LUCCI Air ESPERANCE Series User manual

V1.0-AU (08/2021)
LUCCI
ESPERANCE SERIES
DC CEILING FAN WITH LIGHT
INSTALLATION
OPERATION
MAINTENANCE
WARRANTY INFORMATION
CAUTION
READ INSTRUCTIONS CAREFULLY FOR SAFE
INSTALLATION AND FAN OPERATION.

Airfusion Esperance Installation Instructions
1 | P a g e
THANK YOU FOR PURCHASING
Thank you for purchasing the latest in energy-saving ceiling fans. This fan runs on DC (direct current) power
which gives it the benefit of being super energy efficient while still maintaining high volume air-movement and
silent operation.
Energy-saving - The DC motor is the latest technology in fan design. Its highly efficient motor saves up to
65% more energy than ceiling fans with traditional AC motors.
Silent operation – This DC fan motor is programmed with a stabilised current which efficiently reduces motor
noise.
Low operating temperature – The DC power is managed effectively which brings down the motor operating
temperature to less than 50℃. This results in a much cooler motor than a standard AC fan and increases the
longevity of the motor.
6-speed remote control - Regular AC ceiling fans usually come with only 3 speeds, and this DC fan comes
complete with a 6 speed remote, which gives a greater choice of comfort levels.
SAFETY PRECAUTIONS
1. The appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning the use of the appliance by a person responsible for their safety.
2. Children should be supervised to ensure that they do not play with the appliance.
3. An all-pole disconnection switch must be incorporated into the fixed wiring, in accordance with local wiring
rules.
IN AUSTRALIA
WARNING:
FOR SAFE USE OF THIS FAN AN ALL-POLE DISCONNECTION
MUST BE INCORPORATED INTO THE FIXED WIRING IN
ACCORDANCE WITH THE WIRING RULES.
As outline in clause 7.12.2 of AS/NZS 60335-1 for meeting the minimum
electrical safety of this standard.
Please note warranty will be void if the installation is without a means for
an all-pole disconnection incorporated in the fixed wiring in accordance

Airfusion Esperance Installation Instructions
2 | P a g e
with the wiring rules.
Example: If a fan is connected to a circuit that can be isolated via an all-
pole safety switch at the switchboard, then this is considered to be an
all-pole disconnection to the ceiling fan electrical circuit, meeting the
requirements of clause 7.12.2 of AS/NZS 60335.1.
A single-pole switch on the active of the receiver input of remote
control must also be included in the wiring, and located the same
room as the ceiling fan.
4. Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities.
Contact your local government for information regarding the collection systems available. If electrical
appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater
and get into the food chain, damaging your health and well-being.
5. The structure to which the fan is to be mounted must be capable of supporting four time of the weight of
the fan.
6. The fan should be mounted so that the blades are at least 2.1 m above the floor.
7. This fan is suitable for indoor and alfresco areas where the fan is fully undercover with a minimum of 2
walls. This fan is not waterproof. When installed in an alfresco area, the ceiling fan must be positioned in
a location protected from water, wind, dust and salt. Exposure to these elements will void the warranty.
Mounting the fan in a situation where it is subject to water or moisture is dangerous and may increase the
risk of damage, injury or electrical shock.
8. Must be assembled and installed by a licensed electrician.
9. WARNING: If unusual wobbling or oscillating movement is observed, immediately stop using the ceiling
fan and contact the manufacturer, its service agent or suitably qualified persons.
10. The replacement of parts of the safety suspension system device shall be performed by the manufacturer,
its service agent or suitably qualified persons.
11. The fixing means for attachment to the ceiling such as hooks or other devices shall be fixed with sufficient
strength to withstand 4 times the weight of the ceiling fan; that the mounting of the suspension system
shall be performed by the manufacturer, its service agent or suitably qualified persons.
12. The light source contained in this luminaire shall only be replaced by the manufacturer or his service
agent of similar qualified agent.
NOTE: Do not attempt to remove the plastic protective cover of the LED module during any
circumstances. The LED PCB marked with can cause electrical shock

Airfusion Esperance Installation Instructions
3 | P a g e
PARTS LIST
• Unpack your ceiling fan carefully. Remove all parts and hardware.
• Lay out all the components on a smooth surface and make sure no components are missing before
assembling. If parts are missing, return the complete product to the place of purchase for inspection or
replacement.
• Check whether the ceiling fan has been damaged during transport. Do not operate/install any product
which appears damaged in any way. Return the complete product to the place of purchase for inspection,
repair or replacement.
• Examine all parts, and you should have the following:
Fig. 1

Airfusion Esperance Installation Instructions
4 | P a g e
INSTALLING THE FAN
TOOLS REQUIRED:
- Phillips / flat head screwdriver
- Pair of pliers
- Adjustable spanner
- Step ladder
- Wirecutter
- Wiring, supply cable as required by local provincial and national wiring codes and regulations
INSTALLING THE MOUNTING BRACKET
•The ceiling fan must be installed in a location so that the blades are spaced 300mm from the tip of the
blade to the nearest objects or walls.
•Install the hanging bracket to the ceiling joist or structure that is capable of carrying a load of at least four
times of the weight of fan, with two long screws provided. Ensure at least 30mm of the screw is threaded
into the support. (Fig. 2)
NOTE: The bracket screws provided are for use with wooden structures only. For structures other
than wood, the appropriate type of screw MUST be used. Ensure the screws used are suitable for the
mounting surface and the surrounding environment.
ANGLED CEILING INSTALLATION
The hanging system of this fan supports a maximum 28 degree angled ceiling installation.
Fig. 2
four times of the weight of the fan
Fig. 3

Airfusion Esperance Installation Instructions
5 | P a g e
INSTALLATION OF BLADE (Fig.4)
1. Unscrew the three screws from the cover of the fan blade and lift up blade cover; (Fig.4.1)
2. Install the fan blades onto the motor assembly; (Fig.4.2)
3. Install the cover back to the motor assembly by tightening the 3 screws. (Fig.4.3)
Fig. 4.1
Fig. 4.2

Airfusion Esperance Installation Instructions
6 | P a g e
Fig. 4.3

Airfusion Esperance Installation Instructions
7 | P a g e
HANGING OF THE FAN (Fig.5)
1. Place the hanger onto the mounting bracket. Ensure the key slot of the hanger ball is positioned on the
key pin of the mounting bracket to prevent the fan from rotating when in operation; (Fig.5.1)
2. Connect the wiring (Fig.5.2 & Refer to the wiring diagram in Fig.6 for more information)
- Connect the supply cable from the terminal block to the input of the drive component.
- Connect the quick connector.
- Check and ensure all wiring connections are secured.
3. Push the canopy up to cover the hanger and wiring parts (Fig.5.3)
4. Fix the canopy by tightening the two screws. (Fig.5.4)
Fig. 5
Fig. 5.3 Fig. 5.4
Fig. 5.1 Fig. 5.2

Airfusion Esperance Installation Instructions
8 | P a g e
WIRING DIAGRAM (FIG. 6)
WARNING: FOR YOUR SAFETY ALL ELECTRICAL CONNECTIONS MUST BE UNDERTAKEN BY A
LICENSED ELECTRICIAN.
NOTE: AN ADDITIONAL ALL POLE DISCONNECTION SWITCH MUST BE INCLUDED IN THE FIXED
WIRING.
NOTE: IF THERE ARE TWO OR MORE DC CEILING FANS INSTALLED IN THE ONE LOCATION, AN
ISOLATION SWITCH IS REQUIRED FOR EACH CEILING FAN. THIS IS REQUIRED WHEN
PROGRAMMING THE REMOTE AND RECEIVER TO PAIR TOGETHER.
NOTE: The L1 terminal is for the model with light only.
Fig. 6

Airfusion Esperance Installation Instructions
9 | P a g e
USING YOUR CEILING FAN
Install the rotatory fan switch on the wall plate and connect the wiring according to the below.
(NOTE: Only the fan rotatory switch is included as an accessory. Wall plate and light switch is not
included. Light switch is only required for the model with light)
Fan Wall Control
Turn on the power and check the operation of the fan.
• OFF Position – Fan off
• III Position – High fan speed
• II Position – Medium fan speed
• I Position – Low fan speed
Fig.7