Luxul XAP-1030 User manual

luxul.com
Simply Connected
Simply ConnectedSimply Connected
Quick Install Guide
XAP-1030
Luxul Commercial Grade Omni
802.11b/g/n Wireless Access Point
Use the XAP-1030 to:
Provide a Centrally Located High Performance Wi-Fi Network
Deliver “Whole Home” or Offi ce 802.11n Wi-Fi Coverage With
a Single Access Point
Increase Mobile Client Device Network Sensitivity
and Performance
Simplify Installation While Minimizing Setup Time and Expense
Eliminate Client Device Roaming Issues
AP

Quick Install Guide
2© Copyright 2015 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.
COMMERCIAL GRADE OMNI
802.11b/g/n Wireless Access Point
Model Number: XAP-1030
FCC ID: W59XAP103X
IC: 8584A-XAP103X
QUICK INSTALL GUIDE
© 2015 Luxul All rights reserved.
No part of this publication may be modifi ed or adapted in any way, for any
purposes without permission in writing from Luxul. The material in this manual
is subject to change without notice. Luxul reserves the right to make changes to
any product to improve reliability, function, or design. No license is granted, either
expressly or by implication or otherwise under any Luxul intellectual property rights.
An implied license only exists for equipment, circuits and subsystems contained in
this or any Luxul product.
This product is covered by one or more U.S. and foreign patents Patents: 7,379,717,
6,606,075, 6,373,448, other patents pending
DOCUMENT CONVENTIONS
The following graphical alerts are used in this document to indicate notable situations:
NOTE: Tips, hints, or special requirements that you should take note of.
CAUTION: Care is required. Disregarding a caution can result in data
loss or equipment malfunction.
WARNING!: Indicates a condition or procedure that could result in
personal injury or equipment damage.
FCC COMPLIANCE
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.

a: 14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | p: 801-822-5450
Quick Install Guide
3
a: 14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | p: 801-822-5450
33
WARNINGS
Read all installation instructions and site survey reports, and verify correct equip-
ment installation before connecting the XAP-1030 to its power source.
Remove jewelry and watches before installing this equipment.
Verify that the unit is grounded before connecting it to the power source.
Verify that any device connected to this unit is properly wired and grounded.
Connect all power cords to a properly wired and grounded electrical circuit.
Verify that the electrical circuits have appropriate overload protection.
Attach only approved power cords to the device.
Verify that the power connector and socket are accessible at all times during the
operation of the equipment.
Do not work with power circuits in dimly lit spaces.
Do not install this equipment or work with its power circuits during thunder-
storms or other weather conditions that could cause a power surge.
Verify there is adequate ventilation around the device, and that ambient tem-
peratures meet equipment operation specifi cations.
Products outside the approved confi gurations may be in violation of Part 15 of
the FCC Rules.
SITE PREPARATION
Consult your site survey and network analysis reports to determine specifi c
equipment placement, power drops, and so on.
Assign installation responsibility to the appropriate personnel.
Identify and document where all installed components are located.
Provide a suffi cient number of power drops for your equipment.
Ensure adequate, dust-free ventilation to all installed equipment.
Identify and prepare Ethernet and console port connections.
Verify that cable lengths are within the maximum allowable distances for optimal
and certifi ed signal transmission.

Quick Install Guide
4© Copyright 2015 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.
GETTING STARTED
System Requirements
Devices Supporting 802.11b, 802.11g or 802.11n
Web Browser (Microsoft IE 8.0 and up, Mozilla Firefox 10 and up, Safari 2.0 and
up, Google Chrome 4.0 and up, Opera 10 and up)
CAT5 Ethernet Cable
AC Power Socket (100 – 240 V, 50/60 Hz)
Internet Connection to View Documentation Online
Package Contents
XAP-1030 Wireless Access Point
5dBi Dipole Antenna
POE Injector, Power Adapter, Noise Suppresser
Four Rubber Feet for Desktop Mounting
Quick Install Guide
NOTE: If any of the listed items are missing or damaged, please contact
the reseller from whom you purchased for return/replacement.
Safety Information
To maintain the safety of users and property, follow these safety instructions:
The XAP-1030 wireless access point is designed for indoor use only. DO NOT
place this access point outdoors. If you require an outdoor access point, please
consider the Luxul XAP-1040.
DO NOT install this access point in or near hot or humid places, such as a kitchen
or bathroom. Take care to minimize exposure to excessive heat or moisture.
DO NOT pull any connected cable with force. When disconnecting cables, do so
by disconnecting fi rst from the access point. When reconnecting, connect the AP
fi rst and then the Power/data source.
When installing the access point, be sure it is fi rmly secured.
Accessories of this access point, such as mounting screws, the POE injector and
power supply may be dangerous to small children under 3 years of age. KEEP All
ACCESSORIES OUT OF THE REACH OF CHILDREN!

a: 14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | p: 801-822-5450
Quick Install Guide
5
a: 14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | p: 801-822-5450
55
The access point may become hot when in use for extended time periods. This is
normal and is not a malfunction. DO NOT install this access point where it will
be exposed to paper, cloth or other fl ammable materials. If not using the electri-
cal box included with the unit, ALWAYS use a properly shielded and UL listed
electrical box for installation.
The XAP-1030 contains no user-serviceable parts. If the access point is not
working properly, contact your dealer and ask for help. DO NOT attempt to
disassemble the access point.
HARDWARE FEATURES AND INSTALLATION
The XAP-1030 high powered access point is designed for optimal performance as
well as for simple and effi cient installation and setup. It implements Luxul’s 3D™
high performance technology and is packaged for installation on a shelf or wall. It
can also be placed discreetly in a closet, attic or other non-public area. Note that
the signal generated by the XAP-1030 is Omnidirectional and the unit should be
placed in a location that is central to the desired coverage area. The XAP-1030 is
optimal for use in single level or two level installations where the network access is
centrally located, the desired coverage area is substantially the same distance on all
sides (i.e. square) and the total area does not exceed 5,000 square feet.
Front View
On the front of the XAP-1030 are 4 LEDs. LEDs indicate 1) Power, 2) LAN Link/
Activity, 3) WLAN Status and 4) Bridge Mode.
XAP-1030 Front View

Quick Install Guide
6© Copyright 2015 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.
Status Indicators:
The XAP-1030 has four LEDs, positioned horizontally on the bottom right side of
the front of the access point. When viewed left to right, LEDs are as follows: 1)
Power (Green); 2) LAN Link/Activity (Amber); 3) WLAN Status (Blue); and 4) Bridge
Mode (Green).
The following table describes the LED functionality:
Indicator Name Description
Bridge Mode On Bridge is connected
Flashing Bridge Mode enabled but not connected
Off The AP is in default “Access Point” mode.
WLAN Status On The wireless radio is active and wireless
access is enabled
Off The wireless radio is not active and wireless
access is disabled
LAN Link/Activity On There is an active Ethernet connection
Flashing Indicates Ethernet activity
Off There is no active Ethernet connection
Power On The power is on
Off No power, check power connections
At startup, the Green Power LED will stay on while the amber LAN Link light
fl ashes. The blue LED will come on once the XAP-1030 wireless radio is active.
Top View
The Top of the XAP-1030 provides one SMA antenna connector and one RJ-45 con-
nection that is used to deliver both power and data to the access point.
XAP-1030 Top View

a: 14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | p: 801-822-5450
Quick Install Guide
7
a: 14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | p: 801-822-5450
77
Rear View
The Rear of the XAP-1030 has two key holes to allow for easy and fl exible mounting
on a wall or other solid surface. For desktop or shelf mounting, it also has guides
for placement of the four rubber feet provided.
XAP-1030 Rear View
Reset Button:
The Reset button is used to clear the current settings of the XAP-1030 and restore
factory default settings.
To Restore the Default Settings: With the XAP-1030 powered on, press and hold
the Reset button for 15 seconds. When all the LEDs except the power LED turn off,
release the reset button. The power LED will stay solid. The XAP-1030 will be set to
factory defaults.
CAUTION: Pressing and holding the Reset button will remove any
custom confi gurations done to the XAP-1030.
Environmental Requirements
Ethernet cable to provide Power and Data to the XAP-1030.
A computer supporting TCP/IP and equipped with a Web browser. Supported
Web browser versions include Microsoft IE 7.0 and up, Safari 1.0 and up, Mozilla
Firefox 1.0 and up, and Google Chrome 5.0 and up. The Web browser is used to
confi gure the XAP-1030.
The XAP-1030 uses 36-57VDC power. The POE injector power supply requires AC
100V ~ 240V, 50Hz ~ 60Hz.

Quick Install Guide
8© Copyright 2015 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.
Temperature of the operating environment: -04F~140F (-20C to 60C). Be sure to
place the access point away from heat generating devices.
Humidity of the operating environment: 5%-95% non-condensing. Do not place
the access point in an extremely dirty or damp location.
Keep the access point away from strong electromagnetic fi elds (i.e. Air
Conditioner compressors, fl uorescent light ballasts, CRT monitors/televisions,
etc.), and free from vibration, dust and direct sun light.
Hardware Installation
Access Point Placement
This XAP-1030 uses an omni-directional antenna which is designed to provide 360
degrees of coverage. For maximum effi ciency, it should be placed as close as pos-
sible in the center of the area in which you would like to provide coverage.
XAP-1030 Coverage Pattern
Mounting the Access Point on a Wall
The XAP-1030 can be mounted directly to a wall. It can also be placed on a
desktop, shelf, or other fl at surface. Once the location has been selected, mounting
the access point directly to the wall or place it on a fl at surface as demonstrated
below:
5.5”
139.7mm

a: 14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | p: 801-822-5450
Quick Install Guide
9
a: 14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | p: 801-822-5450
99
Mounting holes to secure the XAP-1030 to a wall
Install Included Rubber Feet in the Impressions in the bottom of the XAP-1030
Antenna Installation and Alignment
The XAP-1030 includes a 5dBi omni-directional antenna. To install the antenna,
simply align the connectors and turn it clock-wise until it is fi rmly attached. DO
NOT over tighten.
If the Omni Antenna is leaning, the pattern produced by it will lean as well
NOTE: Regardless of how the XAP-1030 is mounted, be sure to orient
the antenna vertically as demonstrated in the diagrams above.
Connecting the Ethernet Cable
With the XAP-1030 properly mounted and the Antenna installed, you can now plug
the Ethernet Cable into the RJ-45 connector.
NOTE: Category-5, super Category-5 or Category-6 unshielded twisted
pair (CAT5/CAT5e/CAT6 UTP) cables can be used. For best
results, it is recommended that Category-6 shielded twisted pair
be used to ensure stable data transmission at highest data rates.

Quick Install Guide
10 © Copyright 2015 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.
Connecting to the Power Source
The XAP-1030 is POE ready and supports Legacy (48v 1a), 802.3af, and 802.3at
POE injectors. A POE injector is included with the device. To apply power, simply
connect the opposite end of the Ethernet cable to which the access point is
already connected to the provided POE injector or other POE switch or injector. An
Ethernet cable length of up to 300 feet can be used. DO NOT yet apply power to
the POE injector or switch.
NOTE: To ensure FCC compliance and minimize high frequency noise, a
Ferrite Noise Suppresser is included with the POE injector kit. It
should be placed on the Ethernet cable at or near the connector
on the end of the Ethernet cable that plugs into the POE device.
To install it, simply unsnap the plastic fasteners, place it on the
Ethernet cable as demonstrated below and re-snap the plastic
fasteners to secure it in place.
Connecting to the Internet Source
This Luxul device is not a router and in most installations will be connected to a
Router or Switch in order to deliver Internet access. To do so, connect the POE
injector (or switch) to the desired Internet source using another Ethernet cable. Be
sure the source device is powered off.
POE
Injector
Power
Source
Power
In
Ferrite Noise
Suppresser
Data
Source
Poe
Device Data/Pwr Out
Data
In
The POE Injector Sends Power and Signal Over One Ethernet Cable
Applying Power
Once the Ethernet cables have been properly connected, connect the power sup-
ply to the POE injector and plug it in to a standard AC power outlet. Or, if plugging
into a POE switch, turn the switch (or appropriate port) on. The network source
device can also now be powered back on.
NOTE: If your Internet source (Router or Switch) is a POE enabled device
and connected via POE, it can be plugged directly into the access
point without the need to run a separate POE injector.

a: 14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | p: 801-822-5450
Quick Install Guide
11
a: 14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | p: 801-822-5450
1111
LED Visual Verifi cation
With power applied, you can now verify that the XAP-1030 is connected and
functioning properly. Prior to placing the access point cover plate, perform a visual
inspection of the LEDs. The Green PWR LED (on the left) should be on while the
amber LAN light fl ashes, indicating activity. Once the XAP-1030 is properly con-
nected to the Internet source, the blue WLAN LED should also remain on. The
Green BRG LED at the right will only be on if the access point is set to function in
bridge mode.
LEDs on the front of the XAP-1030
CONFIGURATION
NOTE: Confi guring the Luxul AP with non-Luxul routers may require
your computer’s IP address to be changed.
The Luxul XAP-1030 default IP addresss is 192.168.0.12. If the IP
address of your router is not set to the 192.168.0.X network,
a temporary static IP address must be set on the computer
being used for confi guration. To do so, set the IP address of the
computer to the 192.168.0.X range and then use the default IP
address of your XAP-1030 (192.168.0.12) as the Gateway/Router.
Once confi gured, set the computer IP confi guration back to
“Obtain Automatically/DHCP.”
Go to http://luxul.com/how-to-videos for videos about
changing the IP address of your Operating System.
Login
The XAP-1030 is not equipped with internal DHCP server. If connected to the Luxul
XBR-2300 Enterprise Dual-WAN Router, confi guration will be automatic. Otherwise,
the IP address of the computer for login and confi guration will need to be manually
confi gured. The table below lists the default parameters of the XAP-1030.

LUX-QIG-XAP-1030
029150953
a: 14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685
p: 801-822-5450
Information on this document supersedes all previous versions.
Products and documents subject to change without notice.
Products may be discontinued without notice.
luxul.com
Parameter Default Value
Default IP address 192.168.0.12
Default user name admin
Default password admin
Login to the XAP-1030 Wireless Access Point with the following steps:
a. Be sure the XAP-1030 is properly installed and powered on
b. Open your Web Browser, and enter http://192.168.0.12.
The login window appears as shown below:
c. Enter the user name and password (default user name is ”admin” and default
password is “admin”), and then click “OK” to login to the Quick Setup window.
Quick Setup
For confi guration instructions download the XAP-1020 User Guide from luxul.com.
To check for fi rmware updates visit http://luxul.com/fi rmware