Luxul Xen XGS-1008 User manual

READ ME FIRST
Fold Fold Fold
QUICK INSTALL GUIDE
8-Port Gigabit Desktop Switch
XGS-1008
Includes:
One: XGS-1008 8-Port Gigabit Desktop Switch
One: Power Adapter
INSTALLATION AND SETUP
1Physical Installation
Install the XGS-1008 in a stable/safe place to avoid any possible damage. Avoid
placement in direct sunlight and do not place heavy articles on the XGS-1008.
Ensure there is adequate space for proper heat dissipation and ventilation
around the switch.
XGS-1008 Front Panel and Side View Showing Ventilation
2Connecting Power
Connect the included AC power adapter to a power outlet near the XGS-1008,
then connect the power adapter plug to the switch power connector.
XGS-1008 Rear Panel Detail with DC Power Connector
cCAUTION: Use only the included power supply. If a different power
supply is used, it could damage the XGS-1008.
LEGAL AND REGULATORY INFORMATION
© 2016 Luxul. All Rights Reserved.
No part of this publication, or any other publication may be modified or adapt-
ed in any way, for any purposes without permission in writing from Luxul. The
material in this manual is subject to change without notice. Luxul reserves the
right to make changes to any product to improve reliability, function, or design.
No license is granted, either expressly or by implication or otherwise under any
Luxul intellectual property rights. An implied license only exists for equipment,
circuits and subsystems contained in this or any Luxul product.
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interfer-
ence that may cause undesired operation.
FCC Statement—Wireless FCC 2.4GHz & 5GHz 802.11abgn
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules.
Hereby, Luxul, 14203 Minuteman Drive, Suite 201, Draper, Utah,
84020, declares that this Luxul XGS-1008 is in compliance with the
essential requirements and other relevant provisions of Directive
1995/5/EC.
For a copy of this report send a self addressed stamped envelope
to: Luxul CE, 14203 Minuteman Drive, Suite 201, Draper, Utah, 84020.
Industry Canada (RSS-Gen Issue 4)
CAN ICES-3(B)/NMB-3(B)
Sales
P: 801-822-5450
E: s[email protected]
Technical Support
P: 801-822-5450 Option 3
E: suppor[email protected]
© 2016 Luxul. All Rights Reserved. LUX-QIG-XGS-1008 0161609

READ ME FIRST
Fold Fold Fold
QUICK INSTALL GUIDE
8-Port Gigabit Desktop Switch
XGS-1008
Includes:
One: XGS-1008 8-Port Gigabit Desktop Switch
One: Power Adapter
INSTALLATION AND SETUP
1Physical Installation
Install the XGS-1008 in a stable/safe place to avoid any possible damage. Avoid
placement in direct sunlight and do not place heavy articles on the XGS-1008.
Ensure there is adequate space for proper heat dissipation and ventilation
around the switch.
XGS-1008 Front Panel and Side View Showing Ventilation
2Connecting Power
Connect the included AC power adapter to a power outlet near the XGS-1008,
then connect the power adapter plug to the switch power connector.
XGS-1008 Rear Panel Detail with DC Power Connector
cCAUTION: Use only the included power supply. If a different power
supply is used, it could damage the XGS-1008.
LEGAL AND REGULATORY INFORMATION
© 2016 Luxul. All Rights Reserved.
No part of this publication, or any other publication may be modified or adapt-
ed in any way, for any purposes without permission in writing from Luxul. The
material in this manual is subject to change without notice. Luxul reserves the
right to make changes to any product to improve reliability, function, or design.
No license is granted, either expressly or by implication or otherwise under any
Luxul intellectual property rights. An implied license only exists for equipment,
circuits and subsystems contained in this or any Luxul product.
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interfer-
ence that may cause undesired operation.
FCC Statement—Wireless FCC 2.4GHz & 5GHz 802.11abgn
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules.
Hereby, Luxul, 14203 Minuteman Drive, Suite 201, Draper, Utah,
84020, declares that this Luxul XGS-1008 is in compliance with the
essential requirements and other relevant provisions of Directive
1995/5/EC.
For a copy of this report send a self addressed stamped envelope
to: Luxul CE, 14203 Minuteman Drive, Suite 201, Draper, Utah, 84020.
Industry Canada (RSS-Gen Issue 4)
CAN ICES-3(B)/NMB-3(B)
Sales
P: 801-822-5450
E: s[email protected]
Technical Support
P: 801-822-5450 Option 3
E: suppor[email protected]
© 2016 Luxul. All Rights Reserved. LUX-QIG-XGS-1008 0161609

READ ME FIRST
Fold Fold Fold
QUICK INSTALL GUIDE
8-Port Gigabit Desktop Switch
XGS-1008
Includes:
One: XGS-1008 8-Port Gigabit Desktop Switch
One: Power Adapter
INSTALLATION AND SETUP
1Physical Installation
Install the XGS-1008 in a stable/safe place to avoid any possible damage. Avoid
placement in direct sunlight and do not place heavy articles on the XGS-1008.
Ensure there is adequate space for proper heat dissipation and ventilation
around the switch.
XGS-1008 Front Panel and Side View Showing Ventilation
2Connecting Power
Connect the included AC power adapter to a power outlet near the XGS-1008,
then connect the power adapter plug to the switch power connector.
XGS-1008 Rear Panel Detail with DC Power Connector
cCAUTION: Use only the included power supply. If a different power
supply is used, it could damage the XGS-1008.
LEGAL AND REGULATORY INFORMATION
© 2016 Luxul. All Rights Reserved.
No part of this publication, or any other publication may be modified or adapt-
ed in any way, for any purposes without permission in writing from Luxul. The
material in this manual is subject to change without notice. Luxul reserves the
right to make changes to any product to improve reliability, function, or design.
No license is granted, either expressly or by implication or otherwise under any
Luxul intellectual property rights. An implied license only exists for equipment,
circuits and subsystems contained in this or any Luxul product.
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interfer-
ence that may cause undesired operation.
FCC Statement—Wireless FCC 2.4GHz & 5GHz 802.11abgn
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules.
Hereby, Luxul, 14203 Minuteman Drive, Suite 201, Draper, Utah,
84020, declares that this Luxul XGS-1008 is in compliance with the
essential requirements and other relevant provisions of Directive
1995/5/EC.
For a copy of this report send a self addressed stamped envelope
to: Luxul CE, 14203 Minuteman Drive, Suite 201, Draper, Utah, 84020.
Industry Canada (RSS-Gen Issue 4)
CAN ICES-3(B)/NMB-3(B)
Sales
P: 801-822-5450
E: s[email protected]
Technical Support
P: 801-822-5450 Option 3
E: suppor[email protected]
© 2016 Luxul. All Rights Reserved. LUX-QIG-XGS-1008 0161609

Fold Fold Fold
3Connecting Ethernet
Connecting Devices
Use standard Ethernet cable to connect the XGS-1008 to Ethernet devices
as shown below. Luxul recommends Category-5, super Category-5
or Category-6 unshielded twisted pair (CAT5/CAT5e/CAT6 UTP). To
ensure best performance and stable data transmission at 1000 Mbps, use
Category-6 shielded twisted pair.
Connecting the XGS-1008 to a Device
When a device is properly connected, the Link/Activity LEDs for each port
lights up green/orange. Please refer to the section on LED Indicators for
definitions and troubleshooting.
Connecting to a Router or Other Switch
For best performance, and to maximize available ports, Luxul recommends
connecting LAN devices to the XGS-1008, then connecting the switch to a
router LAN port or another switch as shown in the illustration.
Internet
Connecting the XGS-1008 to a Router or Switch
When devices are properly connected, the Link/Activity LEDs for each port
light up green/orange. Refer to the section on LED Indicators for definitions
and troubleshooting.
4Hardware Description
Front Panel
The front panel of the XGS-1008 includes eight Link/Activity LEDs and one
power LED. For more information on these LEDs, refer to the table describing
these indicators in the next section.
XGS-1008 Front Panel View
XGS-1008 Rear Panel View
5LED Indicators
The LED indicators of the XGS-1008 include one Power indicator and 8 Link/
Activity indicators. These LED indicators show the operating status of the
XGS-1008 and each switch connection.
The following chart shows the LED indicators of the XGS-1008 along with a
description of each indicator:
LED Color Status Description
Power Green On The XGS-1008 is powered.
Off The XGS-1008 is unpowered. Check
the DC power supply to ensure proper
connection to the outlet and switch.
Link/
Activity
Green On The XGS-1008 is connected at
1000Mbps.
Blinking The XGS-1008 is transmitting/receiving
data packets at 1000Mbps.
Orange On The XGS-1008 is connected at
10/100Mbps.
Blinking The XGS-1008 is transmitting/receiving
data packets at 10/100Mbps.
Off Indicates the port is not connected to
a device.

Fold Fold Fold
3Connecting Ethernet
Connecting Devices
Use standard Ethernet cable to connect the XGS-1008 to Ethernet devices
as shown below. Luxul recommends Category-5, super Category-5
or Category-6 unshielded twisted pair (CAT5/CAT5e/CAT6 UTP). To
ensure best performance and stable data transmission at 1000 Mbps, use
Category-6 shielded twisted pair.
Connecting the XGS-1008 to a Device
When a device is properly connected, the Link/Activity LEDs for each port
lights up green/orange. Please refer to the section on LED Indicators for
definitions and troubleshooting.
Connecting to a Router or Other Switch
For best performance, and to maximize available ports, Luxul recommends
connecting LAN devices to the XGS-1008, then connecting the switch to a
router LAN port or another switch as shown in the illustration.
Internet
Connecting the XGS-1008 to a Router or Switch
When devices are properly connected, the Link/Activity LEDs for each port
light up green/orange. Refer to the section on LED Indicators for definitions
and troubleshooting.
4Hardware Description
Front Panel
The front panel of the XGS-1008 includes eight Link/Activity LEDs and one
power LED. For more information on these LEDs, refer to the table describing
these indicators in the next section.
XGS-1008 Front Panel View
XGS-1008 Rear Panel View
5LED Indicators
The LED indicators of the XGS-1008 include one Power indicator and 8 Link/
Activity indicators. These LED indicators show the operating status of the
XGS-1008 and each switch connection.
The following chart shows the LED indicators of the XGS-1008 along with a
description of each indicator:
LED Color Status Description
Power Green On The XGS-1008 is powered.
Off The XGS-1008 is unpowered. Check
the DC power supply to ensure proper
connection to the outlet and switch.
Link/
Activity
Green On The XGS-1008 is connected at
1000Mbps.
Blinking The XGS-1008 is transmitting/receiving
data packets at 1000Mbps.
Orange On The XGS-1008 is connected at
10/100Mbps.
Blinking The XGS-1008 is transmitting/receiving
data packets at 10/100Mbps.
Off Indicates the port is not connected to
a device.

Fold Fold Fold
3Connecting Ethernet
Connecting Devices
Use standard Ethernet cable to connect the XGS-1008 to Ethernet devices
as shown below. Luxul recommends Category-5, super Category-5
or Category-6 unshielded twisted pair (CAT5/CAT5e/CAT6 UTP). To
ensure best performance and stable data transmission at 1000 Mbps, use
Category-6 shielded twisted pair.
Connecting the XGS-1008 to a Device
When a device is properly connected, the Link/Activity LEDs for each port
lights up green/orange. Please refer to the section on LED Indicators for
definitions and troubleshooting.
Connecting to a Router or Other Switch
For best performance, and to maximize available ports, Luxul recommends
connecting LAN devices to the XGS-1008, then connecting the switch to a
router LAN port or another switch as shown in the illustration.
Internet
Connecting the XGS-1008 to a Router or Switch
When devices are properly connected, the Link/Activity LEDs for each port
light up green/orange. Refer to the section on LED Indicators for definitions
and troubleshooting.
4Hardware Description
Front Panel
The front panel of the XGS-1008 includes eight Link/Activity LEDs and one
power LED. For more information on these LEDs, refer to the table describing
these indicators in the next section.
XGS-1008 Front Panel View
XGS-1008 Rear Panel View
5LED Indicators
The LED indicators of the XGS-1008 include one Power indicator and 8 Link/
Activity indicators. These LED indicators show the operating status of the
XGS-1008 and each switch connection.
The following chart shows the LED indicators of the XGS-1008 along with a
description of each indicator:
LED Color Status Description
Power Green On The XGS-1008 is powered.
Off The XGS-1008 is unpowered. Check
the DC power supply to ensure proper
connection to the outlet and switch.
Link/
Activity
Green On The XGS-1008 is connected at
1000Mbps.
Blinking The XGS-1008 is transmitting/receiving
data packets at 1000Mbps.
Orange On The XGS-1008 is connected at
10/100Mbps.
Blinking The XGS-1008 is transmitting/receiving
data packets at 10/100Mbps.
Off Indicates the port is not connected to
a device.

Fold Fold Fold
3Connecting Ethernet
Connecting Devices
Use standard Ethernet cable to connect the XGS-1008 to Ethernet devices
as shown below. Luxul recommends Category-5, super Category-5
or Category-6 unshielded twisted pair (CAT5/CAT5e/CAT6 UTP). To
ensure best performance and stable data transmission at 1000 Mbps, use
Category-6 shielded twisted pair.
Connecting the XGS-1008 to a Device
When a device is properly connected, the Link/Activity LEDs for each port
lights up green/orange. Please refer to the section on LED Indicators for
definitions and troubleshooting.
Connecting to a Router or Other Switch
For best performance, and to maximize available ports, Luxul recommends
connecting LAN devices to the XGS-1008, then connecting the switch to a
router LAN port or another switch as shown in the illustration.
Internet
Connecting the XGS-1008 to a Router or Switch
When devices are properly connected, the Link/Activity LEDs for each port
light up green/orange. Refer to the section on LED Indicators for definitions
and troubleshooting.
4Hardware Description
Front Panel
The front panel of the XGS-1008 includes eight Link/Activity LEDs and one
power LED. For more information on these LEDs, refer to the table describing
these indicators in the next section.
XGS-1008 Front Panel View
XGS-1008 Rear Panel View
5LED Indicators
The LED indicators of the XGS-1008 include one Power indicator and 8 Link/
Activity indicators. These LED indicators show the operating status of the
XGS-1008 and each switch connection.
The following chart shows the LED indicators of the XGS-1008 along with a
description of each indicator:
LED Color Status Description
Power Green On The XGS-1008 is powered.
Off The XGS-1008 is unpowered. Check
the DC power supply to ensure proper
connection to the outlet and switch.
Link/
Activity
Green On The XGS-1008 is connected at
1000Mbps.
Blinking The XGS-1008 is transmitting/receiving
data packets at 1000Mbps.
Orange On The XGS-1008 is connected at
10/100Mbps.
Blinking The XGS-1008 is transmitting/receiving
data packets at 10/100Mbps.
Off Indicates the port is not connected to
a device.

READ ME FIRST
Fold Fold Fold
QUICK INSTALL GUIDE
8-Port Gigabit Desktop Switch
XGS-1008
Includes:
One: XGS-1008 8-Port Gigabit Desktop Switch
One: Power Adapter
INSTALLATION AND SETUP
1Physical Installation
Install the XGS-1008 in a stable/safe place to avoid any possible damage. Avoid
placement in direct sunlight and do not place heavy articles on the XGS-1008.
Ensure there is adequate space for proper heat dissipation and ventilation
around the switch.
XGS-1008 Front Panel and Side View Showing Ventilation
2Connecting Power
Connect the included AC power adapter to a power outlet near the XGS-1008,
then connect the power adapter plug to the switch power connector.
XGS-1008 Rear Panel Detail with DC Power Connector
cCAUTION: Use only the included power supply. If a different power
supply is used, it could damage the XGS-1008.
LEGAL AND REGULATORY INFORMATION
© 2016 Luxul. All Rights Reserved.
No part of this publication, or any other publication may be modified or adapt-
ed in any way, for any purposes without permission in writing from Luxul. The
material in this manual is subject to change without notice. Luxul reserves the
right to make changes to any product to improve reliability, function, or design.
No license is granted, either expressly or by implication or otherwise under any
Luxul intellectual property rights. An implied license only exists for equipment,
circuits and subsystems contained in this or any Luxul product.
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interfer-
ence that may cause undesired operation.
FCC Statement—Wireless FCC 2.4GHz & 5GHz 802.11abgn
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules.
Hereby, Luxul, 14203 Minuteman Drive, Suite 201, Draper, Utah,
84020, declares that this Luxul XGS-1008 is in compliance with the
essential requirements and other relevant provisions of Directive
1995/5/EC.
For a copy of this report send a self addressed stamped envelope
to: Luxul CE, 14203 Minuteman Drive, Suite 201, Draper, Utah, 84020.
Industry Canada (RSS-Gen Issue 4)
CAN ICES-3(B)/NMB-3(B)
Sales
P: 801-822-5450
E: s[email protected]
Technical Support
P: 801-822-5450 Option 3
E: suppor[email protected]
© 2016 Luxul. All Rights Reserved. LUX-QIG-XGS-1008 0161609