LP Morgan Rondo Opus User manual

www.lpmorgan.com.au
Installation Instructions For:
• PrecisionDrive
• StandardMotorised
• CloseContactEasyFit
• Infra-RedEasyFit
• CineTheatre
LP Morgan Rondo Opus Manual

2 | LP Morgan Installation Instructions
LP Morgan Rondo Opus Manual
Table of contents
To the owner 2
Rondo Precision Drive parts supplied 3
Rondo Standard Motorised parts supplied 4
Rondo CC EasyFit parts supplied 5
Rondo IR (Infra-Red) EasyFit parts supplied 5
Wall mounting the screen - for all screens 6
Ceiling mounting the screen - for all screens 7
Concealed mounting - pelmet mounted
reverse wound screen 8
Electrical installation - Standard Motorised screens 9
Height adjustment - Standard Motorised screens 10
Electrical installation - CC EasyFit screen 11
Electrical installation - IR EasyFit screen 12
Limit setting - CC & IR EasyFit screens 13
Troubleshooting 14
Using Your Screen - Precision Drive 15
Maintenance - for all screens 16
Extras and accessories 17
Warranty information 18
Information in this document is subject to change without notice.
© Herma Technologies. All rights reserved.
This document is protected against unauthorised copying electronic or otherwise.
Trademarks used in this text: Herma, the Herma Logo, Galleria, LP Morgan and
LP Morgan logo are registered trademarks of Herma Technologies.
Other trademarks and trade names used in this document remain the property
of the relevant owners.
March 2012 Version 9.2

LP Morgan Installation Instructions | 3
LP Morgan Rondo Opus Manual
To the owner
Congratulations on purchasing an Australian made LP Morgan Rondo.
This high quality, stylish roller screen will give you great enjoyment and
a truly cinematic experience.
Please read this instruction manual before installing or
operating the screen.
Safety first
• Ensure you have the correct voltages for your screen
• Wiring for Standard Motorised Screens (Wall Switch Version) must be
done by a qualified electrician
• Should foreign matter fall into the unit, unplug it and have it checked by a
qualified technician before use
• Disconnect from the mains power using the plug . Don’t pull the cord!
• Work safely when installing the screen, use a ladder, be careful and wear
appropriate safety gear
• Please keep this book for future reference

4 | LP Morgan Installation Instructions
LP Morgan Rondo Opus Manual
The Chain is secured inside the casing for protection during transit.
Free the chain before installing. You may need to remove the front cover
to remove all tape.
The Dropper Bar is secured for transit.
Remove all adhesive tape before installing your screen.
Professional installation is recommended for this product.
3 x Ceiling BracketsChain wall mountScreen unit with chain
drive
3 x Wall Brackets
Rondo Precision Drive parts supplied

LP Morgan Installation Instructions | 5
LP Morgan Rondo Opus Manual
Rondo Standard Motorised parts supplied
3 x Ceiling BracketsScreen unit with Zwag
connector
3 x Wall Brackets
4mm Allen Key Zwag connector
with tool
Wall Switch & Surround
The Dropper Bar is secured for transit.
Remove all adhesive tape before installing your screen.
All mains wiring must be done by a licensed electrician.
Professional installation is recommended for this product.

6 | LP Morgan Installation Instructions
LP Morgan Rondo Opus Manual
The Dropper Bar is secured for transit.
Remove all adhesive tape before installing your screen.
All mains wiring must be done by a licensed electrician.
Professional installation is recommended for this product.
Screw Terminal
connector
Limit Setting ToolScreen unit with mains
plug and RJ9 data
cable
3 x Wall Brackets
IR Remote control
SOMFY
Rondo CC EasyFit parts supplied
Rondo IR (Infra-Red) EasyFit parts supplied
Same parts as Rondo CC EasyFit, plus:
3 x Ceiling Brackets
IR Sensor unit

LP Morgan Installation Instructions | 7
LP Morgan Rondo Opus Manual
Wall mounting the screen - for all screens
The wall brackets must be fastened securely to the wall. For plaster walls
please secure the brackets to the studs. Space the brackets evenly and as
wide as posssible to within 100mm from the end of the casing. This allows for
wiring (if needed) and also to give some lateral movement for projector and
screen alignment.
Screen
Measure and mark
carefully before fitting
Bracket
Stud Plasterboard
Place brackets as wide as possible to within
100mm of end of screen casing.
If you are fitting the screen in front of a window or other wall
fixture you may need to use a spacer (not provided) for the
dropper bar to fall freely (see right).
We recommend professional installation for all screens.
Spacer

8 | LP Morgan Installation Instructions
LP Morgan Rondo Opus Manual
After you have fitted the brackets simply hook the screen over
the top and snap into place.
Hook
Snap Installed
Ceiling mounting the screen - for all screens
The ceiling brackets must be attached to a joist, beam or other similar load
bearing device to safely carry the weight of your screen. Space the brackets
as wide as possible to within 100mm from each end of the screen (see wall
mounting picture).This allows lateral adjustment to align the projector image.
Ceiling
bracket
Roof
beam
Plaster
board

LP Morgan Installation Instructions | 9
LP Morgan Rondo Opus Manual
Installation in an LP Morgan HideAway
The LP Morgan HideAway stores your screen inside a cavity in the roof.
see www.lpmorgan.com.au for more details. Professional installation is
recommended for this product.
Ceiling
Ceiling trim Trapdoor panel
If you have ordered a special reverse wound screen, please follow the
instructions below. The surface is reverse wound on the roller, for
pelmet mounting.
Front of roll screen
If you have ordered a front of roll screen (not shown), the surface exits from
the front of the roller, which sets the bottom bar 60mm out from the wall.
The casing cover is supplied but should be removed immediately following
installation and before use.
Projector
Pelmet Reverse wound
screen
Concealed mounting - pelmet mounted reverse wound screen
Projector
Screen

10 | LP Morgan Installation Instructions
LP Morgan Rondo Opus Manual
Electrical installation - Standard Motorised screens
By law all mains wiring must be done by a qualified electrician.
Please show these instruction to your electrician.
The following diagram shows the Zwag connector and switch wiring for the
Rondo Standard Motorised. The lever arm tool is used to fix the wires into the
Zwag connector.
LP Morgan has a full range of other control options for use with your
Standard Motorised Screen; see page 17 for details.
See www.lpmorgan.com.au for more details.
Black (Down)
Blue (Common)
Brown (Up)
Green (Earth)
Brown (Active)
Green (Earth)
Blue (Neutral)
Screen
Wall switch
Zwag
Connectors
Blue
Black
Brown
Green
Lever arm tool
Mains