Lumens VC-TR1 User manual

To download the updated software, multilingual manuals,
and Quick Start Guide, please visit Lumens™ website at:
。https://www. /supportMyLumens.com
Please activate your warranty: 。www.MyLumens.com/reg
Important
www.MyLumens.com
1. Product Introduction
3. About the power supply
1.1 Product Overview 1.2 I/O Interface
Panoramic Camera
Copyright ©2020 Lumens Digital Optics Inc. All rights reserved.
Tracking
PTZ Camera
2. Instruction on OUTPUT SWITCH Setting
LED Indicator IR Remote
DIP Switch
Reserved
Hole
USB
SDI
Output Power
(DC12V)
LAN Port
Audio
Input
HDMI
Output RS-232
Input
Power
Switch
Mode
Format
SW
Format
SW
USB
Ethernet
1080p60
1080p50
1080p30
1080p25
720p60
720p50
MENU
OFF
ON
2.1 Factory-preset default is 1080p60.
2
because they cannot be output at
the same time.
2.3 The camera will restart 5 seconds
after modifying the DIP.
2. USB and IP may only choose one,
Router Camera
CAT6 network cable
3.1 Connect the DC 12 V power adapter for power supply.
3.2 Access power by using a router that supports PoE or connecting to a
HUB with an Internet cable.
4. Installation Precautions
4.1 Recommended best tracking target distance
4.2 Recommended best mounting height: 2.2 ~ 2.4 m
: 8~12m
4.3 To install the camera on the wall or ceiling, the accessories could be
bought separately.
5. Camera connection description
CMS Software
Camera
LAN
CAT5e/
network cable
CAT6
The camera supports PoE+(IEEE802.3at)
5100401-50 OCT. 2020
When all the DIP switches are set to ON,
the resolution of the camera is determined
by OSD.
CAT5e/
network cable
CAT6
8m~12m
2.2m~2.4m
Auto-Tracking Camera
Quick Start Guide

www.MyLumens.com
Auto-Tracking Camera
Copyright ©2020 Lumens Digital Optics Inc. All rights reserved.
6.3 Open the LumensCMS software, and add in the camera
Support Windows 7 and later versions
6. Instructions on Software Installation and Tracking Device
6.1 Confirm that the computer and the camera are
in the same network segment
26. Install LumensCMS software
Please download the relevant software from Lumens website
1. Automatically add it in
First, turn on the camera. After opening
the LumensCMS software, the camera
will be automatically added to the list for
about 5~7 seconds. Double-click the
camera to display the screen.
2. Manually add it in
Open the Device Manager page
2.1 Search Device:j[Refresh]>k>l[Add to Device Manager]
m
2.2 Go back to [Live View]page. Double-click the camera added to the list to
display the screen
Click camera
Click
n
6.3 Set tracking parameters
1. Presenter Frame
Operate the PTZ to set the tracking screen. This
setting determines the magnification and the
vertical angle of the PTZ during tracking.
Recommendation: The face shall be in the yellow
auxiliary frame. After straightening the arms, the
best distance between the left and right sides and
the frame is to accommodate at least 1 person.
2. Stage Frame
Operate the PTZ to set the stage screen. When
the camera loses the tracking target, the screen
will automatically switch to the Stage Frame
screen.
3.
Click
Drag the mouse to customize the tracking area
When the target appears in the
the camera will start the tracking.
¡ Everywhere Tracking: After being checked, the
will still be tracked automatically if it is
tracking area frame.
¡ Blocked Area(1-8): Draw the Blocked Area. The
Area can block the motion detection
(but not the face detection).
[Settings]>[Tracking Area]
(green frame),
tracking area,
target
outside the green
Blocked
4. Click to start the tracking.
Quick Start Guide
j
k
l
n
m