LUCCI Airfusion Airmover User manual

V1.0- EN– Published on 08. 2017
LUCCI
AIRFUSION AIRMOVER
CEILING FAN
 INSTALLATION
 OPERATION
 MAINTENANCE
 WARRANTY INFORMATION
CAUTION
READ INSTRUCTIONS CAREFULLY FOR SAFE
INSTALLATION AND FAN OPERATION.

Airfusion Airmover Installation Instructions
2 | P a g e
THANK YOU FOR PURCHASING
Thank you for purchasing this quality Lucci product. To ensure correct function and safety, please read
and save all instructions before using the product.
SAFETY PRECAUTIONS
1. In Europe: This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning the use of the appliance in a safe way and
understand the hazards involved. Cleaning and maintenance shall not be undertaken by children
without supervision.
2. In Australia: The appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have
been given supervision or instruction concerning the use of the appliance by a person responsible
for their safety.
3. Children should be supervised to ensure that they do not play with the appliance.
4. An all-pole disconnection switch must be incorporated into the fixed wiring, in accordance with local
wiring rules.
IN AUSTRALIA
WARNING:
FOR SAFE USE OF THIS FAN AN ALL-POLE DISCONNECTION
MUST BE INCORPORATED INTO THE FIXED WIRING IN
ACCORDANCE WITH THE WIRING RULES.
As outline in clause 7.12.2 of AS/NZS 60335-1 for meeting the
minimum electrical safety of this standard.
Please note warranty will be void if installation is without a means for
an all-pole disconnection incorporated in the fixed wiring in
accordance with the wiring rules.

Airfusion Airmover Installation Instructions
3 | P a g e
Example: If a fan is connected to a circuit that can be isolated via an
all-pole safety switch at the switchboard, then this is considered to be
an all-pole disconnection to the ceiling fan electrical circuit, meeting
the requirements of clause 7.12.2 of AS/NZS 60335.1.
A single-pole switch on the active of the receiver input of remote
control must also be included in the wiring, and located the same
room as the ceiling fan.
5. Do not dispose of electrical appliances as unsorted municipal waste, use separate collection
facilities. Contact your local government for information regarding the collection systems available. If
electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the
ground water and get into the food chain, damaging your health and well-being.
6. The structure to which the fan is to be mounted must be capable of supporting a weight of 30kg.
7. The fan should be mounted so that the blades are at least 2.3m above the floor in Europe or 2.1m
above the floor in Australia.
8. This fan is suitable for indoor and alfresco areas where the fan is fully undercover with a minimum of
2 walls. This fan is not waterproof. When installed in an alfresco area, the ceiling fan must be
positioned in a location protected from water, wind, dust and salt. Exposure to these elements will
void the warranty. Mounting the fan in a situation where it is subject to water or moisture is
dangerous.
9. Only a licensed electrician should execute the installation.

Airfusion Airmover Installation Instructions
4 | P a g e
BEFORE INSTALLATION
Unpack the fan and carefully identify the parts. Please refer to Fig 1.
1 Mounting bracket x 1 8 Bottom cover x 1
2 Canopy x 1 9 Blade x 5
3 Down rod with ball joint x 1 10 Wooden screw x 2
4 Coupling cover x 1 11 Extra Motor screw x 1
5 Bolt x 1 12 Flat washer x 1
6 Pin x 1 13 Balance kit x 1 set
7 Motor assembly x 1 14 Wall switch with mounting screws x 1 set
Fig. 1

Airfusion Airmover Installation Instructions
5 | P a g e
INSTALLING THE MOUNTING BRACKET
 The ceiling fan must be installed in a location so that the blades are a minimum 300mm spacing
from the tip of the blade to the nearest objects or walls.
 Secure the hanging bracket to the ceiling joist or structure that is capable of carrying a load of at
least 30kg, with the two long screws provided. Ensure at least 30mm of the screw is threaded into
the support.
NOTE: The bracket screws provided are for use with wooden structures only. For structures
other than wood, the appropriate screw type MUST be used.
Angled Ceiling Installation
This fan hanging system supports a maximum 15 degree angled
ceiling installation.
Fig. 2
Fig. 3

Airfusion Airmover Installation Instructions
6 | P a g e
INSTALLING THE FAN
Installing the down rod
1) Feed the down rod (6) through the canopy (5) and the coupling cover (7).
2) Remove the ball joint (4) and cross pin (2) by loosening the set screw (3), insert the motor wires
(1) through the down rod then secure the ball joint and cross pin back to the down rod.
3) Insert the down rod to the coupling (8), line up the coupling holes with the down rod holes and
insert the bolt (10). Then insert the pin (11) to the end of the bolt.
4) Finally secure the down rod and coupling by tightening the two set screws (9) on the coupling.
HANGING THE FAN
Lift the fan assembly onto the mounting bracket. Ensure the registration slot (A) of the hanger ball is
positioned on the stopper (B) of the mounting bracket (C) to prevent the fan from rotating when in
operation. (Fig.5)
Fig. 5
Fig. 4

Airfusion Airmover Installation Instructions
7 | P a g e
BLADE INSTALLATION
BLADE ATTACHMENT (Fig.6)
 Align the two holes of the blade (3) to the fan
motor assembly (1).
 Secure the blade with two blade screws (4) and
flat washers (2) provided.
 Follow the same process for the remaining four
blades.
ELECTRICAL WIRING DIAGRAM
WARNING: FOR YOUR SAFETY ALL ELECTRICAL CONNECTIONS MUST BE UNDERTAKEN BY A
LICENSED ELECTRICIAN.
NOTE: AN ADDITIONAL ALL POLE DISCONNECTION SWITCH MUST BE INCLUDED IN THE FIXED
WIRING.
NOTE: Wiring diagram includes the light kit wiring. The light wiring diagram and switch is
omitted when no light kit is used with the ceiling fan.
USE WITH WALL SWITCH WIRING DIAGRAM:
Fig. 6
Fig. 7

Airfusion Airmover Installation Instructions
8 | P a g e
USE WITH REMOTE WIRING DIAGRAM: (REMOTE sold separately)
1/ Remote without plugs
2/ Remote with plugs
Fig. 8
Fig. 9

Airfusion Airmover Installation Instructions
9 | P a g e
FINISHING THE INSTALLATION
 After completing the electrical connection at the mounting bracket terminal block, connect the ceiling
fan wiring via the quick connector plug.
 Cover the mounting bracket with the canopy. Ensure all electrical wiring is tucked inside the canopy
and that the wires are not damaged during this step. Secure the canopy to the hanger bracket using
the screws provided.
USING YOUR CEILING FAN
FAN WALL CONTROL
Turn on the power and check the operation of the fan.
• OFF Position – Fan off
• 3rd Position – Low fan speed
• 2nd Position – Medium fan speed
• 1st Position – High fan speed
Light Control
• Toggle Switch – On/off
REVERSE FUNCTION
Your ceiling fan can operate either in fan mode or reverse fan mode.
SUMMER Mode: The reverse switch should be in the “down” (SUMMER) position to rotate the fan in an
anticlockwise direction. The airflow will be directed downwards, for cooling in summer.
WINTER Mode: The reverse switch should be in the “up” (WINTER) position to rotate the fan in a
clockwise direction. The airflow will be directed upwards assisting in the circulation of warm air, for
energy conservation in winter.
Fig. 11
Fig. 10

Airfusion Airmover Installation Instructions
10 | P a g e
The reverse switch is located in the top of the motor housing. Slide the switch to the LEFT for summer
weather operation. Slide the switch to the RIGHT for winter weather operation.
AFTER INSTALLATION
WOBBLE:
NOTE: ceiling fans tend to move during operation due to the fact that they are mounted on a rubber
grommet. If the fan was mounted rigidly to the ceiling it would cause excessive vibration. Movement of a
few centimetres is quite acceptable and DOES NOT suggest any problem.
TO REDUCE THE FAN WOBBLE: Please check that all screws which fix the mounting bracket and
down rod are secure.
NOTE: This fan has been precision balanced at the factory and will not need to be balanced again.
NOISE:
When it is quiet (especially at night) you may hear occasional small noises. Slight power fluctuations and
frequency signals superimposed in the electricity for off-peak hot water control, may cause a change in
fan motor noise. This is normal. Please allow a 24-hour “breaking-in” period, most noises associated
with a new fan disappear during this time. Please note that this is not a product fault and as such is not
covered under warranty – All electric motors are audible to some extent.
CARE AND CLEANING:
 Periodic cleaning of your ceiling fan is the only maintenance required. Use a soft brush or lint free
cloth to avoid scratching the paint finish. Please turn power off when you do so.
 Do not use water when cleaning your ceiling fan. It could damage the motor or the blades and create
the possibility of an electrical shock.
 The motor has a permanently lubricated ball bearing so there is no need to oil
NOTE: Always turn off the power at the mains switch before attempting to clean your fan.
Fig. 12