lumishore Lumi-Link Safety guide

Lumi-Link Command Center - Setup and User Guide
First Time use…
When first installed the system needs to be setup. Setup is a quick and easy process and is only performed upon
initial installation or after a firmware upgrade.
Setup discovers lights that are attached to the network and allows the user to select between a Single Zone or
Multizone mode display.
Underwater lightscan be setup as a “Single zone”or as a “Multizone”
For Underwater and Above water installations choose Multizone Mode as per the following examples….
Configuration examples…
Exmple 1; Single Zone –
UW lights Only
Example 2; Multizone –UW lights, Starboard,
Port, Transom.
Example 3; Multizone –UW lights &
Lumishore LUX –E.g. downlights, strip
lights and courtesy lights.
www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 |[phone] | [e-mail] 1
45-0138 - Rev 1

www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 |[phone] | [e-mail] 2
www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 |[phone] | [e-mail]
The position of the lights around the vessel can also be setup. This ensures
that sweep mode works in the correct order. (Above water zones do not
require position information but can be set if desired).
Light Discovery Process…
Upon first installation and before choosing single vs multizone, the lights connected to the Lumi-link network need
to be discovered.
Perform these steps on first use or if new lights have been added or deleted from the Lumi-link network.
Select “Setup” Icon
Select “Preferences”
Select “System Setup”
Selecet “Light Discovery”
The system discovers ALL lights
attached
Check that all lights have been found
Note –if the number of lights found does not match the expected number, check connections and that each light has
power.

www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 |[phone] | [e-mail]
www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 |[phone] | [e-mail] 3
Single mode setup…(Skip if setting up as Multizone)
Select Setup as “Single Zone”
The next step allows the position of the underwater lights to be set around
the vessel. This ensures the lights are sent information in the correct order
and color change in the correct sequence.
To set the positions use the following steps and the example positions
shown below.
“Wink Light”to identify it on the vessel –the
light will flash RGB
Use the diagram above as a guide, edit the
light position relative to the vessel.
Repeat for all Lights and then press Save
Light Set up is now complete! The lights can be controlled from the Lumi-link control panel.
The position of the lights around the vessel can also be setup. This ensures
that sweep mode works in the correct order. (Above water zones do not
require position information but can be set if desired).
Light Discovery Process…
Upon first installation and before choosing single vs multizone, the lights connected to the Lumi-link network need
to be discovered.
Perform these steps on first use or if new lights have been added or deleted from the Lumi-link network.
Select “Setup” Icon
Select “Preferences”
Select “System Setup”
Selecet “Light Discovery”
The system discovers ALL lights
attached
Check that all lights have been found
Note –if the number of lights found does not match the expected number, check connections and that each light has
power.

www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 |[phone] | [e-mail] 4
www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 |[phone] | [e-mail]
Lumi-link Control Panel…

www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 |[phone] | [e-mail]
www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 |[phone] | [e-mail] 5
Multi-Zone Setup and Create new Zone…
Select “Setup as Multi Zone”
Lighting zones can be created for different areas of the vessel. A zone could contain
underwater lights, strip lights, downlights, courtesy lights or a mixture of the above.
The zone names can be edited and an icon selected for easy identification.
Select Setup Icon
Select Create Zone
Rename the zone and choose a suitable icon
Use the Name of the light or “wink Light” to identify
each light on the network. Select which lights to
allocate to the Zone and then Save the selection.
(Optional) –Light positions can be assigned. This
ensures the sweep mode will work in the correct
sequence. Eg for Underwater lights.
The Lights in this zone will appear, change their
position as required and then press save.
NOTE: A light can exist in 1 zone only, it cannot be placed in mutiple zones.
The new zone will appear on the Zone homescreen.
Press the power icon to turn each Zone on/off, Press
the RHS of tab to enter Main control page.
Main control page….
Lumi-link Control Panel…

To Edit or delete a Zone…
To Edit or Delete this zone long Press (>3sec) the
Zone tab.
Rename, change icon, re-assign lights, Save,
Cancel or Delete zone.
Creating lighting Scenes…
Once each zone has been setup the user can select the colour, effect and intensity for each of these lighting zones.
These preferences can then be saved as a lighting “Scene”.
Scenes can include a single zone or mutiple zones, they can also include a zone “set to off”.
More than one scene can be active at a time, if zones are shared between scenes, the Zones will follow the last
Scene command.
In the example below each of the 5 zones has been allocated a different colour and Zone 5 is set to Off. To create
this as a new scene e.g. “Docking Mode” follow the steps below….
Create the 5 separate lighting zones and select
the desired color & intensity for each one.
Select “Save as Scene” from the Setup menu
Rename the scene and select an icon. Ensure
the zones to be included are checked.
Hold for >3 Sec
www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 |[phone] | [e-mail] 6
www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 |[phone] | [e-mail]

www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 |[phone] | [e-mail]
www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 |[phone] | [e-mail] 7
To Edit or delete a Zone…
To Edit or Delete this zone long Press (>3sec) the
Zone tab.
Rename, change icon, re-assign lights, Save,
Cancel or Delete zone.
Note: When a zone is created, edited or deleted all zones default to green at 25% intenisty. This indicates that any
changes have been successful.
Creating lighting Scenes…
Once each zone has been setup the user can select the colour, effect and intensity for each of these lighting zones.
These preferences can then be saved as a lighting “Scene”.
Scenes can include a single zone or mutiple zones, they can also include a zone “set to off”.
More than one scene can be active at a time, if zones are shared between scenes, the Zones will follow the last
Scene command.
In the example below each of the 5 zones has been allocated a different colour and Zone 5 is set to Off. To create
this as a new scene e.g. “Docking Mode” follow the steps below….
Create the 5 separate lighting zones and select
the desired color & intensity for each one.
Select “Save as Scene” from the Setup menu
Rename the scene and select an icon. Ensure
the zones to be included are checked.
Hold for >3 Sec

Password Protect (Optional)…
Once setup, Zones and Scenes have been created, they can be password protected to prevent accidental editing or
deletion. The default password is “0000”This can be changed within the same menu.
Select Setup Icon
Select preferences
Select Lock/Unlock
Enter the Default Password: 0000
To change the password select “Set
Password”.
To Lock the system select “Lock”
When locked, Setup, create zone & create
Scenes and long press edits are greyed out &
non functional. Repeat the process to Unlock
the system.
www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 |[phone] | [e-mail] 8
www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 |[phone] | [e-mail]
Control from Smart Device or Web browser…
Ensure your smart device is connected the same network as the Lumi-link Command centre. Depending on
instalation this may be the vessels onboard WIFI, the MFD WIFI or the Lumishore Lumi-Link Display WIFI. The
following example shows the Lumi-link Command center connected to the MFD wifi….
Ensure the MFD wifi is switched on and the smart device is connected to it.
Using the MFD –launch the Lumi-link app
Select Setup Icon
Select preferences
Select About Screen
Make a note of the IP address
Note: it may be different to the example
below
Type the IP address into the browser on the
smart device
You can now control the lights remotley
using the Lumi-Link app.
Note - from time to time the MFD or network router may change the IP address automatically. If the Lumi-link app
does not display ensure you are connected to the correct wifi network and that you have entered the correct IP
address.

Password Protect (Optional)…
Once setup, Zones and Scenes have been created, they can be password protected to prevent accidental editing or
deletion. The default password is “0000”This can be changed within the same menu.
Select Setup Icon
Select preferences
Select Lock/Unlock
Enter the Default Password: 0000
To change the password select “Set
Password”.
To Lock the system select “Lock”
When locked, Setup, create zone & create
Scenes and long press edits are greyed out &
non functional. Repeat the process to Unlock
the system.
www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 |[phone] | [e-mail]
www.Lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 |[phone] | [e-mail] 9
Control from Smart Device or Web browser…
Ensure your smart device is connected the same network as the Lumi-link Command centre. Depending on
instalation this may be the vessels onboard WIFI, the MFD WIFI or the Lumishore Lumi-Link Display WIFI. The
following example shows the Lumi-link Command center connected to the MFD wifi….
Ensure the MFD wifi is switched on and the smart device is connected to it.
Using the MFD –launch the Lumi-link app
Select Setup Icon
Select preferences
Select About Screen
Make a note of the IP address
Note: it may be different to the example
below
Type the IP address into the browser on the
smart device
You can now control the lights remotley
using the Lumi-Link app.
Note - from time to time the MFD or network router may change the IP address automatically. If the Lumi-link app
does not display ensure you are connected to the correct wifi network and that you have entered the correct IP
address.