LUCCI THERMALITE 3 IN 1 Service manual

Installation Instructions
1 | P a g e
THERMALITE 3 IN 1 BATHROOM EXHAUST FAN
SKU# 200026, 200027, 200030, 200031, 200032, 200033
Rated Voltage 220-240V~ 50Hz
Thank you for purchasing this quality Lucci product. To ensure correct function and safety, please read and follow
all instructions carefully before using the product. Please keep instructions for future reference.
Warranty
•This light fitting is covered by a 3 year warranty. Please retain proof of purchase and evidence of installation by
a licensed electrician.
•Warranty will be void if there is any damage due to improper usage or modification to the fitting.
•Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void
warranty.
Installation requirements
•Must be installed by a licensed electrician.
•All wiring and installation of the light fitting must adhere to local and national wiring rules.
eg. AS/NZS 3000:2007/Amendment 2:2012 Electrical installations.
•Do not exceed the maximum wattage rating.
•Select a suitable location for installation;
- This product is rated IP24.
- The fitting can be installed in damp areas.
- The mounting point must support 2 times the weight of the fitting.
- The unit can be installed in flat ceilings with a minimum height of 2 metres. At least 220mm height
clearance in the ceiling cavity is required to ensure sufficient ventilation for moisture to disperse. The unit
must also be installed at least 400mm away from the walls.
- Ensure adequate inlets exist through windows, vents or under the door for air flow.
•Lay out all the components on a smooth surface and make sure there are no components missing before
assembling. If parts are missing, return the complete product to the place of purchase for inspection or
replacement.
•Check whether the fitting has been damaged during transport. Do not operate/install any product which
appears damaged in any way. Return the complete product to the place of purchase for inspection, repair or
replacement.
•Ensure power to the circuit you are working on has been switched OFF.
Installation directions
1. Remove the heat globes and illumination globe from the lampholder.
2. Remove the fascia from the body of the heater by loosening the spring hooks from the holes of the fascia.
3. The unit may be mounted either between joists using the in-built clip fasteners or against a joist using a screw
through the flange plate. Use this card in its open state as a template. Place in the required location and mark
out the hole cutting size. Please refer to the specification for the cut out size. Figure. 1
4. Before commencing cutting ensure that the area behind the intended location is clear of all cables, pipes and
joists. Once clear, cut out the section along the previously marked lines. Figure. 2
5. Install the duct cover on the wall; ensuring the blind shutters are facing down.
6. Install the vent duct to the exhaust hole on the fan body and fix it by a tie cable.
7. Install the other end of the vent duct to the duct cover and fix it using a tie cable.

Installation Instructions
2 | P a g e
8. Insert the unit into the square hole ensuring to pull the side springs inward so that the body can pass through
the hole without damaging the plaster. Ensure that the unit is held securely in place by the clips. If required,
additional screws can be used to aid holding the unit in the ceiling. Screw holes are provided in the flange for
this purpose. Figure. 3
9. Hold the Fascia against the body of the heater and the ceiling and attach the securing spring clips to hold the
fascia in place. Figure. 4
10. Install the heat lamps into the lampholder through the holes provided in the fascia. The globes should be
screwed up firmly to ensure a good electrical contact but ensure they are not over tightened. Next fit the small
centre globe in the same way ensuring that it is positioned centrally. Figure. 5
Wiring
•Remove the terminal cover on the fan body by loosening the screws and wire according to the label adjacent
to the terminal block. Make sure all cables are securely connected and reinstall the terminal cover.
•Connect the wiring to the switches as shown in the below electrical diagram.
•Install the plate of wall switch on the wall.

Installation Instructions
3 | P a g e
Safety tips
•Always ensure the power is OFF and the lamp has cooled down before performing any maintenance, cleaning,
changing the globe or adjustment to the fan.
•Do not touch the globe with bare hands. Use a clean cloth, gloves or a tissue.
•Ensure that the fitting does not come in contact with corrosive chemicals, etc.
•To clean, wipe with a damp clean cloth. Never soak the fitting with water.
Specifications
SKU #
200026
200027
200030
200031
200032
200033
Model #
LSA307
LSA03A
Rated Voltage
220-240V~ 50Hz
Fan Rated
Wattage
30 W
Heat Globe
Wattage
2 x 275W , ES,
R125 ,Reflector type
4 x 275W , ES, R125 , Reflector type
Light Globe
Wattage
1 x 42W , ES, R63, Halogen
1 x 70W , ES, R80, Halogen
Cutout Size
345 x 190 mm
290 x 290 mm
Fan Exhaust
Hole
100mm
IP Rating
IP24
Dimensions
H223 x W250mm x L430mm
H217 x W373mm x L373mm
H217 x W375mm x L448mm
Weight
??kg
??kg
??kg

Installation Instructions
4 | P a g e
BATHROOM HEATER WARRANTY CARD
Every Lucci Thermalite 3 in 1 is thoroughly inspected and tested before being released for sale. In addition to any warranties or conditions
implied by applicable Statue or Regulation, Lucci Design warrants all of it’s bathroom heaters against defective workmanship and faulty
materials for thirty six (36) months from the original date of purchase. Lucci Design undertakes, at it’s option, to repair or replace, free of
charge, each product or part thereof subject to the below warranty conditions;
1) The fan or relevant part has not been modified, subjected to misuse, neglect, or been involved in an accident.
2) The repairs are not required as a result of normal wear and tear.
3) The product was installed by a licenced electrical contractor in accordance with this instruction manual.
4) No solid state speed control device has been used with the appliance.
5) A copy of the original receipt of purchase is presented.
6) Globes supplied are not covered by this warranty
Lucci Design cannot be held responsible for any repair other than those carried out by it or one of it’s Authorised Service Agents.
Please keep this warranty form in a safe place. This form must be produced in the event of service being required.
IN THE EVENT OF SERVICE BEING REQUIRED, PLEASE CALL
THE LUCCI FAN WARRANTY HOTLINE ON 1800 602 243 BETWEEN
9AM & 5PM (E.S.T) MONDAY TO FRIDAY ENSURING THAT YOU
HAVE THE FOLLOWING DETAILS ON HAND:
MODEL (SKU) NUMBER: __________________________________________________________
DATE OF PURCHASE: ____________________________________________________________
RETAILER: _____________________________________________________________________
RECEIPT NUMBER: ______________________________________________________________
INSTALLED BY: _________________________________________________________________
LICENCE # : ______________________________ PH: __________________________________
DESCRIPTION OF FAULT: _________________________________________________________
______________________________________________________