Luxul AGS-1016 User manual

Fold Fold Fold
READ ME FIRST
QUICK INSTALL GUIDE
16-Port Gigabit Switch
AGS-1016
Includes:
16-Port Gigabit Switch
Rack Mount Kit
Rubber Feet
Power Cord
SETUP AND CONFIGURATION
1Physical Installation
The AGS-1016 can be rack-mounted or used as a desktop switch. Install the
AGS-1016 in a stable/safe place to avoid any possible damage. Avoid placement
in direct sunlight. Do not place heavy articles on the AGS-1016 and verify the
ground connection of the outlet is functioning properly.
Desktop/Shelf Installation
For desktop/shelf installation, attach the four rubber feet to the corner inden-
tations on the bottom of the AGS-1016, then place the switch horizontally on
a solid, level platform.
Rack Installation
Use the included L brackets for convenient installation in a 19-inch server or
audio/video rack. Use four screws to attach the L-shaped brackets on both
sides of the AGS-1016 as shown below, then install the switch horizontally in the
rack. Use your desired hardware to ax the switch brackets to the rack.
Attach Feet for Desktop Installation Install Brackets for Rack-Mounting
2Connecting Ethernet and Power
Ethernet and Power Connections
Use any RJ-45 to connect the AGS-1016 to an Ethernet-enabled device,
including servers, routers or other switches. No crossover cable is necessary.
The AGS-1016 supports 10/100/1000 Mbps Ethernet; 10/100 Mbps half/
full-duplex mode and 1000 Mbps full-duplex mode.
Use the included power cable to connect the AGS-1016 to a surge protected
outlet. The AC input socket and a power switch are on the rear panel. The
built-in power supply supports 100~240VAC at 50/60Hz.
cCAUTION: Use only the correct power cord for your environment.
Any voltage other than standard 100/240 will result in
damage to the AGS-1016.
Sales
P: 801-822-5450
E: [e-mail]
Technical Support
P: 801-822-5450 Option 3
E: [e-mail]
LUX-QIG-AGS-1016-v4 06271701
Copyright and Trademark Notices
No part of this document may be modified or adapted in any way, for any purposes without permission
in writing from Luxul. The material in this document is subject to change without notice. Luxul reserves
the right to make changes to any product to improve reliability, function, or design. No license is
granted, either expressly or by implication or otherwise under any Luxul intellectual property rights. An
implied license only exists for equipment, circuits and subsystems contained in this or any Luxul product.
© Copyright 2017 Luxul. All rights reserved. The name Luxul, the Luxul logo, the Luxul logo mark and
Simply Connected are all trademarks and or registered trademarks of Luxul Wireless, Inc. All other
trademarks and registered trademarks are property of their respective holders.

Fold Fold Fold
READ ME FIRST
QUICK INSTALL GUIDE
16-Port Gigabit Switch
AGS-1016
Includes:
16-Port Gigabit Switch
Rack Mount Kit
Rubber Feet
Power Cord
SETUP AND CONFIGURATION
1Physical Installation
The AGS-1016 can be rack-mounted or used as a desktop switch. Install the
AGS-1016 in a stable/safe place to avoid any possible damage. Avoid placement
in direct sunlight. Do not place heavy articles on the AGS-1016 and verify the
ground connection of the outlet is functioning properly.
Desktop/Shelf Installation
For desktop/shelf installation, attach the four rubber feet to the corner inden-
tations on the bottom of the AGS-1016, then place the switch horizontally on
a solid, level platform.
Rack Installation
Use the included L brackets for convenient installation in a 19-inch server or
audio/video rack. Use four screws to attach the L-shaped brackets on both
sides of the AGS-1016 as shown below, then install the switch horizontally in the
rack. Use your desired hardware to ax the switch brackets to the rack.
Attach Feet for Desktop Installation Install Brackets for Rack-Mounting
2Connecting Ethernet and Power
Ethernet and Power Connections
Use any RJ-45 to connect the AGS-1016 to an Ethernet-enabled device,
including servers, routers or other switches. No crossover cable is necessary.
The AGS-1016 supports 10/100/1000 Mbps Ethernet; 10/100 Mbps half/
full-duplex mode and 1000 Mbps full-duplex mode.
Use the included power cable to connect the AGS-1016 to a surge protected
outlet. The AC input socket and a power switch are on the rear panel. The
built-in power supply supports 100~240VAC at 50/60Hz.
cCAUTION: Use only the correct power cord for your environment.
Any voltage other than standard 100/240 will result in
damage to the AGS-1016.
Sales
P: 801-822-5450
E: [e-mail]
Technical Support
P: 801-822-5450 Option 3
E: [e-mail]
LUX-QIG-AGS-1016-v4 06271701
Copyright and Trademark Notices
No part of this document may be modified or adapted in any way, for any purposes without permission
in writing from Luxul. The material in this document is subject to change without notice. Luxul reserves
the right to make changes to any product to improve reliability, function, or design. No license is
granted, either expressly or by implication or otherwise under any Luxul intellectual property rights. An
implied license only exists for equipment, circuits and subsystems contained in this or any Luxul product.
© Copyright 2017 Luxul. All rights reserved. The name Luxul, the Luxul logo, the Luxul logo mark and
Simply Connected are all trademarks and or registered trademarks of Luxul Wireless, Inc. All other
trademarks and registered trademarks are property of their respective holders.

Fold Fold Fold
READ ME FIRST
QUICK INSTALL GUIDE
16-Port Gigabit Switch
AGS-1016
Includes:
16-Port Gigabit Switch
Rack Mount Kit
Rubber Feet
Power Cord
SETUP AND CONFIGURATION
1Physical Installation
The AGS-1016 can be rack-mounted or used as a desktop switch. Install the
AGS-1016 in a stable/safe place to avoid any possible damage. Avoid placement
in direct sunlight. Do not place heavy articles on the AGS-1016 and verify the
ground connection of the outlet is functioning properly.
Desktop/Shelf Installation
For desktop/shelf installation, attach the four rubber feet to the corner inden-
tations on the bottom of the AGS-1016, then place the switch horizontally on
a solid, level platform.
Rack Installation
Use the included L brackets for convenient installation in a 19-inch server or
audio/video rack. Use four screws to attach the L-shaped brackets on both
sides of the AGS-1016 as shown below, then install the switch horizontally in the
rack. Use your desired hardware to ax the switch brackets to the rack.
Attach Feet for Desktop Installation Install Brackets for Rack-Mounting
2Connecting Ethernet and Power
Ethernet and Power Connections
Use any RJ-45 to connect the AGS-1016 to an Ethernet-enabled device,
including servers, routers or other switches. No crossover cable is necessary.
The AGS-1016 supports 10/100/1000 Mbps Ethernet; 10/100 Mbps half/
full-duplex mode and 1000 Mbps full-duplex mode.
Use the included power cable to connect the AGS-1016 to a surge protected
outlet. The AC input socket and a power switch are on the rear panel. The
built-in power supply supports 100~240VAC at 50/60Hz.
cCAUTION: Use only the correct power cord for your environment.
Any voltage other than standard 100/240 will result in
damage to the AGS-1016.
Sales
P: 801-822-5450
E: [e-mail]
Technical Support
P: 801-822-5450 Option 3
E: [e-mail]
LUX-QIG-AGS-1016-v4 06271701
Copyright and Trademark Notices
No part of this document may be modified or adapted in any way, for any purposes without permission
in writing from Luxul. The material in this document is subject to change without notice. Luxul reserves
the right to make changes to any product to improve reliability, function, or design. No license is
granted, either expressly or by implication or otherwise under any Luxul intellectual property rights. An
implied license only exists for equipment, circuits and subsystems contained in this or any Luxul product.
© Copyright 2017 Luxul. All rights reserved. The name Luxul, the Luxul logo, the Luxul logo mark and
Simply Connected are all trademarks and or registered trademarks of Luxul Wireless, Inc. All other
trademarks and registered trademarks are property of their respective holders.

Fold Fold Fold
3Connecting Devices
Use an Ethernet cable to connect the AGS-1016 to a device as shown below.
Luxul recommends at least Cat-5e unshielded twisted pair (CAT5e UTP)
cabling. To ensure best performance and stable data transmission at 1000
Mbps, use Category-6 unshielded twisted pair (CAT6 UTP).
The AGS-1016 automatically adjusts to the speed and duplex of the
connected device.
Connecting the AGS-1016 to a Device
When a device is properly connected and powered, the Link/Activity LED
for the device port lights up. Refer to the Hardware Operation section for
indicator definitions and troubleshooting.
4Connecting to a Router or Other Switch
Use an Ethernet cable to connect the AGS-1016 to a router or other switch as
shown below. The AGS-1016 automatically adjusts to the speed and duplex of
the connected switch or router, so uplink cables are not necessary.
Connecting the AGS-1016 to Router or Switch
When a router or switch is properly connected, the Link/Activity LED for each
port lights up. Refer to the Hardware Operation section for indicator definitions
and troubleshooting.
5Hardware Operation
The front panel of the AGS-1016 switch features one Power LED as well as a
Link/Activity LED for each port. The back panel of the switch includes (16)
10/100/1000 Mbps RJ-45 ports, a power connector, and a switch to select blue
or green front-panel LEDs. Each Ethernet port has one LED to indicate Link/
Activity as well as connection speed.
AGS-1016 Front Panel
Status Indicators
The following table describes the LED functionality for both front and
back indicators:
Front
Indicator State Description
Power On The AGS-1016 is switched on.
O AGS-1016 is switched o or not connected to AC
power. Check power connections and power switch
at on the rear of the unit.
Link/Act On Device connected to the port.
Flashing Port is receiving or transmitting data.
O No device connected to the port or the device is o.
Back
Indicator State Description
Speed/
Link/Act
Green Gigabit device connected to the port.
Amber 10/100Mbps device connected to the port.
Flashing Port is receiving or transmitting data.
O No device connected to the port or device is o.
SELECTING FRONT-PANEL LED COLOR
Use the switch on the rear panel of the AGS-1016 to select either blue or
green for the Power and System LEDs on the front panel to best match the
equipment in the rack where the Switch is sharing space.
AGS-1016 Selector Switch

Fold Fold Fold
3Connecting Devices
Use an Ethernet cable to connect the AGS-1016 to a device as shown below.
Luxul recommends at least Cat-5e unshielded twisted pair (CAT5e UTP)
cabling. To ensure best performance and stable data transmission at 1000
Mbps, use Category-6 unshielded twisted pair (CAT6 UTP).
The AGS-1016 automatically adjusts to the speed and duplex of the
connected device.
Connecting the AGS-1016 to a Device
When a device is properly connected and powered, the Link/Activity LED
for the device port lights up. Refer to the Hardware Operation section for
indicator definitions and troubleshooting.
4Connecting to a Router or Other Switch
Use an Ethernet cable to connect the AGS-1016 to a router or other switch as
shown below. The AGS-1016 automatically adjusts to the speed and duplex of
the connected switch or router, so uplink cables are not necessary.
Connecting the AGS-1016 to Router or Switch
When a router or switch is properly connected, the Link/Activity LED for each
port lights up. Refer to the Hardware Operation section for indicator definitions
and troubleshooting.
5Hardware Operation
The front panel of the AGS-1016 switch features one Power LED as well as a
Link/Activity LED for each port. The back panel of the switch includes (16)
10/100/1000 Mbps RJ-45 ports, a power connector, and a switch to select blue
or green front-panel LEDs. Each Ethernet port has one LED to indicate Link/
Activity as well as connection speed.
AGS-1016 Front Panel
Status Indicators
The following table describes the LED functionality for both front and
back indicators:
Front
Indicator State Description
Power On The AGS-1016 is switched on.
O AGS-1016 is switched o or not connected to AC
power. Check power connections and power switch
at on the rear of the unit.
Link/Act On Device connected to the port.
Flashing Port is receiving or transmitting data.
O No device connected to the port or the device is o.
Back
Indicator State Description
Speed/
Link/Act
Green Gigabit device connected to the port.
Amber 10/100Mbps device connected to the port.
Flashing Port is receiving or transmitting data.
O No device connected to the port or device is o.
SELECTING FRONT-PANEL LED COLOR
Use the switch on the rear panel of the AGS-1016 to select either blue or
green for the Power and System LEDs on the front panel to best match the
equipment in the rack where the Switch is sharing space.
AGS-1016 Selector Switch

Fold Fold Fold
3Connecting Devices
Use an Ethernet cable to connect the AGS-1016 to a device as shown below.
Luxul recommends at least Cat-5e unshielded twisted pair (CAT5e UTP)
cabling. To ensure best performance and stable data transmission at 1000
Mbps, use Category-6 unshielded twisted pair (CAT6 UTP).
The AGS-1016 automatically adjusts to the speed and duplex of the
connected device.
Connecting the AGS-1016 to a Device
When a device is properly connected and powered, the Link/Activity LED
for the device port lights up. Refer to the Hardware Operation section for
indicator definitions and troubleshooting.
4Connecting to a Router or Other Switch
Use an Ethernet cable to connect the AGS-1016 to a router or other switch as
shown below. The AGS-1016 automatically adjusts to the speed and duplex of
the connected switch or router, so uplink cables are not necessary.
Connecting the AGS-1016 to Router or Switch
When a router or switch is properly connected, the Link/Activity LED for each
port lights up. Refer to the Hardware Operation section for indicator definitions
and troubleshooting.
5Hardware Operation
The front panel of the AGS-1016 switch features one Power LED as well as a
Link/Activity LED for each port. The back panel of the switch includes (16)
10/100/1000 Mbps RJ-45 ports, a power connector, and a switch to select blue
or green front-panel LEDs. Each Ethernet port has one LED to indicate Link/
Activity as well as connection speed.
AGS-1016 Front Panel
Status Indicators
The following table describes the LED functionality for both front and
back indicators:
Front
Indicator State Description
Power On The AGS-1016 is switched on.
O AGS-1016 is switched o or not connected to AC
power. Check power connections and power switch
at on the rear of the unit.
Link/Act On Device connected to the port.
Flashing Port is receiving or transmitting data.
O No device connected to the port or the device is o.
Back
Indicator State Description
Speed/
Link/Act
Green Gigabit device connected to the port.
Amber 10/100Mbps device connected to the port.
Flashing Port is receiving or transmitting data.
O No device connected to the port or device is o.
SELECTING FRONT-PANEL LED COLOR
Use the switch on the rear panel of the AGS-1016 to select either blue or
green for the Power and System LEDs on the front panel to best match the
equipment in the rack where the Switch is sharing space.
AGS-1016 Selector Switch

Fold Fold Fold
3Connecting Devices
Use an Ethernet cable to connect the AGS-1016 to a device as shown below.
Luxul recommends at least Cat-5e unshielded twisted pair (CAT5e UTP)
cabling. To ensure best performance and stable data transmission at 1000
Mbps, use Category-6 unshielded twisted pair (CAT6 UTP).
The AGS-1016 automatically adjusts to the speed and duplex of the
connected device.
Connecting the AGS-1016 to a Device
When a device is properly connected and powered, the Link/Activity LED
for the device port lights up. Refer to the Hardware Operation section for
indicator definitions and troubleshooting.
4Connecting to a Router or Other Switch
Use an Ethernet cable to connect the AGS-1016 to a router or other switch as
shown below. The AGS-1016 automatically adjusts to the speed and duplex of
the connected switch or router, so uplink cables are not necessary.
Connecting the AGS-1016 to Router or Switch
When a router or switch is properly connected, the Link/Activity LED for each
port lights up. Refer to the Hardware Operation section for indicator definitions
and troubleshooting.
5Hardware Operation
The front panel of the AGS-1016 switch features one Power LED as well as a
Link/Activity LED for each port. The back panel of the switch includes (16)
10/100/1000 Mbps RJ-45 ports, a power connector, and a switch to select blue
or green front-panel LEDs. Each Ethernet port has one LED to indicate Link/
Activity as well as connection speed.
AGS-1016 Front Panel
Status Indicators
The following table describes the LED functionality for both front and
back indicators:
Front
Indicator State Description
Power On The AGS-1016 is switched on.
O AGS-1016 is switched o or not connected to AC
power. Check power connections and power switch
at on the rear of the unit.
Link/Act On Device connected to the port.
Flashing Port is receiving or transmitting data.
O No device connected to the port or the device is o.
Back
Indicator State Description
Speed/
Link/Act
Green Gigabit device connected to the port.
Amber 10/100Mbps device connected to the port.
Flashing Port is receiving or transmitting data.
O No device connected to the port or device is o.
SELECTING FRONT-PANEL LED COLOR
Use the switch on the rear panel of the AGS-1016 to select either blue or
green for the Power and System LEDs on the front panel to best match the
equipment in the rack where the Switch is sharing space.
AGS-1016 Selector Switch

Fold Fold Fold
READ ME FIRST
QUICK INSTALL GUIDE
16-Port Gigabit Switch
AGS-1016
Includes:
16-Port Gigabit Switch
Rack Mount Kit
Rubber Feet
Power Cord
SETUP AND CONFIGURATION
1Physical Installation
The AGS-1016 can be rack-mounted or used as a desktop switch. Install the
AGS-1016 in a stable/safe place to avoid any possible damage. Avoid placement
in direct sunlight. Do not place heavy articles on the AGS-1016 and verify the
ground connection of the outlet is functioning properly.
Desktop/Shelf Installation
For desktop/shelf installation, attach the four rubber feet to the corner inden-
tations on the bottom of the AGS-1016, then place the switch horizontally on
a solid, level platform.
Rack Installation
Use the included L brackets for convenient installation in a 19-inch server or
audio/video rack. Use four screws to attach the L-shaped brackets on both
sides of the AGS-1016 as shown below, then install the switch horizontally in the
rack. Use your desired hardware to ax the switch brackets to the rack.
Attach Feet for Desktop Installation Install Brackets for Rack-Mounting
2Connecting Ethernet and Power
Ethernet and Power Connections
Use any RJ-45 to connect the AGS-1016 to an Ethernet-enabled device,
including servers, routers or other switches. No crossover cable is necessary.
The AGS-1016 supports 10/100/1000 Mbps Ethernet; 10/100 Mbps half/
full-duplex mode and 1000 Mbps full-duplex mode.
Use the included power cable to connect the AGS-1016 to a surge protected
outlet. The AC input socket and a power switch are on the rear panel. The
built-in power supply supports 100~240VAC at 50/60Hz.
cCAUTION: Use only the correct power cord for your environment.
Any voltage other than standard 100/240 will result in
damage to the AGS-1016.
Sales
P: 801-822-5450
E: [email protected]
Technical Support
P: 801-822-5450 Option 3
E: [email protected]
LUX-QIG-AGS-1016-v4 06271701
Copyright and Trademark Notices
No part of this document may be modified or adapted in any way, for any purposes without permission
in writing from Luxul. The material in this document is subject to change without notice. Luxul reserves
the right to make changes to any product to improve reliability, function, or design. No license is
granted, either expressly or by implication or otherwise under any Luxul intellectual property rights. An
implied license only exists for equipment, circuits and subsystems contained in this or any Luxul product.
© Copyright 2017 Luxul. All rights reserved. The name Luxul, the Luxul logo, the Luxul logo mark and
Simply Connected are all trademarks and or registered trademarks of Luxul Wireless, Inc. All other
trademarks and registered trademarks are property of their respective holders.