Lunos AB 30/60 User manual

1
Installation Instructions
Exhaust air fan for the de-centralized Ventilation System
Type AB 30/60
- Please pass on to User -
Installation of fan
as extractor hood is
not admissible
Installation in section 1 in
bathrooms and shower
rooms is admissible pursu-
ant to VDE 100.
Ventilation
Section 1
Section 2
2.25 m
Section 0
Contents:
Notes on these Instructions
Safety Instructions
Technical Data, Disposal
Installation Example
Shipment units
Assembly—Mounting Pipe
Assembly _ Motor unit and electrical Connection
Filter change, Cleaning
Complete Sets, Additional / Spare Parts
Page:
1
1
2
2
2
3
4
6
6
Notes on these Instructions
 Before installing, read these instructions carefully and completely! You must observe the general safety instructi-
ons and the warning symbols with notes in the text
 These instructions are to be passed on to the user after installation (tenant, owner, property management etc.)
Symbols used in these instructions:
Caution! Installation and assembly work is only to be executed when power supply has been isolated! The
ventilation unit is insulated pursuant to Protection Class II, protective earth connection is not required!
This symbol warns you of an injury risk
This symbol warns you of an injury risk from electricity
Safety Instructions
Attention! The electrical conection must be installed by authorized skilled staff pursuant to the valid VDE
0100!
Attention! This unit must not be operated by children and persons (filter change/cleaning) who are not able to
operate it safely on account of their physical, sensorical or mental capacity or due to their inexperience or lack
of know-how.
In the case of fans for exhaust air operation, a functioning back-flow of outside air must always be ensured

2
Technical Data; Disposal
Electrical Connection
Power supply: 115/230 V AC 50 /60Hz
Power consumption: Protection Class: II
Low level (30 m³/h) 1,6 W Protection Type: IP 44
High level (60 m³/h) 5 W
Dispose of the packaging correctly sorted. If you wish to throw away your ventilation unit, dispose in accor-
dance with current regulations. In accordance with the Electrical and Electronic Equipment Act (ElektroG),
you can return this unit free of charge to your local waste disposal center.
Installation Example
Shipment units Check the delivery for completeness and perfect condition!
Mounting pipe External grille
Pipe DA 160 mm
Plaster protection
Motor unit Inside panel
Sound insulation
Motor with casing
20 75 130 18
98,5
Minimum length 243
Dimensions in mm
Mounting pipe, external grille, motor unit and inside panel are supplied as a complete set (refer to p. 6) incl. installati-
on instructions in accordance with the color of the external grille (white, light grey or red brown).

3
Other external grilles available, on request!
Assembly - Mounting Pipe
Prepare wall openings for the mounting pipe
(e.g. via core drilling, drilling bit Ø162 mm). If
necessary, shorten the pipe to the installation
length required (min. 243 mm). Check for any
projection of the pipe on both sides to bridge
the plaster thickness (after plastering, the
pipe must be flush with the plaster or flush
with the wall or insulation in the case of exter-
nal grilles to be plastered). Insert the pipe
and seal it all around (mounting adhesive
Order No. 038 733).
Apply internal and external plaster. In the ca-
se of an outer seal to be plastered, first repla-
ce the plaster protective cover with the exter-
nal seal.
Remove the plaster protection cover outside.
Mount the external grille using the integrated
claw fasteners (tighten the screws).
①
②
➂
inside
inside outside
outside
Plaster protection
Tighten the screws and claw fasteners
3 mm

4
Assembly - Motor unit and electrical Connection
Slit the cable duct and pipe (2 cm deep).
Only slit the pipe vertically or horizontally!
Insert the mains cable (e.g. 3x1.5 mm²) at
an appropriate length into the pipe.
Only slit the pipes
in these four sec-
tions.
vertical
horizontal
Cover and insulate the mains cable as il-
lustrated. Lead it through the protective
sleeve of the motor and fix it to the cable
strain relief after the motor has been con-
nected to the mains (connection diagram,
see below). Screw the screw cap for the
electrical connection onto the motor.
Safety Instructions:
Caution! Assembly work involving the ventilation unit must only be executed when all poles of the power supply
have been disconnected!
Before connecting the ventilation unit to the power supply, make sure all connection lines are dead!
(Separation from mains with at least 3mm contact opening, e.g. electric fusing isolating all poles).
Every circuit which is part of this ventilation system must be equipped with residual current protection (e.g.
RCD switch)!
Electrical connections must be made by qualified staff!
Additional installations and electrical components in this ventilation system are not admissible!
Connection diagrams
N
L
N
L
N
L
30 m³/h Continuous operation
60 m³/h with light switch
30 m³/h ON/OFF 60 m³/h ON/OFF
180 mm

5
Insert the sound insulation (if necessary,
slit for better positioning of the power lead)
and the motor unit into the mounting pipe.
Insert internal seal with filter, snap internal
cover into place in open position! Finished!
open
closed

6
E 136/01.12
LUNOS Lüftungstechnik GmbH
für Raumluftsysteme
Wilhelmstr. 31
13593 Berlin
Tel.: 0 30 / 36 20 01 - 0
Fax: 0 30 / 36 20 01 - 89
Email: [email protected]
Internet: http://www.lunos.de
Filter change date Planned filter change Filter type used
Please record the filter changes you have made here:
Filter Change
Check the filter every 3 months for soi-
ling. Clean or replace, if required. Never
operate the unit without a filter.
Remove inside cover. Remove filter,
insert new or cleaned filter (the filter can
be cleaned e.g. with washing-up liquid),
attach inside cover.
The ventilation openings must not be
covered or concealed.
Cleaning
Wipe the inside cover and the masking frame clean with a dry, soft cloth, if required.
Filter change and cleaning must not be executed by children or persons not able to execute such work
safely on account of their physical, sensorical or mental capacity or due to their inexperience or lack of
know-how.
Additonal parts / Spare parts
Filter
Inside cover compl.9/IBE Order No.: 039 851
Spare filters 9/FIB3R pack of 3 Order No.: 037 214
External grille:
Type 1/WE 180 white Order No.: 039 852
Type 1/GE 180 light grey Order No.: 039 853
Type 1/RE 180 red-brown Order No.: 039 854
Type 1/BE 180 sanded Order No.: 039 917
External grille for plastering, on request
Complete sets
AB 30/60 External grille white Order No.: 039 904
AB 30/60 External grille light grey Order No.: 039 905
AB 30/60 External grille red-brown Order No.: 039 906