• Seconds setting
Press button “A” in accordance with a time
signal. The seconds are reset to “00” and
start immediately.
When the seconds count any number from
“30” to “59” and button “A” is pressed, one
minute is added and the seconds are imme-
diately reset to “00”.
Notes:
1. When setting the hour digits, check that
AM/PM is properly set. Only “PM” mark
is displayed. For the AM setting, there is
no indication.
2. When the time function is displayed in the
24-hour indication, the alarm will also be
displayed in the 24-hour indication.
3. If the watch is left untouched in the TIME
SETTING display with the digits flashing,
it will automatically return to the TIME
mode in 1 to 2 minutes.
■HOW TO SET THE ANALOGUE TIME
•Before setting the analogue time, be sure
to set the digital time.
(Refer to “HOW TO SET THE DIGITAL
TIME”.)
1. Pull out the crown when the second hand
is at the 12 o’clock position. The second
hand will stop on the spot.
2. Turn the crown to set the hour and minute
hands to the desired time.
*When setting the minute hand, advance
it 4 to 5 minutes ahead of the time and
then turn it back to the exact minute.
3. Push the crown back in to the normal position
when the second digits count “00” in the
digital time display.
Hour hand Minute hand
Normal
position
Extended
position
Crown
Second hand
■HOW TO SET THE ALARM
C
BA
Hour Minutes
Alarm mark
“PM” mark is displayed in the
12-hour indication.
“AM” mark is not displayed.
Hourly time
signal mark
1. Press button “B” to show the ALARM mode.
2. Press button “C” to show the ALARM
SETTING display. The hour digits start
flashing.
3. Selection of the digits to be adjusted (flashing)
is made in the following order by pressing
button “C”. MinutesHour →ALARM
mode
↑
4. Press button “A” to set the flashing digits.
One digit is advanced with each press of
button “A”. The flashing digits move quickly
by keeping button “A” pressed.
→
5. After all the adjustments are completed,
press button “B” to return to the ALARM
mode.
Notes:
1. When setting the alarm in the 12-hour in-
dication, check that AM/PM is properly
set. Only “PM” mark is displayed. For
the AM setting, there is no indication.
2. When the time function is displayed in the
24-hour indication, the alarm will also be
displayed in the 24-hour indication.
3. If the watch is left untouched in the ALARM
SETTING display with the digits flashing,
it will automatically return to the ALARM
mode in 1 to 2 minutes.
Engagement/disengagement of the alarm
•With each press of button “A” in the ALARM
mode, the alarm is engaged and disengaged
alternately.
When the alarm is engaged, the alarm mark
appears. When it is disengaged, the mark
disappears.
•At the designated time, the alarm rings for
20 seconds.
To stop it manually, press any of the but-
tons.
Alarm test
•The alarm can be tested by keeping but-
tons “A” and “C” pressed at the same time
in the CALENDAR or TIME mode.
Turning on/off of the hourly time signal
•With each press of buttons “A” and “C” in
the CALENDAR or TIME mode, the hourly
time signal is turned on and off alternately.
When the hourly time signal is turned on,
the hourly time signal mark appears. When
it is turned off, the mark disappears.
■HOW TO USE THE STOPWATCH
C
BA
Press button “B” to show the STOPWATCH
mode.
* Before using the stopwatch, be sure to re-
set the digits to “00'00"oo”.
* When measuring a long period of time, press
button “B” to return the STOPWATCH mode
to the CALENDAR or TIME mode after the
stopwatch starts. This will prevent any pos-
sible malfunction.
Minutes Seconds 1/100 seconds
•The stopwatch can measure up to 59 min-
utes and 59 seconds 99 in 1/100 second
increments.
•After 59 minutes and 59 seconds 99, it will
start counting again from “00'00"oo” as many
times as necessary until it is stopped.
Stopwatch operation
Standard measurement
A
Start
A
Stop
C
Reset
Accumulated elapsed time measurement
**Restart and stop of the stopwatch can be
repeated by pressing button “A”.
A
Start
A
Stop
A
Restart
** A
Stop
C
Reset
PM
ALARM CHRONOGRAPH
PM
PM
