Luxul XFS-1084P User manual

READ ME FIRST
Fold Fold Fold
QUICK INSTALL GUIDE
8-Port PoE Switch
XFS-1084P
Includes:
One: XFS-1084P 8-Port PoE Switch
One: Power Adapter and Cord
INSTALLATION AND SETUP
1Physical Installation
Place the XFS-1084P horizontally on a solid, level surface in a stable/safe place
to avoid any possible damage. Avoid placement in direct sunlight, do not place
heavy articles on the switch, and allow for proper ventilation.
XFS-1084P Front Panel and Side View Showing Ventilation
2Connecting Power
Use any RJ-45 to connect the XFS-1084P to an Ethernet-enabled device,
including servers, routers or other switches. No crossover cable is necessary.
Connect the power adapter plug to the switch power connector, then
connect the included AC power adapter to a power outlet.
cCAUTION: Use only the included AC power adapter, rated for
48VDC @ 1.25A. Using a dierent AC adapter could
damage the XFS-1084P.
XFS-1084P Rear Panel View
Sales
P: 801-822-5450
E: [email protected]
Technical Support
P: 801-822-5450 Option 3
E: [email protected]
LUX-QIG-XFS-1084P-v1 05161609
Copyright and Trademark Notices
No part of this document may be modified or adapted in any way, for any purposes without permission
in writing from Luxul. The material in this document is subject to change without notice. Luxul reserves
the right to make changes to any product to improve reliability, function, or design. No license is granted,
either expressly or by implication or otherwise under any Luxul intellectual property rights. An implied
license only exists for equipment, circuits and subsystems contained in this or any Luxul product.
© Copyright 2016 Luxul. All rights reserved. The name Luxul, the Luxul logo, the Luxul logo mark and
Simply Connected are all trademarks and or registered trademarks of Luxul Wireless, Inc. All other
trademarks and registered trademarks are property of their respective holders.

Fold Fold Fold
3Connecting Ethernet Devices
Connecting Devices
Use standard Ethernet CAT5, CAT5e or CAT6 cable to connect the XFS-
1084P to a device as described below. The XFS-1084P will automatically
adjust to the speed and duplex of the connected device.
The PoE function is autosensing. As long as the powered device is 802.3af
compliant, the switch will provide power. The XFS-1084P PoE power
budget is 57W total and a maximum of 15.4W per port.
nNOTE: The switch is not capable of powering legacy PoE devices or
802.3at devices that require more than 15.4 watts.
87654321
PoE
48V 1.25A
Connecting the XFS-1084P to a Device
When a device is properly connected, the Link/Activity LEDs for each
port lights up green. Please refer to the LED Indicators section for defini-
tions and troubleshooting.
Connecting to a Router or Other Switch
For best performance, and to maximize available ports, Luxul recommends
connecting LAN devices to the XFS-1084P, then connecting the switch to a
router LAN port or another switch as shown in the illustration.
Connecting the XFS-1084P to a Router and Devices
When a device is properly connected, the Link/Activity LEDs for each port lights
up green. Please refer to the following section on LED Indicators for definitions
and troubleshooting.
nNOTE: Ports 1-4 are PoE ports and should not be used for the uplink
connection.
4Hardware Operation
Front Panel
The front panel of the XFS-1084P includes eight Link/Activity LEDs, one power
LED, four PoE Status LEDs and one PoE Max LED. Refer to the detailed descrip-
tion of these indicators in the following section on LED Indicators.
XFS-1084P Front Panel View
Rear Panel Layout
The Rear Panel of the XFS-1084P includes eight 10/100Mbps RJ-45 Ethernet ports
and one DC power port used for DC power input.
XFS-1084P Rear Panel View
LED Indicators
The LED indicators on the XFS-1084P include eight Link/Activity LEDs,
one power LED, four PoE Status LEDs and one PoE Max LED. These
LED indicators show the operating status of the XFS-1084P and
each switch connection.
The following chart shows the LED indicators of the XFS-1084P along with
an explanation of the indicator’s properties:
LED Color Status Description
Power Green On The XFS-1084P is powered.
O Check the DC power supply to ensure
proper connection to the outlet and
the XFS-1084P.
PoE Max Red On Maximum output wattage reached.
Red Flashing Maximum output wattage exceeded.
O Maximum output wattage not reached.
PoE
Status
Green On Delivering PoE power to connected device.
Green Flashing Can indicate an Ethernet cable short or the
connected device is attempting to draw
more than 15.4W.
O No PoE power being delivered.
LINK/
ACT
Green On The XFS-1084P is connected.
Green Flashing The XFS-1084P is transmitting/receiving
data packets.
O The port is not connected to a device.