OBSERVATION SYSTEM MUST BE CONNECTED TO A ROUTER PRIOR TO POWERING IT ON.
RECORD THE IP AND MAC ADDRESSES IN THE SECTION BELOW
NOTE: The system will lease
networking information from
your Router. If you wish to set
your information manually,
then set the DHCP MODE to
MANUAL. Please consult your
Hardware Manual for further
Menu options.
IP ADDRESS: . . .
MAC ADDRESS:
(Required for DDNS registration)
RETRIEVE SYSTEM INFORMATION
To retrieve the System Information, press the ENTER button on the front
panel of the Monitor or the Remote Control.
1
Insert the Lorex Client 3.0 Software CD into your local computer’s CD ROM
drive and proceed with the installation.
INSTALL SOFTWARE
(on your local computer)
Computer - not included
THIS STEP RELATES TO REMOTE VIEWING OVER THE LAN (LOCAL AREA NETWORK) BY USING A
PC LOCATED ON THE SAME NETWORK AS THAT OF THE SYSTEM.
2

Page: 6
Page: 6Page: 7
L19LD800 SERIES QSG_EN_R2
www.lorexcctv.com
STEP 2 - SET UP LOCAL VIEWING ON YOUR PC
CONTINUED
Follow the installation screens to complete Lorex Client 3.0
Software installation.
LOREX CLIENT 3.0 SOFTWARE
3
RUN LOREX CLIENT 3.0 SOFTWARE
(on your local computer)
4
LorexClient LorexPlayer
Lorex Client and LorexPlayer icons will appear on your desktop.
Double-click the Lorex Client icon on your desktop to run the program.
The log-in window may appear before the main program window loads.
Enter your password to start the program.
NOTE: Initial password is blank
Click the Menu button and select the NEW item.
ADD A LOCAL SITE:
(on your local computer)
5
TIP: When you run LorexClient on Windows XP operating system, you
will see the Windows Security Alert. Please click unblock to run the
application.
Please refer to your Lorex Client 3.0 Software Manual for instructions
about using Lorex Backup Player and Storage Calculator.

Page: 8
L19LD800 SERIES QSG_EN_R2
www.lorexcctv.com
Page: 8
STEP 2 - SET UP LOCAL VIEWING ON YOUR PC
CONTINUED
Enter a name and site information for the remote site.
1. Enter a Name of the site (e.g. Office)
2. Enter the User ID (admin by default)
3. Enter the User Password (blank by default)
4. Enter the DVR/Monitor TCP/IP port (3000 by default)
5. Enter the IP Address recorded in Step 2-1
6. Click Add to add the remote site
7. Click EXIT
ENTER SETUP INFORMATION
(on your local computer)
6
LOCAL LIVE SCREEN
(on your local computer)
Highlight the site you set-up in Step 2-6. Click the Connect
button and select the Connect item to connect the remote
site.
CONNECTION
(on your local computer)
7
Congratulations! You have completed Step 2 successfully.
You can now view, playback images and remotely control
your system on your local computer over the Local Area
Network (LAN).
8
8
1
2
3
45
67
Ofce

Page: 8
Page: 8Page: 9
L19LD800 SERIES QSG_EN_R2
www.lorexcctv.com
STEP 3 - SET UP INTERNET REMOTE
MONITORING
PORT FORWARD YOUR ROUTER
1
Port forward your router first before proceeding with the set-up
(ports 80, 3000, 3001, 3002, 3003).
All routers are different. To port forward your router, please refer to
your router’s user manual.
A router configuration guide is available on your Lorex Client Software
CD and also on www.lorexcctv.com/support in the Consumer’s
Guide Section.
DDNS SET-UP
Open your web browser (Internet Explorer by default)
and enter
http://ddns.strategicvista.net
in the address bar.
CREATE ACCOUNT
From the http://ddns.strategicvista.net website, click the
CREATE ACCOUNT option.
3
Router - not included
2
http://ddns.strategicvista.net

Page: 10
L19LD800 SERIES QSG_EN_R2
www.lorexcctv.com
Page: 10
STEP 3 - SET UP INTERNET REMOTE
MONITORING CONTINUED
COMPLETE NEW ACCOUNT INFORMATION
4
1. FOR PRODUCT LICENSE select the L19LD800 Series option
from the drop down menu.
2. FOR PRODUCT CODE enter the Monitor’s MAC address
(recorded in step 2-1).
3. FOR URL REQUEST enter a unique URL name
(e.g. myurl). NOTE: URL name should not be more than
15 characters.
12
3
REGISTRATION EMAIL
An automated REGISTRATION CONFIRMATION EMAIL will
be sent to your email. Print and Save this confirmation. You
will need this information to access your System remotely.
5
Service Provider: dns1.strategicvista.net
Domain Name: myurl.strategicvista.net
User ID: tomsmith1
Password: (your password)
ENTER DDNS SET-UP ON YOUR MONITOR
Once the DDNS settings have been configured online,
the information must be entered on the System to
allow for remote connection via the Lorex Software (or
through Internet Explorer).
Access the Main Menu Setup screens by pressing the
MENU key on the front panel of your monitor (or Remote
control) and navigate to the NETWORK option and press
ENTER. On the NETWORK SETUP screen scroll down
and select DDNS. Press the ENTER button to access the
DDNS network settings.
6
ENABLE DDNS SETTINGS
On the DDNS SETUP menu, enable DDNS by setting
ON/OFF to ON.
7