Lumiax Shine -EU Series User manual

TM
Shine -EU series
Solar charge controller
10A/15A
User Manual
User Manual_Shine-EU series_MG
CE, Rohs, ISO9001:2015
Subject to change without notice!

Solar charge controller
Solar Charge Controller Shine-EU Series User Manual
Low cost and high reliability design, suitable for 12V/24V
system
Load output can be controlled by switch
Work mode optional: system, D2D
Clear readable display of charge/discharge/error description
Four stage charge way: fast, boost, equalization, float
Full automatic electronic protect function
USB interface
Temperature compensation
Gel, Liquid and Li battery for selection
Shine-E series solar controller is specifically designed to
meet the needs of solar home systems. It provides the best
cost-effective.
It comes with a number of outstanding features, such as:
This manual gives important recommendations for installing and using and so on. Read it carefully in your own interest please.
4.Installation
!Remark: If the device is used in a vehicle which has the
battery negative on the chassis, loads connected to the
controller must not have an electric connection to the
car body, otherwise the Low Voltage disconnect and
electronic fuse functions of the controller are short
2.Safety instructions and waiver of liability
2.1 Safety
①The solar charge controller may only be used in PV
systems in accordance with this user manual and the
specifications of other modules manufacturers. No
energy source other than a solar generator may be
connected to the solar charge controller.
②Batteries store a large amount of energy, never short
circuit a battery under all circumstances. We strongly
recommend connecting a fuse directly to the battery to
protect any short circuit at the battery wiring.
2.2
③Batteries can produce flammable gases. Avoid
making sparks, using fire or any naked flame. Make sure
that the battery room is ventilated.
④Avoid touching or short circuiting wires or terminals.
Be aware that the voltages on special terminals or wires
can be as much as twice the battery voltage. Use
isolated tools, stand on dry ground, and keep your
hands dry.
⑤Keep children away from batteries and the charge
controller.
Liability Exclusion
The manufacturer shall not be liable for damages,
especially on the battery, caused by use other than
as intended or as mentioned in this manual or if the
recommendations of the battery manufacturer are
neglected. The manufacturer shall not be liable if
there has been service or repair carried out by any
unauthorized person, unusual use, wrong
installation, or bad system design.
1.Description of Function
Dear Clients,
TM
Thanks for selecting the Shine -EU series solar controller. Please take the time to read this user manual, this will help you to
make full use of many advantages the controller can provide your solar system.
3.Dimensions
The following diagrams provide an overview of the
connections and the proper order.
To avoid any voltage on the wires, first connect the wire to
the controller, then to the battery, panel or load.
Make sure the wire length between battery and controller
is as short as possible.
Recommended minimum wire size:10A:2.5mm,15A:4mm2
Be aware that the positive terminal of Shine are connected
together and therefore have the same electrical potential.
If any grounding is required, always do this on the positive
wires.
Connecting capacitive load may trigger short circuit
protection.
Page 1 of 5 pages
①②
③④⑤⑥
66
33
Unit:mm
126
4
12
φ4
φ4
43.5
4*2
118.2

The controller is equipped with 5 LEDS.
In normal operation, the controller shows charge or discharge
status, battery capacity and load status.
6.1 Battery Capacity display：
!The percentage corresponds to the available energy
until low voltage disconnect in relation to a fully
charged battery.
Red On, Energy of Battery <25%
Yellow On, Energy of Battery 25~75%
Green On, Energy of Battery >75%
Red
Yellow
Green
6.2 C Error （INFO）：harge & display
Red Green
INFO Green On, it is charging, otherwise it is discharging;
INFO Red On, indicating the failure of instructions, see the
following Error description.
Page 2 of 5 pages
5.Starting up the controller
5.1Self Test
As soon as the controller is supplied with battery, it
starts a self test routine. Then the display changes to
normal operation.
5.2System Voltage
Shine152 EU can automatically recognize the 12/24v
system voltage. If the battery voltage is less than
15.5v at startup, the controller will recognize it as a
12V system; If the battery voltage is between 20V and
31v when starting, the controller will recognize it as a
24V system, otherwise the controller will display an
error state. Please refer to the fault description to find
out the cause.
5.3Battery Type
The Shine-EU series controller applies to Liquid and
Gel battery, the factory default setting is suitable for
liquid battery.
The Shine-EULi series controller applies to 3s Lithium
and 4s LiFePO4 battery.
6.Display Functions
Over current/
short circuit
of loads
Solar array faulty
or wrong polarity
Battery has
low capacity
Error Display Reason Remedy
Red LED
is on
Red LED is
flashing(1s)
Red LED
is on
Green LED
is off
Load will reconnect
as soon as battery
is recharged
Switch off all loads.
Remove short
circuit.
Check battery
wires, fuse and
battery.
Change batter y
Remove faulty
connection/
reverse polarity
Batter y red
LED is on;
Info red and
green LED
are on
Does not
recognize
the system
voltage
Charge or discharge
the battery to make
the voltage within
the normal range
(about 5V~15V)
Loads
are
not
supplied
Battery voltage
too high
(>15.5V/31V)*
Battery is
empty after
a short time
Over
voltage
protection
Battery is
not being
charged
during
the day
Battery wires or
battery fuse
damaged, battery
has high resistance
The battery
voltage is not
within the normal
operating rang
at start-up
Check if other
sources overcharge
the battery.
If not, controller
is damaged.
Red(INFO)
and
Green(Bat.)
LED are on.
Red Green
Over temperature
Red LED is
flashing(0.5s)
After temperature
reduces, the load
opens automatically.
七、蓄电池放电保护
To protect the battery from being deeply
discharged, the Shine-E series controller will
automatically cut off the load when the battery
voltage down to 11.0V/22.0V.
!
protection, it will restore reaching the reconnect
voltage(12.5V/25.0V).
In D2D mode, if the controller goes into low voltage
7.LVD、USB interface
7.1 Low voltage protect
7.2 USB interface
USB interface provides an output voltage 5V 2A of current,
for charging mobile phones and other smart devices.
Battery voltage
is low
Solar Charge Controller Shine-EU Series User Manual
High voltage protection voltage of lithium battery:
overcharge protection voltage +0.2v

!
at the same time, the new set immediately effective.
2. After entering the programming mode without a graceful
exit, the controller automatically exits programming mode
after 3min, and the settings are not saved.
1. If programming success, INFO red and green led flash
!
conditions may cause damage to the
controller.
Always remove the error before you continue
connecting the controller.
Warning: The combination of different error
八、安全特性及故障描述
9.Safety Features
Warning: PV shall not be short circuited during
charging, otherwise the controller will be damaged.
*3 Battery must be protected by fuse, otherwise
battery will be damaged.
*4 The solar panel voltage should not exceed this limit
for a long time as voltage protection is done by a
varistor.
*4 Please refer to "ten. technical parameters" to obtain
the maximum voltage that different types of solar
panels can withstand.
*5 Please refer to "ten. Technical parameters" to obtain
the maximum voltage that different types of batteries
can withstand.
Short circuit
Over current
Over voltage
Over temp.
Reverse
polarity
Solar terminal
Protected
2
Protected*
Protected
4
Max.50V *
Battery terminal
Protected
3
Protected *
5
Max. 35V*
Load terminal
1
Protected *
Switches off
with delay
switches off the load if the temperature
exceeds the set value.
Switches off
immediately
Reverse
Current
Under
voltage
五、控制器的启动
8.Key Function
8.1 Load Switch
In system mode, by pressing the button can control
the load output, once press the button, the load
output will be changed between on and off.
8.2 Test Function
In D2D mode, during daytime the testing function
can help the user to verify correct installation or for
system trouble shooting.
Short pushing the button will light up the lamp
which is connected to the load terminals. The lights
will be on in the day for 1 minute intervals. Within 1
minute the lights can be turned off via pushing
Button.
8.3Programming Function
You enter the programming mode with a long push
on the button, then the BATTERY Green and Yellow
LED will be on, the different states of the INFO led
indicator different battery types and work modes.
The factory default setting is Liquid batter y and
System mode.
The programming menu structure is described on the
follow.
D2D(Dusk to Dawn)
Threshold
Sunset
Sunrise
System
Light On
Threshold
Light On
Light Off Light Off
Programming menu is shown below
Enter
Programming Liquid/ ,
INFO red led on
(Default setting)
4sLiFePO4
Short Push ( <1s ) Long Push ( >3s )
Enter programming mode，
BATTERY Green and Yellow LED on
Gel / ,
INFO red led flash
8s LiFePO4
System mode,
INFO green led on,
(Default setting)
D2D mode,
INFO green led
flash
Exit Programming
Page 3 of 5 pages
Solar Charge Controller Shine-EU Series User Manual
Battery types
Work modes
*1 Controller can protect itself, but loads might be
damaged.
*2 When the PV is not charged, the solar terminal will
be short circuited and the controller will not be
damaged.
Switches off

Model
System voltage
Max solar or load current
Fast voltage
Boost voltage
Equalization voltage
Float voltage
Charging voltage target
charging voltage recovery
Load disconnect voltage
Load reconnect voltage
Over voltage protection
Work mode
Battery type
Temperature compensation
Max voltage at solar terminals
Max voltage at battery terminals
Dimensions/Weight
Max. wire size
Self consumption
Ambient temperature
Protection level
USB interface
Shine1012-EU Shine1012-EULi
12V
10A
14.0V (25℃)
14.5V (25℃)
14.8V (25℃)（Liquid）
13.7V (25℃)
/ 12.5/14.4V
/ 12.2/14.0V
11.0V 9.9/11.2V
12.5V 9.0/12.0V
15.5V Charging voltage target+0.2V
System, D2D(Dusk to Dawn)
Liquid(default)/Gel default)
-4.17mV/K per cell (boost, equalizatio-n)，
-3.33mV/K per cell (float)
25V
20V
126*66*33mm / 110g
4mm²
6mA
-35℃ ~ +60 ℃
IP22
5V, 2A
3s Lithium/4s LiFePO4(
Page 4 of 5 pages
10.Technical Data
Solar Charge Controller Shine-EU Series User Manual
/
/
/
/
/

Model
System voltage
Max solar or load current
Fast voltage
Boost voltage
Equalization voltage
Float voltage
Charging voltage target
charging voltage recovery
Load disconnect voltage
Load reconnect voltage
Over voltage protection
Work mode
Battery type
Temperature compensation
Max voltage at solar terminals
Max voltage at battery terminals
Dimensions/Weight
Max. wire size
Self consumption
Ambient temperature
Protection level
USB interface
Shine1524-EU Shine1524-EULi
12V/24V
15A
14.0V/28.0V (25℃)
14.5V /29.0V(25℃)
14.8V /29.6V(25℃)（Liquid）
13.7V/27.4V (25℃)
/ 14.4V/28.8V
/ 14.0V /28.0V
11.0V 11.2V/22.4V
12.5V 12.0V/24.0V
15.5V Charging voltage target+0.2V
System, D2D(Dusk to Dawn)
Liquid/Gel (default)default)/8
-4.17mV/K per cell (boost, equalizatio-n)，
-3.33mV/K per cell (float)
25V/50V
20V
126*66*33mm / 110g
4mm²
6mA
-35℃ ~ +60 ℃
IP22
5V, 2A
4s LiFePO4( s LiFePO4
/
/
/
/
/
Page 5 of 5pages