LOTOO PAW 5000 User manual

Power
This device will recharge automatically when connect to 220V power supply with
the power adapter. When the player is off, long press <power > to turn on the
device.
· Playing while charging：The externally connected power adapter can supply
power to the device while charging the Lithium battery. Therefore, you can choose to
play music when charging the Lithium battery, which has no influence on the
charging performance.
When powered off, long press “POWER” to turn on
the device.
When powered on, short press “POWER” to
activate or turn off the screen. When the screen is
turned off, you can only operate the “POWER”,
”Volume+”, and ”Volume-” button.
Advice: when you play music long time, please turn off the
screen to improve this player's endurance performance.
Notes: you need buy the power adapter separately.
1) The player is turned on and the screen is
lighted, long press “POWER”. And it will turn off.
2) The player is turned on and the screen is out,
firstly press “POWER” to activate the screen. Then
long press “POWER”, you can turn off the device.
Package content
The package includes following accessories (The quantity for each accessory is
one ). Please carefully verify when purchasing. If anything absent, please contact
with the device supplier timely.
Player 3.5mm headphone
Warranty card
Notes：lotoo official website supply electronic version of the User manual book and fast setup.
Please visit www.lotoo.cn and download.
Sport arm belt
USB cable (power cable) Quick guide
快速操作手册
Hi-Fi Music Player
Key functions
Line output /SPDIF Optical fiber output
Headphone output
Balance type headphone output(2.5mm)
damp（high/low）
Volume up
Volume down
Next/Fast forward
Previous/Fast reverse
Jogdial
Play/ OK
Gain（high/low）
Liquid crystal display
Music/Fn（long press）
Return/Setup（Long press）
ATE/PMEQ music effects
Power/lock Screen
(01)
(02)
(03)
(04)
(05)
(06)
(07)
(08)
(09)
(10)
(11)
(12)
(13)
(14)
(15)
(16)
2. Power off
3. Recharge
1. Power on
保修说明
产品合格证
Hi-Fi Music Player
Install the TF card
装入TF卡
1. Inserting the TF card（As shown in figure1）
2. Pull out the TF card（As shown in figure 2）
Figure 2
Figure 1
取出TF卡
(01)
(02)
(03)
(04)
(05)
(06)
(07)
(08)
(09)
(10)
(11)
(12)
(13)
(14)
(15)
(16)
Insert the TF card into the slot according to the shell logo direction, push to hear "beep"
sound and release. Then the TF Card is installed.
Gently push the TF card bottom to hear "Di" sound, then slowly let go. You can see TF
Card pops up about 3mm. then you can directly take the card.
Instruction:
1) The device will turn on normally when the TF card is inserted. The device if self hasn't memory
capacity.
2) Theoretically, the device can support TF card with 2T capacity maximum.
3) The device can support the TF card with FAT32 format. So we advise: When inserting the TF card,
please format it first before use.
4) When inserting or pulling out the TF card, please be gentle, otherwise it may cause damage to
the TF card.
5) You can place four TF cards into the moving arm belt's bracket . Please follow the direction of
identification.

FCC Statement:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try
to correct the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and
receiver.
-Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV
technician for help.
To assure continued compliance, any changes or

modifications not expressly approved by the party
Responsible for compliance could void the user’s
authority to operate this equipment.
(Example- use only shielded interface cables when
connecting to computer or peripheral devices).
This equipment complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference,
and
(2) This device must accept any interference
received, including interference that may cause
undesired operation.
Caution!
The manufacturer is not responsible for any radio or
TV interference caused by unauthorized
modifications to this equipment. Such modifications
could void the user authority to operate the
equipment.
MODIFICATION: Any changes or modifications
not expressly approved by the grantee of this device
could void the user’s authority to operate the device.