Fold Fold Fold
3Preparing for Access
IP Addressing
If the XMS-2624P is connected to a network with a 192.168.0.X address
scheme, and your computer shares a similar address on the same network,
you can skip to the next step, Access and Setup.
nNote: If another device on your network shares the 192.168.0.4
address, you’ll need to temporarily reassign or remove that
device while you configure the XMS-2624P.
If your network uses an address scheme other than 192.168.0.X, you’ll need
to set a temporary static IP address on the computer you’re using for
configuration. To do so, set the IP address of your computer to an address
in the 192.168.0.X range, then set the Gateway/Router address to 192.168.0.4
(the default IP address of the XMS-2624P).
Once you’re finished configuring the switch, you can return your computer’s
IP configuration to normal, typically “Obtain Automatically/DHCP.”
nNote: Visit http://luxul.com/ip-addressing to learn more about
changing your computer’s IP address and getting connected.
4Access and Setup
Getting Connected
Use an Ethernet cable to connect your computer to the XMS-2624P, then
power on the switch.
Logging In
To access the XMS-2624P web configuration, open your web browser and
enter the switch’s default 192.168.0.4 IP address in the address field. Log in to
the switch using the default user name and password:
Default IP: 192.168.0.4
Username: admin
Password: admin
Select the menu items on the left to view and/or modify the configuration.
Refer to the Quick Setup Guide at Luxul.com for more detailed information on
setup, IP configuration and routing, PoE, VLANs, Spanning Tree, and Stacking.
5Hardware Operation
Front Panel
The front panel of the XMS-2624P includes 26 Gigabit Ethernet RJ-45 ports, two
Gigabit SFP+ ports, status-, link- and PoE LEDs, a Mode/Reset button and an
RJ-45 Console port.
XMS-2624P Front Panel View
Rear Panel
The Rear Panel of the XMS-2624P features a standard AC power input along with
a power switch.
LED Indicators
The LED indicators on the XMS-2624P include System, Link/Act and PoE LEDs,
and an LED for each port. These LED indicators show the operating status of
the XMS-2624P and each port connection.
Mode/Reset Button to Change LED Functionality
Tapping the Mode/Reset button briefly switches the port indicator between
displaying port link speed and PoE status.
The following chart shows the LED indicators of the XMS-2624P along with an
explanation of the indicator’s properties:
Indicator
Name
Description
System Green Flashing Indicates normal operation.
Green On Indicates a malfunction. Contact support.
Red On Indicates power-on system initialization.
O Indicates startup/initialization process or
that power is not on.
Port Link/
Act Status
1-26
Green 1000Mbps device connected to the port.
Yellow 10/100Mbps device connected to the port.
Flashing Port receiving or transmitting data.
O Nothing connected to the port.
Port PoE
Status 1-24
Green Switch is providing PoE power to a device.
Yellow PoE is o due to a fault or because the
connected device is exceeding power limit.
O Port disconnected or link failed.
Note: At startup, the port LEDs will flash briefly during a self-test.
Mode/Reset Button to Reset/Restore
The Reset button (located at the lower-left corner of the front panel) is
used to reset (reboot) the switch, or to restore the switch to factory
default settings.
XTo Reboot/Reset the Switch: With the XMS-2624P powered on, press
the Reset button for approximately three seconds until the Link/Act and
PoE LEDs both light, then release the button.
cCAUTION: Do not hold the button for more than four seconds.
Doing so could erase all settings and restore
factory defaults.
XTo Restore Default Settings: With the XMS-2624P powered on, press
and hold the Reset button approximately eight seconds, until both the
Link/Act and PoE LEDs turn o, then release the Reset button and the
switch automatically restores factory default settings and reboots. Once
the System LED starts flashing again, the XMS-2624P is running with
factory defaults.
cCAUTION: Please note that restoring Default Settings will remove
any/all custom configuration.
