Lumiax Shine series User manual

Shine series
Solar Charge Controller
3A/5A 12V
User Manual
www.lumiax.com
Lumiax
Magic your solar life
User Manual_Shine series_HE
CE, Rohs, ISO9001:2015
Subject to change without notice!

Shine series solar controller is especially for solar home
system, with better cost-effective.
It comes with a number of outstanding features,
such as:
Low cost and high reliability design
Clear readable display of charge/discharge and error
description
Four stage charge way: fast, boost, equalization, float
Full automatic electronic protect function
12V system voltage
Temperature compensation
Solar charge controller Shine03/05 User Manual
INFO CHARGE
18
49
90
Page 1 of 2 Pages
This manual gives important recommendations for installing and using and so on. Read it carefully in your own interest please.
Dear Clients,
Thanks for selecting the Shine series solar controller. Please take the time to read this user manual, this will help you to make full
use of many advantages the controller can provide your solar system.
1.Description of Function
2.Safety instructions and waiver of liability
2.1 Safety
①The solar charge controller may only be used in PV
systems in accordance with this user manual and the
specifications of other modules manufacturers. No energy
source other than a solar generator may be connected to
the solar charge controller.
②Batteries store a large amount of energy, never short
circuit a battery under all circumstances. We strongly
recommend connecting a fuse directly to the battery to
protect any short circuit at the battery wiring.
2.2
③Batteries can produce flammable gases. Avoid making
sparks, using fire or any naked flame. Make sure that the
battery room is ventilated.
④Avoid touching or short circuiting wires or terminals. Be
aware that the voltages on special terminals or wires can
be as much as twice the battery voltage. Use isolated
tools, stand on dry ground, and keep your hands dry.
⑤Keep children away from batteries and the charge
controller.
Liability Exclusion
The manufacturer shall not be liable for damages,
especially on the battery, caused by use other than as
intended or as mentioned in this manual or if the
recommendations of the battery manufacturer are
neglected. The manufacturer shall not be liable if there has
been service or repair carried out by any unauthorized
person, unusual use, wrong installation, or bad system
design.
3.Dimensions
4.Installation
The following diagrams provide an overview of the
connections and the proper order.
To avoid any voltage on the wires, first connect the wire to
the controller, then to the battery, panel or load.
Make sure the wire length between battery and controller
is as short as possible.
Recommended minimum wire size: 1.5 mm².
Be aware that the positive terminal of Sshine are
connected together and therefore have the same
electrical potential. If any grounding is required, always do
this on the positive wires.
Connecting capacitive load may trigger short circuit
protection.
5.Starting up the controller
5.1Self Test
As soon as the controller is supplied with battery, it
starts a self test routine. Then the display changes to
normal operation.
5.2System Voltage
The controller is 12V system voltage. As soon as the
battery voltage at the time of start-up is within 10V to 16V,
the controller implies a 12V system.
If the battery voltage is not within the normal operating
rang at start-up, a status display according to the section
Error description occur.
5.3Battery Type
The controller applies to Liquid battery.
INFO CH ARGE
①②
③④⑤⑥

6.LED indications
INFO CH ARGE
Red Green
Model
System voltage
Boost voltage
Equalization voltage
Float voltage
Load disconnect voltage
Load reconnect voltage
Day/Night threshold
Battery type
Max solar voltage
Max battery voltage
Over voltage protection
Dimensions/Weight
Own consumption
Ambient temperature
Max solar/Load current
Shine03 Shine05
12V
3A 5A
14.5V (25℃
14.8V (25℃)
13.7V (25℃)
11.0V
12.5V
5.0V
Liquid
)
30V
25V
15.5V
90 x49 x18 mm / 36g
5mA
-40 ~ +60 ℃
Temperature
compensation
Page 2 of 2 Pages
7.Safety Features
Short circuit
Over current
Over voltage
Over temp.
Reverse
polarity
Solar terminal
Protected
Protected
Protected
Max.30V *3
Battery terminal
Protected
Protected *2
Max. 25V
Load terminal
Protected *1
Switches off
Switches off
with delay
switches off the load if the temperature
reaches the set value.
Switches off
immediately
Reverse
Current
Under
voltage
*1.
*2.Battery must be protected by fuse, or battery will be
permanently damaged.
*3.The solar panel voltage should not exceed this limit for a
long time as voltage protection is done by a varistor.
Controller can protect itself, but loads might be damaged.
!
conditions may cause damage to the controller.
Always remove the error before you continue connecting
the controller.
Warning: The combination of different error
Green
Status
Battery connected，
day detected
Lighted together
(1second)
Equal charging
Battery connected，
night detected
Controller start-up
No battery connected
Red
No faults detected
float charging
Slow flash(1s on/1s off )
Function
Flash(0.4s/0.4s)
Fast flash(0.1s/0.1s)
On
Off
Off
Red
Green
LED
Slow flash(1s on/1s off )
On
Short circuit
Over current
Over temp.
Under voltage
8.Technical Data
-4.17mV/K per cell (boost,
equalization)，
-3.33mV/K per cell (float)
Solar charge controller Shine03/05 User Manual