Lumascape LS698-K Installation instructions manual

INC.
Lumascape USA Inc.
1300 Industrial Rd., Unit #19
San Carlos, CA 94070, USA
T 1-(650)-595-LUMA(5862)
F 1-(650)-595-5820
E [email protected]
W www.lumascape.com
IMPORTANT INSTRUCTIONS
For installation of:
pre-installation and drive over kit LS698-K
IMPORTANT
- This product must only be installed by a licensed electrical worker. P
- This fixture is suitable for wall, floor and in-grade mounting. Suitable for drive-over applications.
lease ensure that Installation
complies with local authority standards.
Certified LUXEON
Luminaire Manufacturer
C1741US - 2012_03_REV-004
LUMASCAPE USA INC
T 1-(650)-595-LUMA(5862) 1-(650)-595-5820
Free Call 1-866-695-LUMA(5862)
A.C.N. 010 572 773
LS553LED - Ix23-x / LS563LED - Ix23-x
Line voltage input 100-240V AC
IP68 rated, Class 1
Rx23-x Rx23-xLS553LED - / LS563LED
Remote LED driver 350mA constant current
IP68 rated, Class 3
MODELS
TO SUIT
LS698-K, LS698-K-CP
WARNING
DO NOT INTERFERE WITH OR DISCONNECT CABLE FROM FITTING. WARRANTY WILL BE VOID IF CABLE ASSEMBLY IS
4
POUR CONCRETE
Ensure top of brass collar is at the finished
floor level prior to pouring.
IMPORTANT NOTES:
Ensure that the collar is flush with the
finished floor level
Ensure inside faces of brass collar remain
clean from debris and concrete.
3
FIT CONDUIT AND PLACE
FIXTURE
Feed cable from fixture through conduit.
Screw conduit to outer housing and place
fixture into hole.
IMPORTANT NOTE:
Electrical conduit used as per NEC.
REMOVE FIXTURE FROM OUTER
HOUSING
Remove the two screws fom the lid of the
fixture. Carefully pry the fixture from the
brass collar and place in a safe location for
future installation
OUTER
HOUSING
FIXTURE
2
1
SPACE REQUIREMENTS
- Site fixtures ensuring the hole is as specified.
IMPORTANT NOTE:
Electrical conduit used as per NEC.
CONDUIT
HOLE MINIMUM
5.25”
(133mm)
11” (280mm) min
FINISHED
FLOOR LEVEL
ARMOURED CABLE
31” (790mm)
ARMOURED CABLE/SPLICE BOX
CONFIGURATION
FOR CONDUIT ENTRY
CONFIGURATION
ONLY

IMPORTANT NOTE FOR REMOTE
DRIVER MODEL, (LS5X3-X-DXXXX):
Connections are in series.
Ensure cable polarities are correct:
Brown or Red (+) positive
Black or Blue (-) negative
Main lines must be a minimum of 4mm if
supplied connection devices are used.
2
CONNECTIONS FOR REMOTE MODEL ONLY
++
++
++
__
__
__
Constant Current Supply
from Remote Driver
INC.
www.lumascape.com
LUMASCAPE USA INC
T 1-(650)-595-LUMA(5862) 1-(650)-595-5820
Free Call 1-866-695-LUMA(5862)
5
TERMINATE FIXTURE
Connect lead from the bottom of the fixture to the
cable inside the outer housing.
6
FIT FIXTURE INTO HOUSING
Check the brass collar and the o-ring on the fixture
are clean and free from debris. Note there is a film
of grease on the o-ring. If necessary replace with
tm
Molykote Valve and Oring Lubricant, or equivalent.
Source: Luxeon LED 1 Watt
Input: Remote LED driver 350mA constant current (see below for recommended drivers)
technical data - remote driver, 350mA input
Part Number Description Application
LS783 DRIVER LED 350mA 40W Remote supply for 4 to 6 fittings
LS784 DRIVER LED 550mA 20W Remote supply for 6 to 9 fittings
Remote LED Drivers
Source: Luxeon LED 1 Watt
Input: 100-240V AC, 50/60Hz
technical data - line voltage input
The correct power supply must be used in conjunction with the Luxeon LED light sources. This will ensure the maximum life of
the LED light source.
warning
SEALING
SURFACE
O-RING
A.C.N. 010 572 773
LS553LED-X-IXX23 / LS563LED-X-
IX23
Line voltage input 100-240V AC
LS553LED-X-RXX23 / LS563LED-X-RX23
Remote LED driver 350mA constant current
IP68 rated, Class 3
MODELS
TO SUIT
LS698-K, LS698-K-CP
C1741US - 2012_03_REV-004