LOX ES10 User manual

ES10 / ES10M WATER RESISTANT DOOR STRIKE
INSTALLATION MANUAL
INTRODUCTION:
WIRING AND POWER INPUT REQUIREMENTS:
ES10M DSS DOOR STATUS
SWITCH WIRING
SELECT EITHER THE 12V OR 24V SELECTOR PLUG TO SUIT THE VOLTAGE BEING USED, OR THE PLUGS MAY BE CUT OFF AND
WIRED AS BELOW.
The ES10 series strikes are designed to be morticed into a door frame on a single swing door equipped with either a mortice lock or a cylindrical tongue
lock. Rated strength 1200 kg
ES10 - Unmonitored weather resistant ( IP56 ) Electric Door Strike
ES10M - Monitored non weather resistant Electric Door Strike
• The ES10 series are supplied with two voltage selection plugs for operation on either 12VDC or 24VDC.
• If space does not permit the use of the plug/s provided they may be cut o and wired as shown below.
• AC power may also be used by adding a bridge rectifier -- see below.
• Note that direct connection of AC power will damage the strike and is not covered by warranty.
• Power to the ES10 series is not polarized.
ALTERNATE WIRING USING AC 12 - 24 VOLTS WITH A
BRIDGE RECTIFIER
ALTERNATE WIRING WITHOUT VOLTAGE
SELECTION PLUGS
12VDC (0.20A)
Non Polarised
RED
BLUE
YELLOW
BLACK
BLUE
ORANGE N/C
COM
N/O
BLACK
24VDC (0.10A)
Non Polarised
RED
BLUE
YELLOW
BLACK
For AC operation a Jaycar ZR1304
Bridge Rectifier is recommended
AC from power source DC to strike
1mm clearance
KeeperDoor
Door latch
Door Frame
Front face of
strike keeper
When the door is closed, ensure that there
is no back pressure on the front of the strike keeper
Bridge Rectifier
PROBLEM POSSIBLE CAUSE SOLUTION
DOOR WILL NOT LOCK INCORRECT VOLTAGE SELECTION CHECK VOLTAGE PLUG BEING USED
WILL NOT WORK IN ONE ORIENTATION 24V RATHER THAN 12V SELECTED CHECK VOLTAGE PLUG OR WIRING
1OCTOBER 2020

DIMENSIONS AND MOUNTING OPTIONS
2OCTOBER 2020
ES10 / ES10M WATER RESISTANT DOOR STRIKE
INSTALLATION MANUAL
METAL DOOR FRAMETIMBER DOOR FRAME
CHANGING LOCK FUNCTION FROM FAIL SAFE TO FAIL SECURE
WARNING:
DO NOT ATTEMPT TO SWIVEL THE KEEPER WHILE CHANGING THE FUNCTION, THIS WILL DAMAGE THE
BARBELL MECHANISM.
Step 1: Remove the spring screw from the end part of the strike body.
Step 2: Remove the Barbell to reverse in position with long part inside and short part out.
Step 3: Replace the spring screw.
Step 1: Remove the spring screw from the end part of the strike body.
Step 2: Remove the Barbell to reverse in position with short part inside and long part out.
Step 3: Replace the spring screw.
PROCEDURES TO CONVERT FAIL SECURE (FIGURE 4A) TO FAIL SAFE (FIGURE 4B):
PROCEDURES TO CONVERT FAIL SAFE (FIGURE 4B) TO FAIL SECURE (FIGURE 4A):
ORDERING
Remove rubber plug
prior to assembly of
extension lips (2 places)
Front face of
strike keeper
Dimensions (mm)
Spring screw
Spring screw
Barbell
Barbell
Barbell
Barbell
Wire hole
Latch area
Depth of lip cutout
will vary due width
of door frame and
mounting technique
20.5
15mm, 25mm,
50mm, 75mm
extension lips are
available options
86
38
105.2
124.7
86
3
6.5
17
36
20.5
32.7
POWER TO OPEN
FIGURE 4A
POWER TO LOCK
FIGURE 4B
PART NUMBER PRODUCT DESCRIPTION
ES10 NON MONITORED HIGH SECURITY ELECTRIC STRIKE
ES10M MONITORED HIGH SECURITY ELECTRIC STRIKE
ES10-EL15 ES10 EXTENSION LIP 15MM
ES10-EL25 ES10 EXTENSION LIP 25MM
ES10-EL50 ES10 EXTENSION LIP 50MM
ES10-EL75 ES10 EXTENSION LIP 50MM