Luxul XMS-1010P User manual

Simply Connected
Quick Install Guide
XMS-1010P
10-Port/8 PoE+ Gigabit Managed Switch
Use the XMS-1010P to:
fConnect up to 8 IP Cameras or Other
PoE-Enabled Devices
fAdd PoE/PoE+ Capability to Your Network
fOptimize Your Network with VLAN,QoS
and Network Security Features
fSimply Plug and Play

Quick Install Guide
XMS-1010P
a: 14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450
LUX-QIG-XMS-1010P 054151127
2
Quick Install Guide
Model Number: XMS-1010P
10-Port/8 PoE+ Gigabit Managed Switch
© 2015 Luxul. All Rights Reserved.
No part of this publication may be modified or adapted in any way, for any purposes
without permission in writing from Luxul. The material in this manual is subject to change
without notice. Luxul reserves the right to make changes to any product to improve reliability,
function, or design. No license is granted, either expressly or by implication or otherwise
under any Luxul intellectual property rights. An implied license only exists for equipment,
circuits and subsystems contained in this or any Luxul product.
DOCUMENT CONVENTIONS
The following graphical alerts are used in this document to indicate notable situations:
NOTE: Tips, hints, or special requirements that you should take note of.
CAUTION: Care is required. Disregarding a caution can result in data
loss or equipment malfunction.
WARNING!: Indicates a condition or procedure that could result in
personal injury or equipment damage.
FCC COMPLIANCE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
CONTACT LUXUL
Sales
P: 801-822-5450
E: [email protected]
Technical Support
P: 801-822-5450
E: suppor[email protected]om

Simply Connected
© 2015 Luxul. All Rights Reserved.
Other trademarks and registered trademarks are the property of their respective owners 3
PACKAGE CONTENTS
fXMS-1010P 10-Port/8 PoE+ Gigabit Managed Switch
fPower cable
fTwo L-shape brackets and eight matched screws
fFour rubber footpads
fQuick Install Guide
If any of the listed items are missing or damaged, please contact the reseller from whom you
purchased for return/replacement.
HARDWARE DESCRIPTION
Front Panel
The front panel of the XMS-1010P switch includes 8 1000Mbps RJ45 and Two Gigabit uplink
ports and LED indicators on the left side. Each 1000Mbps PoE port has one Link/Activity LED,
one 1000Mbps LED and one PoE LED, there are also two uplink LEDs, one Power LED, one
System LED and a reset button.
XMS-1010P Front Panel
Status indicators
Each port has one Link/Activity LED, one 1000Mbps LED and one PoE LED. In addition, there
are two SFP LEDs, one Power LED, one System LED, as well as a Reset button to reboot the
device or restore factory default settings. The green LED indicators show the working status
of the switch. The following table describes the LED functionality:

Quick Install Guide
XMS-1010P
a: 14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450
LUX-QIG-XMS-1010P 054151127
4
Indicator Name Description
POWER On Indicates that there is power to the XMS-1010P
Off If LED is off, check power connections and on/off
switch at the back of the unit.
Link/Act On There is a device connected to the port.
Flashing A port is receiving or transmitting data.
Off There is nothing connected to the port.
1000 Mbps On A device capable of 1000Mbps is connected to the port.
Off If a port has no device connected or it is not a 1000
Mbps capable device, the 1000 Mbps LED will be off.
PoE On A PoE enabled device is connected and being supplied
power
Off No PoE enabled device is connected or PoE is not
enabled on this port
SYSTEM On Indicates that the XMS-1010P is booting.
Flashing The XMS-1010P is running normally.
Off The XMS-1010P is in startup and initialization process
or is not on.
At startup, port LEDs will flash for 1 second as a self test.
Reset Button
The Reset button (Located at the lower left corner of the front panel) is used to clear the
current settings of the switch and restore factory default settings.
How to Use the Reset Button
fTo Hard Reset the Switch: With the XMS-1010P powered on, press the Reset button.
CAUTION: DO NOT hold the button as this will factory default
the switch
fTo Restore the Default Settings: With the XMS-1010P powered on, press and hold the Reset
button until the status of the System LED shows the following: On – flashing – off. You can now
release the Reset button, and the switch automatically restores the factory default settings.
When the System LED start flashing again, the XMS-1010P will be set to factory defaults.
CAUTION: Please note this will remove any configuration done to the switch
prior to Reset.

Simply Connected
© 2015 Luxul. All Rights Reserved.
Other trademarks and registered trademarks are the property of their respective owners 5
Network Ports
fThere are 8 10/100/1000Mbps RJ-45 ports (Ports 1~8).
fTwo Gigabit ports (that support Auto MDI/MDIX).
NOTE:
When powering up, the port LEDs corresponding to the optical
interface may take a moment to initialize. This is normal as the
XMS-1010P does not detect the optical connection until after the
initialization and startup of internal software systems are completed.
NOTE: The XMS-1010P has an internal 130W power supply. For optimal
switch performance, it is recommended that maximum combined
power usage of external PoE devices does not exceed 115W.
Rear Panel
The rear panel provides an AC input socket and power on/off switch. Use the included
power cable to connect the XMS-1010P to a surge protected outlet. The built-in high-
performance switching power supply of the XMS-1010P supports an input range of: AC 100 ~
240V, 50/60Hz 1.7A.
INSTALLATION PREPARATION
System and Environmental Requirements
fNetwork cables to connect the XMS-1010P to Ethernet enabled devices
fA computer supporting TCP/IP and equipped with a Web browser. Supported Web browser
versions include Microsoft IE 9.0 and up, Safari 5.0 and up or Mozilla Firefox 3.6 and up, Chrome
6.0, Opera 10.6 and up. The Web browser is used to configure the XMS-1010P.
fPower must be AC 100 ~ 240V, 50/60Hz 1.7A.
fTemperature of the operating environment should be: 32F~113F (0C~45C). Place the switch away
from heat generating devices. For best performance and heat dissipation/ventilation, make sure
there is adequate space around the switch.
fHumidity of the operating environment should be: 5%-95% non-condensing. Do not place the
switch in an extremely dirty or damp location.
fKeep the switch away from strong electromagnetic fields (i.e. Air Conditioner compressors, fluores-
cent light ballasts, CRT monitors/televisions, etc.), and free from vibration, dust and direct sun light.

Quick Install Guide
XMS-1010P
a: 14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450
LUX-QIG-XMS-1010P 054151127
6
3.2 Before Connecting to the Network
fThe XMS-1010P can be rack-mounted or used as a desktop switch. Before connecting to the
network, please be aware of the following requirements:
fInstall the XMS-1010P in a stable/safe place to avoid any possible damage
fMake sure there is adequate space around the XMS-1010P for adequate ventilation and proper
heat dissipation. It is recommended to have at least 4-6 inches around all sides.
fDo not place heavy articles on the XMS-1010P.
fPower outlets should be within 5 feet of the XMS-1010P.
fVerify the ground connection of the outlet is functioning properly.
fCheck the power cord to confi rm a secure connection.
fAvoid placement in direct sunlight.
fWhen installing the XMS-1010P on a fl at surface, attach the rubber feet to the bottom of the
device to avoid scratching the surface.
XMS-1010P INSTALLATION
Installation on Desktop/Shelf
As shown below, attach the four rubber footpads to 4 corner indentations on the bottom of
the XMS-1010P. Place the switch horizontally on a solid, level platform.
Desktop/Shelf Installation of XMS-1010P
Installation in a Rack
The XMS-1010P is suitable for 19-inch rack installation. With the included L brackets, it can be
conveniently installed into a server or audio rack. As shown below, use four screws to attach
the L-shaped brackets on either sides of the XMS-1010P, and horizontally insert the switch
into a free space within the rack. Use your desired hardware to affi x the switch supports to
the rack.
L-Shaped Supports for XMS-1010P

Simply Connected
© 2015 Luxul. All Rights Reserved.
Other trademarks and registered trademarks are the property of their respective owners 7
Network Connections
The XMS-1010P supports 10/100/1000 Mbps Ethernet; 10/100 Mbps half/full-duplex mode
and 1000 Mbps full-duplex mode. All RJ-45 ports support Auto MDI/MDIX and can be used
as ordinary ports or as Uplink ports. Any RJ-45 port can be used to connect the XMS-1010P
to an Ethernet enabled device (including servers, routers, and other switches) without a
crossover cable.
The XMS-1010P offers 2 Gigabit uplink ports.
Network Transmission Media
For the RJ-45 ports, Category-5, super Category-5 or Category-6 unshielded twisted
pair (CAT5/CAT5e/CAT6 UTP) should be used. For best results, it is recommended that
Category-6 shielded twisted pair be used to ensure stable data transmission at 1000 Mbps.
Optical fiber/cable should be selected based on the wavelength of the SFP optical module
to be used.
CAUTION: Make sure only one Uplink channel exists between switches or
between the XMS-1010P and a router. Otherwise, loops can occur
and result in network failure.
CONFIGURATION
Login
The XMS-1010P is not equipped with internal DHCP server. However, if you are connect-
ing to a Luxul Router with the default LAN address, the configuration will be automatic.
Otherwise, the IP address of the computer for login and configuration will need to be manu-
ally configured. The table below lists the default parameters of the XMS-1010P.
Parameter: Default Value
Default IP address: 192.168.0.3
Default user name: admin
Default password: admin
Login to the switch with the following steps:
1. Plug an Ethernet cable into any of the switch ports
2. Plug the other end into the Ethernet port of your computer
3. Power on the switch.
4. Check to see that the IP address of the computer is within this network segment: 192.168.0.xxx
(“xxx” ranges 2~254. For example, 192.168.0.50). For IP address settings, refer to Appendix 2.
5. Open the Web browser and enter 192.168.0.3.

Information on this document supersedes all previous versions. Products and documents
subject to change without notice. Products may be discontinued without notice.
LUX-QIG-XMS-1010P
054151127
a: 14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685
luxul.com | 801-822-5450
6. Enter the user name and password (default user name and default password are both set as
“admin”), and then click “OK” to login to the switch configuration window.
Click any menu item on the left to view and/or modify the corresponding settings or functions.
ADVANCED SETTINGS
For login and advanced settings information see the User Guide on luxul.com
FCC Statement:
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
This device complies with part 15 of the FCC Rules.
Hereby, Luxul, 14203 Minuteman Drive, Suite 201, Draper, Utah, 84020, declares that
this Luxul XMS-1010P is in compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC.
For a copy of this report send a self addressed stamped envelope to:
Luxul CE, 14203 Minuteman Drive, Suite 201, Draper, Utah, 84020.
Industry Canada
CAN ICES-3(A)/NMB-3(A)