Lumberjack TS210SL User manual

TS210SL
210mm Table Saw With Side Extensions
TS210SL
ORIGINAL INSTRUCTIONS
SAFETY AND OPERATING MANUAL

TS210SL
TABLE OF CONTENTS
Welcome to Lumberjack!
Dear customer, Congratulations on your purchase. Before using the
product for the first time please be sure to read these instructions for use.
They provide you with all information necessary for using the product safely and to
ensure its long service life.
Closely observe all safety information in these instructions!
General Power Tool Safety Warnings………………………………….…......01
Symbols & Cable Rating Chart ……….…………………………………….………06
Machine Details and Product Features……….…………………………….….07
Assembly……………………………………………………………………………………..09
Operation……………………………………….…………………………………………..13
Maintenance and Service……………………………..……………………………..15
Lumberjack Guarantee………….…………………………………………………….17
Declaration of Conformity……………………………………………………………19
Parts List…………..………………………………………………………………………...20
Parts Diagram………………………………………………………………………………23

TS210SL 01
GENERAL POWER TOOL SAFETY WARNINGS
WARNING Read all safety warnings and
all instructions. Failure to follow the warnings
and instructions may result in electric shock, fire
and/or serious injury.
Save all warnings and instructions for
future reference. The term "power tool" in
the warnings refers to your electric (corded)
power tool or battery-operated (cordless) power
tool.
1. Work area safety
a) Keep work area clean and well lit. Cluttered
or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or
fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
2. Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do not use
any adapter plugs with grounded power tools.
Unmodified plugs and matching outlets will
reduce risk of electric shock.
b) Avoid body contact with grounded surfaces,
such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of
electric shock.
f) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk
of electric shock.
3. Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power
tools may result in serious personal injury.
b) Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off position before connecting to
power source and/or battery pack, picking up or
carrying the tool. Carrying power tools with your
finger on the switch or energising power tools that
have the switch on invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.

TS210SL 02
GENERAL POWER TOOL SAFETY WARNINGS
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes,
jewellery or long hair can be caught in moving
parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
4. Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off. Any power tool that
cannot be controlled with the switch is
dangerous and must be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tool’s operation. If damaged, have the power tool
repaired before use. Many accidents are caused
by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions, taking
into account the working conditions and the work
to be performed. Use of the power tool for
operations different from those intended could
result in a hazardous situation.
5. Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
b) If the replacement of the supply cord is
necessary, this has to be done by the
manufacturer or its agent in order to avoid a
safety hazard.

TS210SL 03
GENERAL POWER TOOL SAFETY WARNINGS
6 . Additional Safety and Working
Instructions
a) Dusts from materials such as lead-containing
coatings, some wood types, minerals and
metals can be harmful to one’s health and
cause allergic reactions, leading to respiratory
infections and/or cancer. Materials containing
asbestos may only be worked by specialists.
Observe the relevant regulations in your country
for the materials to be worked.
b) Prevent dust accumulation at the workplace.
Dusts can easily ignite.
7. Safety Warnings for Dust Extractors
a) Do not vacuum materials that are harmful to
one’s health, e. g. dust from beech or oak
wood, masonry dust, asbestos. These materials
are considered carcinogenic.
b) Take care that the blade guard operates
properly and can move freely. Always adjust
the blade guard in such a manner that it face
loosely against the work piece when sawing.
Never clamp the blade guard when it is open.
c) Never reach behind the saw blade in order to
hold the work piece, remove saw dust/wood
chips or for any other reason. The clearance of
your hand to the rotating saw blade is too small.
d) Guide the work piece against the saw blade
only when the machine is switched on.
Otherwise there is damage of kickback, when
the saw blade becomes wedged in the work
piece.
e) Keep handles dry, clean, and free from oil
and grease. Greasy, oily handles are slippery
causing loss of control.
f) Operate the power tool only when the work
area to the work piece is clear of any adjusting
tools, wood chips, etc. Small pieces of wood or
other objects that come in contact with the
rotating saw blade can strike the operator with
high speed.
g) Only saw one work piece at a time. Work
pieces placed on top or aside of each other can
cause the saw blade to jam or the work pieces to
move against each other while sawing.
h) Always use the parallel guide or the angle
guide. This improves the cutting accuracy and
reduces the possibility of saw blade binding.
i) Use the machine for grooving or rebating only
with an appropriately suitable protective device
(e. g. a tunnel blade guard).
j) Do not use the machine for cutting slots
(stopped grooves).
k) Use the machine only for cutting the materials
listed under Intended Use. Otherwise, the
machine can be subject to overload.
l) If the saw blade should become jammed,
switch the machine off and hold the work piece
until the saw blade comes to a complete stop. To
prevent kick back, the work piece may not be
moved until after the machine has come to a
complete stop. Correct the cause for the jamming
of the saw blade before restarting the machine.
m) Do not use dull, cracked, bent or damaged
saw blades. Unsharpened or improperly set saw
blades produce narrow kerfs causing excessive
friction, blade binding and kickback.

TS210SL 04
GENERAL POWER TOOL SAFETY WARNINGS
n) Always use saw blade with correct size and
shape (diamond versus round) of arbour hole.
Saw blade that do not match the mounting
hardware of the saw will run eccentrically,
causing loss of control.
o) Do not use high speed steel (HSS) saw blade.
Such saw blades can easily break.
p) Do not touch the saw blade after working
before it has cooled. The saw blade becomes
very hot while working.
q) Never operate the machine without the
insert plate. Replace a defective insert plate.
Without flawless insert plates, injuries are
possible from the saw blade.
r) Check the cable regularly and have a
damaged cable repaired only through an
authorised customer service agent. Replace
damaged extension cables. This will ensure that
the safety of the power tool is maintained.
s) Store the machine in a safe manner when not
being used. The storage location must be dry
and lockable. This prevents the machine from
storage damage, and from being operated by
untrained persons.
t) Never leave the machine before it has come
to a complete stop. Cutting tools that are still
running can cause injuries.
u) Never use the machine with a damaged
cable. Do not touch the damaged cable and pull
the main plug when the cable is damaged while
working. Damaged cables increase the risk of an
electric shock.
8. Safety Warnings for Lasers
The mitre saw has a built-in laser light. The laser is
CLASS 2. These lasers do not normally present an
optical hazard. However, DO NOT stare at the
beam, as this can cause flash blindness.
a) Do not remove or deface any product labels.
Removing product labels increases the risk of
exposure to laser radiation.
b) The laser beam can be harmful to the eyes.
Always avoid direct expose to eyes. Do not project
the laser beam directly into the eyes or at any
object other than the work piece.
c) Do not look directly into the laser-beam-
output aperture during operation.
d) Turn the laser on only when making cuts. The
laser on the mitre saw is not a toy. Always keep it
out of the reach of children. The laser light
emitted from this device should never be directed
toward any person for any reason.
e) Always turn the laser beam off when it is not in
use. Leaving the tool will increase the risk of
someone inadvertently staring into the laser’s
beam.
f) Be sure that the laser beam is aimed at a work
piece (such as wood or a rough-coated surface)
that does not have a reflective surface.
g) Do not use on materials that have shiny,
reflective surfaces, such as sheet metal. The
reflective surface could reflect the beam back at
the operator. Be aware that laser light reflected
off of a mirror or any other reflective surfaces can
also be dangerous.

TS210SL 05
GENERAL POWER TOOL SAFETY WARNINGS
h) Always wear laser-protective eyewear when
working on or near reflective surfaces.
i) Do not attempt to activate the laser when the
tool housing is removed.
j) The laser is activated by means of a button
switch that is independent of the main switch
for the saw.
k) Do not replace the laser light assembly with a
different one. Any repairs must be carried out by
the laser manufacturer or an authorized service
agent.
l) Do not attempt to repair the laser guide by
yourself.
m) Do not attempt to change any parts of the
laser guide.

TS210SL 06
SYMBOLS AND POWER RATING CHART
Danger! –Read the operating
instructions to reduce the risk of
injury.
Caution! Wear safety goggles.
Caution! Wear ear defenders. The
impact of noise can cause
damage to hearing.
Caution! Risk of Injury! Do
not reach into the running
saw blade.
Caution! Wear a dust mask.
Class II Double Insulated

AIR6V 01
AIR6V 01
AIR6V 01
AIR6V 01
TS210SL 07
MACHINE DETAILS AND PRODUCT FEATURES
Machine Details
Specifications:
Mains Voltage - 230V / 50Hz
Power Consumption - 1500W;
No Load Speed - 5000rpm
Blade Spec - Ø210 x Ø30 x 2.8mm
Cutting Capacity:
At 90 degrees - 70mm
At 45 degrees - 45mm
Max Table Size - 465 x 500mm
Nett Weight - 11.5kg
Package Contents:
Machine body
Rip fence
Blade guard
Suction hose
Central struts long (2x)
Central struts short (2x)
Leg (4x)
Mitre gauge
Ring spanner
Saw blade key
Leg support (2x)
Rubber foot (4x)
Table extension (2x)
Push stick
Fasteners
Intended Use
The power tool is intended as a stationary
machine for making straight lengthways
and crossways cuts in wood.
The capacity of the power tool is designed
for sawing hardwood and softwood.
The power tool is not suitable for cutting
aluminium or other non-ferrous metals or
alloys.
Product Features
1. Saw table
2. Table insert
3. Saw blade
4. Blade guard
5. Suction hose
6. Riving knife
7. Mitre gauge
8. Table extension
9. Push stick
10. Under frame
11. On-Off switch
12. Reset button for motor
overload cut out
13. Blade height hand wheel
14. Blade tilt lock knob
15. Screw
16. Rip fence
17. Legs
17a.Rubber feet
17b.Leg support stay
18. Long cross brace
19. Short cross brace
20. Hexagon head screw
21. Hexagon nut
22a. Saw blade spanner
22b.Saw blade spanner
23. Support struts

z
AIR6V 01
AIR6V 01
AIR6V 01
AIR6V 01
TS210SL 08
MACHINE DETAILS AND PRODUCT FEATURES

TS210SL 09
ASSEMBLY INSTRUCTIONS
Assembly
Avoid unintentional starting of the machine.
During assembly and for all work on the
machine, the power plug must not be
connected to the mains supply.
Carefully remove all parts included in the
delivery from their packaging.
Remove all packaging material from the machine
and the accessories provided.
Before starting the operation of the machine for
the first time, check if all parts listed in the box
content section have been supplied
Note: Check the power tool for possible damage.
Before further use of the machine, check that all
protective devices are fully functional. Any
lightly damaged parts must be carefully checked
to ensure flawless operation of the tool. All parts
must be properly mounted and all conditions
fulfilled that ensure faultless operation.
Damaged protective devices and parts must be
immediately replaced by an authorised service
centre.
Dust extraction
Dust from materials such as lead-containing
paint, different kinds of wood, minerals and
metal maybe harmful to health. Touching of
inhaling the dust can cause allergic reactions
and/or ailments of the respiratory tract of the
user or persons in the vicinity. Certain dust such
as oak or beech dust is considered carcinogenic,
particularly in combination with wood treatment
additives (chromate, wood preservatives).
Materials containing asbestos may only be
processed by experts.
–Always use a dust extraction facility.
–Make sure the workplace is well ventilated.
–Always wear a dust protection mask.
–Observe the regulations valid in your country for
the materials to be processed.
Attach the Table Extensions
1. Make sure that the saw blade is at its lowest
setting. Turn the saw upside down and place it on
the floor with the table facing down.
2. Line the table extension (8) up with the edge of
the saw table (1).
3. Loosely fasten the extension to the table using
hexagon head screws (20) and nuts (21). Repeat
the procedure on the opposite side of the table.
4. Screw the support struts (23) to the table
extensions with washers and nuts.
5. Tighten the nuts when both extensions have
been attached.

TS210SL 10
ASSEMBLY INSTRUCTIONS
Attaching the Sub-Frame
1 .Attach the legs(17) as shown in the picture.
The ends of the support struts are fastened using
the screws (15) as the legs, as shown in the
picture.
2. Push the rubber feed (17a) onto the ends of
the legs.
3. Screw on the cross braces (18 and 19). The
long cross braces should be installed parallel to
the control/front side of the saw.
4. Screw on the leg support stays (17b) as shown
in the picture. They should be installed on the
rear legs.
Riving knife and saw blade
Riving knife
1. Remove the saw table insert by undoing the
screw (see picture) and lifting out the insert.
2. Set the saw blade to its maximum height
setting by turning the hand wheel (13)
clockwise.
3. Make sure that the tilt angle is set to 0° and
locked using the lock knob (14).
4. Place the riving knife over the alignment lugs.

TS210SL 11
ASSEMBLY INSTRUCTIONS
5. Secure the riving knife with the washer and
set screw making sure that the arrow on the
washer point s to the saw blade as shown in the
picture.
Saw blade
1. Make sure that the inner flange
washer(the inner washer has a round
hole in the centre) is placed on the drive
shaft.
2. Place the saw blade onto the flange of the
support washer. Make sure that the saw blade is
facing the right way. The direction of rotation
markings on the blade should be facing outwards
and correspond with the markings on the saw.
3. Fit the outer flange washer and screw in the
lock nut. Hold the drive shaft with one of the
spanners on the outer flange washer whilst
simultaneously tightening the lock nut (clockwise).
Changing the blade
Warning: Make sure that the saw is disconnected
from the power supply before starting to change
the saw blade. Wear safety gloves.
1. Remove the saw table insert by undoing the
screw (see picture) and lifting out the table insert.
2. Set the saw blade to its maximum height setting
by turning the hand wheel (13) clockwise.
3. Remove the old saw blade using the two
spanners. Then following the saw blade
installation instructions above, making sure to
adjust the riving knife if necessary (instructions
below).

TS210SL 12
ASSEMBLY INSTRUCTIONS
Adjusting the riving knife
Undo the set screw and adjust the knife so that it
follows the curvature of the saw blade with a
maximum distance from the blade of 5.mm.
Blade guard
Screw the blade guard onto the top of the riving
knife. Do not tighten the nut too tightly; the
blade guard must be able to move freely.
Dust extraction port adaptor
If a dust extractor is used, connect the suction
hose (5) between the blade guard and the dust
extraction port adaptor.

TS210SL 13
OPERATION
Operation
. Make sure that the saw is completely intact and
correctly assembled before commencing work.
. Check that the saw blade is vertical (90°) and is
not set higher than is necessary to just manage
to saw through the thickness of the work piece.
. Regularly check that all nuts and screws are
tight.
ON/OFF switch (start/stop)
Plug the mains lead into a wall socket.
Switching on: Push the green button [I] to start
the motor.
Switching off: Push the red button [0] to turn
the motor off.
No-volt release switch
The saw is equipped with a no-volt release
switch which prevents it from starting
automatically when the power comes back on
following a power cut. Once power has been
restored the saw must be switched on again by
pressing [l].
Motor overload cut-out
If the motor is overloaded due to incorrect work
piece feed or the saw blade being
Obstructed by debris, the overload cut-out may
be triggered.
If the overload safety cut-off switch is triggered:
Unplug the mains lead and let the saw cool
down for at least 10 minutes.
Make sure that no contaminants hinder the
rotation of the saw blade; brush off and vacuum
saw dust as and when required.
Press the overload cut-out reset button (a)
pictured.
Switch the saw on by pressing [I].
Setting the saw blade height
Turn the hand wheel (13) to set the desired height.
Never set the blade higher than is necessary to
saw through the work piece.
Rip fence
Place the rip fence onto the table-board and lock it
in place by lowering the locking lever ((b).in the
picture).

TS210SL 14
OPERATION
The rip fence can be attached in two ways, with
the high side or the low side facing the saw
blade (the low side makes it easier to handle thin
material such as plywood). Loosen the wing nuts
and remove the rip fence from the rail.
Position the rip fence in the desired position and
tighten the wing nuts.
Adjusting the Parallel
Pull the clamping lever (b) upwards.
Move the cross stop (16) into the required
position. Press the clamping lever (b) down.
Mitre gauge
Slide the mitre gauge into one of the slots on the
table.
Undo the locking knob (c) and set the desired
angle. Tighten the locking knob again.
If necessary, undo the two wing nuts (d) and
move the rip fence to the side so that it does not
catch on the blade, then tighten the wing nuts
again.

TS210SL 15
OPERATION AND MAINTENANCE AND SERVICE
Setting the blade tilt
Note: Check all the angles before starting to saw.
Undo the locking knob (14) and set the desired
angle.
Tighten the locking knob again.
Rip cutting
Note:
Rehearse every step of the cutting task without
turning the saw on if you are unsure how to hold
the work piece and work safely.
Make a test cut and measure before starting to
rip cut on the actual work piece.
Always let the saw come up to full speed before
starting to cut.
Be extra careful at the beginning of every cut.
When rip-cutting thick work pieces where the
saw blade is set to its maximum height: check
that the riving knife is set to its maximum height
setting otherwise there is a risk of the work
piece fastening on the blade guard. Refer to the
Adjusting the riving knife section.
Hold one side of the material against the rip
fence and the flat face against the surface of the
table.
Do not stand directly behind the work piece
when rip cutting. The work piece can be thrown
back towards the operator.
Place your hands on the work piece and press it
against the table and the rip fence. Feed the
work piece into the blade in a controlled and
smooth motion.
.
Warning: Always use a.push-stick if any of your
hands comes closer than 125.mm to the.saw
blade during the.cutting process. Never use
a.damaged push-stick, replace a.damaged stick
Maintenance and Service
Maintenance and Cleaning
Before any work on the machine itself,
pull the mains plug.
If the machine should fail despite the care taken in
manufacturing and testing procedures, repair
should be carried out by an approve service
centre.
–Store the tool, instruction manual and
accessories in a secure place. In this way you will
always have all the information and parts on hand.
Cleaning
–For safe and proper working, always keep the
power too land its ventilation slots clean.
–Remove dust and chips after each working
procedure by blowing out with compressed air or
with a brush.

AIR6V 01AIR6V 01AIR6V 01
TS210SL 16
Note: Unplug the mains lead from the wall socket prior to any maintenance or
service work.
The saw does not start.
Make sure that the mains lead is undamaged and securely connected to
the wall socket.
Check that the wall socket is live.
The motor overload protection has tripped. Let the motor cool down for
10 minutes and then press the reset button. Refer to the Motor overload
cut-out section above. The saw should now function normally again.
The saw overheats and
the motor overload cut-
out is triggered.
Do not overload the saw by feeding material into the blade too forcefully;
let the saw do the work.
Does the work task exceed the capacity of the saw?
Debris obstructing saw blade. Disconnect the saw from the power supply
and clean it.
Make sure that the air vents of the motor are not covered with dust.
Let the motor cool down for 10 minutes and then press the reset button.
Refer to the motor overload cut-out section above. The saw should now
function normally again.
Poor cutting performance.
Blunt or worn blade. Replace if necessary. Refer to the riving knife and saw
blade section above.
Check that the blade is fitted correctly.
Saw cut not at correct
angle.
Check and adjust the angle.
The work piece binds on
the blade when rip
cutting.
Adjusting the riving knife, refer to the riving knife and saw blade section
above.
The work piece or parts of
it are thrown backwards.
Adjust the riving knife, refer to the riving knife and saw blade section
above.
Feed the entire work piece past the blade before letting go of it (use a
push stick if necessary). Inspect the saw blade regularly, change if
necessary.
Abnormal noise and
vibration.
Check that all parts are correctly assembled and that all screws and nuts
are tight.
Check that the blade is in good condition and is correctly fitted.
Check that the floor is level and that the saw has all four legs squarely on
the floor.
The motor stops, the work
piece gets burn marks
when rip cutting.
The saw blade may be blunt, replace if necessary. Refer to the Riving knife
and saw blade section above.
Do not feed the work piece into the blade too quickly, slow the feed rate.
Adjust the riving knife, refer to the Riving knife and saw blade section
above.
TROUBLESHOOTING

TS210SL 17
LUMBERJACK GUARANTEE
1. Guarantee
1.1 Lumberjack guarantees that for a period of
12 months from the date of purchase the
components of qualifying products (see clauses
1.2.1 to 1.2.8) will be free from defects caused
by faulty construction or manufacture.
1.2. During this period Lumberjack, will repair or
replace free of charge any parts which are
proved to be faulty in accordance with
paragraph 1.1 providing that:
1.2.1 You follow the claims procedure set out in
clause 2
1.2.2 Lumberjack and its authorised dealers are
given reasonable opportunity after receiving
notice of the claim to examine the product
1.2.3 If asked to do so by Lumberjack or its
Authorised dealer, you return the product at
your own cost to Lumberjack’s or supplying
Authorised Dealer’s premises, for the
examination to take place clearly stating the
Returns Material Authorisation number given by
Lumberjack or an Authorised Dealer.
1.2.4 The fault in question is not caused by
industrial use, accidental damage, fair wear and
tear, wilful damage, neglect, incorrect electrical
connection, misuse, or alteration or repair of the
product without approval.
1.2.5 The product has been used in a domestic
environment only
1.2.6 The fault does not relate to consumable
items such as blades, bearings, drive belts, or
other wearing parts which can reasonably be
expected to wear at different rates depending
on usage.
1.2.7 The product has not been used for hire
purposes.
1.2.8 The product has been purchased by you as
the guarantee is not transferable from a private
sale.
2. Claims Procedure
2.1 In the first instance please contact the
Authorised Dealer who supplied the product to
you. In our experience many initial problems with
machines that are thought to be faulty due to
faulty parts are actually solved by correct setting
up or adjustment of the machine. A good
Authorised Dealer should be able to resolve the
majority of these issues much more quickly than
processing a claim under the guarantee. If a
return is requested by the Authorised Dealer or
Lumberjack, you will be provided with a Returns
Material Authorisation number which must be
clearly stated on the returned package, and any
accompanying correspondence. Failure to provide
a Returns Material Authorisation number may
result in item being refused delivery at Authorised
Dealer.
2.2 Any issues with the product resulting in a
potential claim under the guarantee must be
reported to the Authorised Dealer from which it
was purchased within 48 hours of Receipt.
2.3 If the Authorised Dealer who supplied the
product to you has been unable to satisfy your
query, any claims made under this Guarantee
should be made directly to Lumberjack. The Claim
itself should be made in a letter setting out the
date and place of purchase, giving a brief
explanation of the problem which has led to the
claim. This letter should be then sent with proof

TS210SL 18
LUMBERJACK GUARANTEE
of purchase to Lumberjack. If you include a
contact number with this it will speed your claim
up.
2.4 Please note that it is essential that the letter
of claim reaches Lumberjack on the last day of
this Guarantee at the latest. Late claims will not
be considered.
3. Limitation of Liability
3.1 We only supply products for domestic and
private use. You agree not to use the product for
any commercial, business or resale purposes and
we have no liability to you for any loss of profit,
loss of business, business interruption or loss of
business opportunity.
3.2 This Guarantee does not confer any rights
other than these expressly set out above and
does not cover any claims for consequential loss
or damage. This Guarantee is offered as an extra
benefit and does not affect your statutory rights
as a consumer.
4. Notice
This Guarantee applies to all product purchased
from an Authorised Dealer of Lumberjack within
the United Kingdom. Terms of Guarantee may
vary in other countries.