LP Morgan Galleria User manual

www.lpmorgan.com.au
LP Morgan Galleria manual
Installation Instructions For:
• Plana U
• Novares
• Rear Projection
• Plana AT

2 | LP Morgan Installation Instructions
LP Morgan Galleria Manual
Table of contents
To the owner 3
Unpacking 4-5
Assembly instructions 6
Attaching the screen material 7-10
Trimming the screen material 10
Installing the assembled screen 11
Mounting the screen 12
Screen care 13-14
Warranty information 15
Information in this document is subject to change without notice.
© Herma Technologies. All rights reserved.
This document is protected against unauthorised copying electronic or otherwise.
Trademarks used in this text: Herma, the Herma Logo, Galleria, LP Morgan and
LP Morgan logo are registered trademarks of Herma Technologies.
Other trademarks and trade names used in this document remain the property
of the relevant owners.
June 2011 Version 3.2

LP Morgan Installation Instructions | 3
LP Morgan Galleria Manual
To the owner
Congratulations on purchasing an Australian made LP Morgan CineTheatre
Galleria Projection Screen. This cinema quality screen uses the finest optical
and mechanical components to give you a truly cinematic experience.
Please take a moment to review this manual, as it will ensure you many years
of service from your new LP Morgan CineTheatre Galleria Projection Screen.
Required tools and parts
6 or more screws to
suit wall type.
(Screw heads must be
no higher than 4mm)
Spirit level and pencil
for marking
Electric drill with drill
and driver bits

4 | LP Morgan Installation Instructions
LP Morgan Galleria Manual
Unpacking the Galleria Frame Screen
(Plana U / Novares / Rear Projection)
Supplied parts
Please check that you have all the components before assembly.
The EzyGrip and EzyMount are packed inside the fabric roll.
Front Projection Screens 140” and larger contain extra components.
See page 10.
1 x EzyMount
1 x Fabric Cutter
4 x Frame Sections
1 x Plastic Drop Sheet
4 x Corner Brackets
1 x 4mm Hex Key
1 x Fabric Roll
EzyGrip Lengths

LP Morgan Installation Instructions | 5
LP Morgan Galleria Manual
Unpacking the Galleria Frame Screen
(Plana AT)
Supplied parts
Please check that you have all the components before assembly.
The EzyGrip and EzyMount are packed inside the fabric roll.
Screens 140” and larger contain extra components.
See page 10.
1 x EzyMount
1 x Fabric Cutter
4 x Frame Sections
1 x Plastic Drop Sheet
Insertion Tool
4 x Corner Brackets
1 x 4mm Hex Key
Clamping Strip (numbered)
1 x Fabric Roll
EzyGrip Lengths

6 | LP Morgan Installation Instructions
LP Morgan Galleria Manual
Assembling the screen
Insert the corner brackets into
the short frame pieces first.
Be sure to insert them into the
lower channel and that the
grub screws are accessible
through the slot.
The corner brackets must be
inserted into the lower channel
Assemble the frame face down on a flat surface on the plastic drop sheet
provided. Please read the instructions carefully to avoid mistakes.
Attach the long frame pieces
into one end of the short
frame piece.
Insert the second short end
piece into the long frame pieces.
Check that all corners are firmly fitted together before tightening the grub
screws with the supplied hex key.

LP Morgan Installation Instructions | 7
LP Morgan Galleria Manual
The material is held in the
frame with EzyGrip. The
EzyGrip sits in its special
channel to hold the tension in
the screen.
Insert EzyGrip in the order shown below. Start at the corner of the frame
and work along the edge. Cut to length if necessary. Following the diagram
below insert the EzyGrip into the first side then when installing on the
opposite side apply tension to the fabric with one hand while inserting
the EzyGrip with the other.
1 2
34
5
6 7
8
• Insert the EzyGrip in the order shown
• Avoid lifting up the fabric, as the
EzyGrip may pop out
Roll the screen material onto the back of the screen. There is a sticker
attached to show you which side is the viewing side.
Attaching the screen material
(Plana U / Novares / Rear Projection)
EzyGrip in the wrong channel
EzyGrip in the wrong way around
Correct insertion of EzyGrip

8 | LP Morgan Installation Instructions
LP Morgan Galleria Manual
The material is held in the
frame with EzyGrip. The
EzyGrip sits in its special
channel to hold the tension in
the screen.
Allow enough fabric to overlap the frame sides to ensure the fabric can be
tensioned by hand.
Roll the screen material onto the back of the screen. There is a sticker
attached to show you which side is the viewing side.
Attaching the screen material (Plana AT)
EzyGrip in the wrong channel
EzyGrip in the wrong way around
Correct insertion of EzyGrip

LP Morgan Installation Instructions | 9
LP Morgan Galleria Manual
Insert the first section of EzyGrip into the correct channel using your
fingers, or hand tool provided.
Cut EzyGrip to length if necessary. Screw a matching numbered piece
of Clamping Strip to secure each length of EzyGrip in place as you
progress.This will stop the EzyGrip pulling out as tension is applied to
the fabric surface.
Start at the first corner of the joined frame and work around the edge.
Following the diagram below, insert the EzyGrip along the first side.
You can insert the lengths of EzyGrip in either a clockwise or
anticlockwise direction.
Clamping Strips
Start here Work in clockwise or
anticlockwise direction
Stretch and apply
tension to fabric
at each corner to
reduce ripples
Stretch and apply
tension to fabric
at each corner to
reduce ripples
Stretch and apply
tension to fabric
at each corner to
reduce ripples
Apply tension to the
fabric with one hand
while inserting the
EzyGrip with the other.
Tek Screw
Clamping Strip
Handle of EzyGrip
Frame Screen
1 2 3
4
5
678
9
10

10 | LP Morgan Installation Instructions
LP Morgan Galleria Manual
If you have ripples or creases in the image area, don’t panic! You can easily
remove the EzyGrip, retension the surface and re-install the EzyGrip.
1. Remove the clamping strip.
2. To remove the EzyGrip push
the handle forward, then lift it
up to remove.
3. Fix the clamping strip.
For Plana AT:
Be sure you have the tension correct before trimming the screen material,
as it is best not to remove the EzyGrip after trimming. Trim the excess fabric
with the fabric cutter supplied.
Trimming the screen material
Excess Fabric
Cutter
Slide the cutter
along the frame
while holding the
material. Avoid
lifitng the fabric.
• Hold the fabric with one hand, while
sliding the cutter along the inside
edge of the frame.
• Avoid lifting up the fabric, as the
EzyGrip may pop out.

LP Morgan Installation Instructions | 11
LP Morgan Galleria Manual
Spirit Level
EzyMount
Mounting surface
with wall studs
leave at least
60mm above
the mounting
holes to the
ceiling edge
or other fixture
The top of the
screen material is
55mm below the
mounting holes.
Installing the EzyMount
Carefully measure the desired screen position. Always use a spirit level as the
ceiling or walls may not be level. Measure, drill and fasten the EzyMount to
the wall using at least three screws approriate to the wall type (not supplied).
Installing the assembled screen
For Front Projection Screens 140” and larger
(not applicable for rear pro fabric)
Screens 140” and over in size
include a cross brace. The tabs
are already attached to the
frame and the bolts are installed
on the brace. Using the Hex key
loosen the bolts, install the brace
in the middle of the screen then
re-tighten the bolts.
If your frame has an included cross brace then it is supplied with two
lengths of EzyMount. When mounting the EzyMount leave a 150mm space
in between the two lengths. This space is for the brace and for lateral screen
adjustment to align your picture.

12 | LP Morgan Installation Instructions
LP Morgan Galleria Manual
Slide the screen sideways along the EzyMount to line up with the image.
Make sure the projector is perpendicular to the screen.
Mounting the screens
15º 15º
Tilt the screen 15o to hook onto the EzyMount. When you have hooked the
screen onto the EzyMount then lower it against the wall.

LP Morgan Installation Instructions | 13
LP Morgan Galleria Manual
Cleaning your Galleria Screen Surface
(Plana U / Novares / Rear Projection)
• Never use solvents, chemicals or abrasive cleaners on the screen.
• Never use a scraper, razor blade or other sharp object to clean the screen.
• Use a soft cloth to remove any loose dirt or dust particles.
• Clean the screen with a mild detergent solution and a sponge or lint
free cloth. Dab lightly to remove any stubborn marks, then blot with a
damp sponge to absorb excess water. Dab off the detergent with clean
water and dry with a soft cloth or towel. Do not let the detergent dry on
the screen.
Cleaning your frame
• If your frame is powder-coated or anodised, use water with a mild detergent
or methylated spirits and a soft cloth to wash off any marks. Rinse and dry
with a clean cloth or towel. Take care not to wet the screen surface.
• If your frame features a flocked velour finish, use a lint brush to remove any
dust on the frame.
Screen care

14 | LP Morgan Installation Instructions
LP Morgan Galleria Manual
Cleaning your Plana AT surface
• Remove dust with vacuum cleaner or compressed air.
• Do not scrub. Do not use solvents or any abrasive substance which might
damage the coating of the fabric.
• For small stains removal, try rubbing the fabric very gently with a clean white
pencil eraser.
• Clean the screen with a mild detergent solution and a sponge or lint free
cloth. Dab lightly to remove any stubborn marks, then blot with a damp
sponge to absorb excess water. Dab off the detergent with clean water and
dry with a soft cloth or towel. Do not let the detergent dry on the screen.
Cleaning your frame
• If your frame is powder-coated or anodised, use water with a mild detergent
or methylated spirits and a soft cloth to wash off any marks.
• Rinse and dry with a clean cloth or towel. Take care not to wet the
screen surface.
• If your frame features a flocked velour finish, use a lint brush to remove any
dust on the frame.
Screen care

LP Morgan Installation Instructions | 15
LP Morgan Galleria Manual
Warranty information
Keep your original receipt for warranty.
Please fill out the online warranty form in order to qualify for the manufacturer’s warranty.
http://www.lpmorgan.com.au/owners.html
The warranty covers defects in workmanship and materials, provided this product
has been installed in a normal environment and maintained according to the written
instructions. Herma warrants the product against loss of usefulness, discolouration or
deterioration of optical quality within the warranty period as a result of manufacturing or
material defects. This warranty applies only within Australia.
Please return your goods to the place of purchase for all warranty claims.
Conditions
Any equipment replaced pursuant to the terms of this warranty shall be retained
by Herma.
All costs related to de-installation and re-installation of the product covered by this
warranty are not the responsibility of Herma Technologies. Herma will not be responsible
for any consequential damages during or following installation procedures.
Herma is not responsible for any freight costs relating to repair or replacement.
Equipment must be returned to Herma in suitable packing to prevent damage in
transit. Herma will not accept any responsibility for damage to the equipment caused
by inadequate or unsuitable packing, or for any damage howsoever caused whilst the
goods are in transit.
Herma Technologies shall not be liable for any injury, loss or damage, direct or
consequential, arising out of the use of, misuse of, or inability to use, the equipment.
This Warranty does not cover any product which has been subjected to misuse,
abuse, neglect, accidental or intentional damage, improper voltage or any alteration
which affects the reliability or performance of the equipment not attributable to faulty
manufacture, parts or labour and without limiting the generality of the foregoing.
This Warranty does not cover any product where usage, adaptation or installation
are not in accordance with our written installation and operating instructions.
Warranty Periods:
• Galleria Frame and Assembly Hardware: Two years from date of purchase.
• Screen Surface: One year from date of purchase.

Factory 4a, 6 Albert Street Preston Vic 3072
Phone: [phone] Fax: [phone]
Email: [email protected] www.lpmorgan.com.au
For more information on our range of products,
please visit www.lpmorgan.com.au, or contact
your local LP Morgan Retailer.
For more information on our range of products,
please visit www.lpmorgan.com.au, or contact
your local LP Morgan Retailer.
June 2011 Version 3.2