Luxul XAP-1020 User manual

luxul.com
Simply Connected
User Guide
XAP-1020
Luxul Xen™ Low Profile
802.11b/g/n Wireless Access Point
Use the XAP-1020 to:
Provide an Unobtrusive Wireless Network that Minimizes
Unsightly Cables or Equipment
Deliver “Whole Home” or Offi ce 802.11n Wi-Fi Coverage With a
Single Access Point
Increase Mobile Client Device Network Sensitivity and
Performance
Simplify Installation While Minimizing Setup Time and Expense
Eliminate Client Device Roaming Issues
AP
Use the XAP-1020 to:

User Guide
2© Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.
LUXUL XEN HIGH PERFORMANCE LOW PROFILE
802.11b/g/n Wireless Access Point
Model Number: XAP-1020
FCC ID: W59XAP101020
IC: 8584A-XAP101020
USER GUIDE
© 2011 Luxul. All Rights Reserved.
No part of this publication may be modifi ed or adapted in any way, for any
purposes without permission in writing from Luxul. The material in this manual
is subject to change without notice. Luxul reserves the right to make changes to
any product to improve reliability, function, or design. No license is granted, either
expressly or by implication or otherwise under any Luxul intellectual property rights.
An implied license only exists for equipment, circuits and subsystems contained in
this or any Luxul product.
This product is covered by one or more U.S. and foreign patents Patents: 7,379,717,
6,606,075, 6,373,448, other patents pending
DOCUMENT CONVENTIONS
The following graphical alerts are used in this document to indicate notable situations:
NOTE: Tips, hints, or special requirements that you should take note of.
CAUTION: Care is required. Disregarding a caution can result in data
loss or equipment malfunction.
WARNING!: Indicates a condition or procedure that could result in
personal injury or equipment damage.
FCC COMPLIANCE
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.

luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460
User Guide
3
luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460
33
CONTENTS
1 INTRODUCTION 4
1.1 Warnings 5
1.2 Site Preparation 5
2 XAP-1010 SPECIFICATIONS 5
3 GETTING STARTED 7
3.1 System Requirements 7
3.2 Package Contents 7
3.3 Safety Information 7
4 HARDWARE FEATURES AND INSTALLATION 8
4.1 Front View 8
4.2 Rear View 10
4.3 Environmental Requirements 11
4.4 Hardware Installation 12
5 CONFIGURATION 16
5.1 Login 16
5.2 Quick Setup 16
5.3 Wireless 20
5.4 Maintenance 23
5.5 QoS 25
5.6 Status 26
6 REGULATORY COMPLIANCE 27
6.1 Health and Safety Recommendations 27
6.2 RF Exposure Guidelines 28
6.3 Radio Frequency Interference Requirements—FCC 28
6.4 Radio Transmitters (Part 15) 29
6.5 Industry Canada (RSS-Gen Issue 2) 29
APPENDIX 1: TECHNICAL SUPPORT 29

User Guide
4© Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.
1 INTRODUCTION
Congratulations on your purchase of the Luxul Xen™ Low Profi le 802.11n Wireless
Access Point (XAP-1020). The XAP-1020 provides superior Wi-Fi coverage while
maintaining a discreet, elegant profi le for deployment in post-construction resi-
dential and commercial Wi-Fi installations. The XAP-1020 can be installed directly
on a wall or ceiling, or mounted to the included adjustable wall bracket that allows
the access point to be “aimed” for optimal coverage. Powered by Luxul’s Xen3D™
Technology, the XAP-1020 enhances data throughput and coverage by as much as
400% over traditional Wi-Fi gear, providing for whole home or small offi ce cover-
age with a single access point. With this high performance wireless access point,
computers and wireless devices that are compatible with 802.11b/g and/or 802.11n
can sustain maximum data rates and improved overall performance at signifi cantly
greater distances.
The XAP-1020 features Luxul’s XenSmart™ web based management interface.
XenSmart provides a powerful, yet simple method for setting up and optimizing
the wireless network. The XAP-1020 is also XenConnect™ enabled for optimal per-
formance and installation simplicity when deployed together with Luxul Routers,
Gigabit Switches, and other Luxul products.
XAP-1020 Features:
Implements Patented Xen3D™ Technology for Enhanced Throughput and
Coverage
Highest FCC Approved Performance (Effective EIRP 36dBm) for Farther Reaching
Signal and Maximum Data Rates
18dB of Receive Gain Increases Client Device Network Sensitivity and
Performance
Complies with 2.4 GHz IEEE 802.11n Standard. Backward Compatible with IEEE
802.11g/b
Supports WMM QoS Functionality to Prioritize Multimedia Traffi c
Enhanced Multi-Level Security with WPA-PSK (TKIP, AES, TKIP & AES), WPA2-PSK
(AES), WPA-PSK/WPA2-PSK Personal (TKIP & AES) and 128-bit WEP
Supports up to 8 SSIDs with Individual Security Settings
Multiple SSIDs Support VLAN Tagging (1 VLAN per SSID)
Single Cable Installation with PoE (supports both IEEE 802.3af and Legacy)
Firmware Upgradeable
Easy 3 Step Setup through Web-based XenSmart™ User Interface

luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460
User Guide
5
luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460
55
Installs Discreetly on Wall or Ceiling
XenConnect™ Enabled for Maximum Compatibility and Performance with Other
Luxul Xen Products
1.1 Warnings
Read all installation instructions and site survey reports, and verify correct equip-
ment installation before connecting the XAP-1020 to its power source.
Remove jewelry and watches before installing this equipment.
Verify that the unit is grounded before connecting it to the power source.
Verify that any device connected to this unit is properly wired and grounded.
Connect all power cords to a properly wired and grounded electrical circuit.
Verify that the electrical circuits have appropriate overload protection.
Attach only approved power cords to the device.
Verify that the power connector and socket are accessible at all times during the
operation of the equipment.
Do not work with power circuits in dimly lit spaces.
Do not install this equipment or work with its power circuits during thunder-
storms or other weather conditions that could cause a power surge.
Verify there is adequate ventilation around the device, and that ambient tem-
peratures meet equipment operation specifi cations.
Products outside the approved confi gurations may be in violation of Part 15 of
the FCC Rules.
1.2 Site Preparation
Consult your site survey and network analysis reports to determine specifi c
equipment placement, power drops, and so on.
Assign installation responsibility to the appropriate personnel.
Identify and document where all installed components are located.
Provide a suffi cient number of power drops for your equipment.
Ensure adequate, dust-free ventilation to all installed equipment.
Identify and prepare Ethernet and console port connections.
Verify that cable lengths are within the maximum allowable distances for optimal
and certifi ed signal transmission.

User Guide
6© Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.
2 XAP-1020 SPECIFICATIONS
Standards IEEE 802.11n
IEEE 802.11b/g
IEEE 802.3af
Hardware LAN Port: 1 RJ45 10/100 Mbps data and power input
 7dBi Circular Polarized Directional Antenna
System LEDs: Power, WLAN active, LAN link/activity,
Bridge mode active.
RF Information Frequency Band: 2.401 – 2.473GHz
Operating Channels: 11
Available Transmit Power 2.401 – 2.473GHz (IEEE802.11g/n):
Up to 36dBm EIRP
30dBm @ 6~9Mbps / MCS0
29dBm @ 12~18Mbps / MCS1-2
27dBm @ 24~36Mbps / MCS3-4
26dBm @ 48~54Mbps / MCS5-7
2.401 – 2.473GHz (IEEE802.11b):
Up to 36dBm EIRP
30dBm @ 1~11Mbps
Available Receive Gain  2.401 – 2.473GHz (IEEE802.11g/n):
Up to 18dBm
2.401 – 2.473GHz (IEEE802.11b):
Up to 18dBm
Receive Sensitivity (Typical) 2.401 – 2.473GHz (IEEE802.11n): Up to -91dBm
2.401 – 2.473GHz (IEEE802.11g): Up to -92dBm
2.401 – 2.473GHz (IEEE802.11b): Up to -93dBm
Wireless Operation Modes Access Point
Point-to Point Wireless Bridge
Point-to-Multipoint Wireless Bridge
Management and Security XenSmart™ Remote Web-based Management
WEP (128 bit)
WPA-PSK (TKIP, AES, TKIP&AES)
WPA2-PSK (AES)
WPA-PSK/WPA2-PSK Auto (TKIP&AES)
Web Based Firmware Upgrade
QoS: Wireless Multi-Media (WMM) Extensions
Certifi cations FCC Part 15, Class B
Power Requirements Ethernet POE in: 48VDC/0.375A for IEEE 802.3af
Compliance
Power Consumption: 5W Nominal, 13W Max

luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460
User Guide
7
luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460
77
Temperature Range Operating: 14°F to 131°F (-10°C to 55°C)
Storage: -40°F to 158°F (-40°C to 70°C)
Operating Humidity 5% to 95% (Non-condensing)
Mechanical Dimensions WxHxD: 5.5”(139.7mm) x 5.5”(139.7mm) x
1.5”(38.1mm)
Weight Item: .7 lbs
With Packaging: 1.5 lbs
3 GETTING STARTED
3.1 System Requirements
Devices Supporting 802.11b, 802.11g or 802.11n
Web Browser (Microsoft IE 7.0 and up, Mozilla Firefox 1.0 and up, Safari 1.0 and up,
Google Chrome 5.0 and up)
CAT5 Ethernet Cable
AC Power Socket (100 – 240 V, 50/60 Hz)
Internet Connection to View Documentation Online
3.2 Package Contents
XAP-1020 Wireless Access Point
POE Injector and Power Adapter
Wall Mounting Bracket and Hardware
Quick Install Guide
NOTE: If any of the listed items are missing or damaged, please contact
the reseller from whom you purchased for return/replacement.
3.3 Safety Information
To maintain the safety of users and property, follow these safety instructions:
The XAP-1020 wireless access point is designed for indoor use only. DO NOT
place this access point outdoors. If you require an outdoor access point, please
consider the Luxul XAP-1040.
DO NOT install this access point in or near hot or humid places, such as a kitchen
or bathroom. Take care to minimize exposure to excessive heat or moisture.
DO NOT pull any connected cable with force. When disconnecting cables, do so
by disconnecting fi rst from the access point. When reconnecting, connect the AP
fi rst and then the Power/data source.

User Guide
8© Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.
When installing the access point, be sure it is fi rmly secured to the wall or
mounting bracket.
Accessories of this access point, such as mounting screws, the POE injector and
power supply may be dangerous to small children under 3 years of age. KEEP All
ACCESSORIES OUT OF THE REACH OF CHILDREN!
The access point may become hot when in use for extended time periods. This is
normal and is not a malfunction. DO NOT install this access point where it will
be exposed to paper, cloth or other fl ammable materials. If not using the electri-
cal box included with the unit, ALWAYS use a properly shielded and UL listed
electrical box for installation.
The XAP-1020 contains no user-serviceable parts. If the access point is not
working properly, contact your dealer and ask for help. DO NOT attempt to
disassemble the access point.
4 HARDWARE FEATURES AND INSTALLATION
The XAP-1020 high powered access point is designed for optimal performance as
well as for simple and effi cient installation and setup. It implements Luxul’s circular
polarized directional antenna technology and is packaged for installation on a wall
or ceiling. Because the signal generated by the XAP-1020 is directional in nature, the
unit should be placed in a location that allows the antenna face to be “pointed”
towards the desired coverage area. Typically this would be on a top fl oor ceiling
pointed downwards in a multi-story installation; or for single level or two level
layouts, on a wall pointed towards the desired coverage.
4.1 Front View
For maximum discretion, the front of the XAP-1020 has no LED indicators. It
consists simply of the access point cover with the Luxul icon that indicates proper
top/bottom installation orientation of the access point.

luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460
User Guide
9
luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460
99
XAP-1020 Front View
4.2 Rear View
The rear of the XAP-1020 provides one RJ-45 connection that is used to deliver both
power and data to the access point. It also provides a reset button for restoring the
access point to factory default settings and multiple options for mounting the XAP-
1020 directly on a wall or ceiling or using the adjustable wall mount bracket.
XAP-1020 Rear View

User Guide
10 © Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.
XAP-1020 with Mount
4.3 Top View
The top left side of the XAP-1020 has a small viewing portal for validating System
LED functionality during setup and/or for diagnostic purposes. For discreet installa-
tion, all System LEDs are internal and can only be seen through this viewing portal.
DO NOT open the XAP-1020 to see System LEDs as the access point contains no
user serviceable parts and doing so will void your warranty.
XAP-1020 Top View