Luxul XAP-1030 User manual

luxul.com
Simply Connected
User Guide
XAP-1030
Luxul Xen™ Commercial Grade Omni
802.11b/g/n Wireless Access Point
Use the XAP-1030 to:
XProvide a Centrally Located High Performance Wi-Fi Network
XDeliver “Whole Home” or Office 802.11n Wi-Fi Coverage With
a Single Access Point
XIncrease Mobile Client Device Network Sensitivity
and Performance
XSimplify Installation While Minimizing Setup Time and Expense
XEliminate Client Device Roaming Issues
AP

User Guide
2© Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.
COMMERCIAL GRADE OMNI
802.11b/g/n Wireless Access Point
Model Number: XAP-1030
FCC ID: W59XAP103X
IC: 8584A-XAP103X
USER GUIDE
© 2011 Luxul. All Rights Reserved.
No part of this publication may be modified or adapted in any way, for any
purposes without permission in writing from Luxul. The material in this manual
is subject to change without notice. Luxul reserves the right to make changes to
any product to improve reliability, function, or design. No license is granted, either
expressly or by implication or otherwise under any Luxul intellectual property rights.
An implied license only exists for equipment, circuits and subsystems contained in
this or any Luxul product.
This product is covered by one or more U.S. and foreign patents Patents: 7,379,717,
6,606,075, 6,373,448, other patents pending
DOCUMENT CONVENTIONS
The following graphical alerts are used in this document to indicate notable situations:
NOTE: Tips, hints, or special requirements that you should take note of.
CAUTION: Care is required. Disregarding a caution can result in data
loss or equipment malfunction.
WARNING!: Indicates a condition or procedure that could result in
personal injury or equipment damage.
FCC COMPLIANCE
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.

luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460
User Guide
3
CONTENTS
1 INTRODUCTION 4
1.1 Warnings 5
1.2 Site Preparation 5
2 XAP-1030 SPECIFICATIONS 6
3 GETTING STARTED 7
3.1 System Requirements 7
3.2 Package Contents 7
3.3 Safety Information 7
4 HARDWARE FEATURES AND INSTALLATION 8
4.1 Front View 8
4.2 Top View 10
4.3 Rear View 10
4.3 Environmental Requirements 11
4.4 Hardware Installation 11
5 CONFIGURATION 15
5.1 Login 15
5.2 Quick Setup 16
5.3 Wireless 19
5.4 Maintenance 22
5.6 Status 24
6 REGULATORY COMPLIANCE 26
6.1 Health and Safety Recommendations 26
6.2 RF Exposure Guidelines 26
6.3 Radio Frequency Interference Requirements—FCC 27
6.4 Radio Transmitters (Part 15) 28
6.5 Industry Canada (RSS-Gen Issue 2) 28
APPENDIX 1: TECHNICAL SUPPORT 28

User Guide
4© Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.
1 INTRODUCTION
Congratulations on your purchase of the Luxul Xen™ Commercial Grade Omni
802.11n Wireless Access Point (XAP-1030). The XAP-1030 provides superior
Omnidirectional Wi-Fi coverage in a sturdy and versatile metal enclosure for
deployment in post-construction residential and commercial Wi-Fi installations.
The XAP-1030 is designed to be placed inconspicuously in a centrally located utility
closet or other non-public indoor location. It can be mounted on a wall or simply
placed on a shelf or cabinet. Powered by Luxul’s Xen3D™ Technology, the XAP-1030
enhances data throughput and coverage by as much as 400% over traditional Wi-Fi
gear, providing for whole home or small office coverage with a single access point.
With this high performance wireless access point, computers and wireless devices
that are compatible with 802.11b/g and/or 802.11n can sustain maximum data rates
and improved overall performance at significantly greater distances.
The XAP-1030 features Luxul’s XenSmart™ web based management interface.
XenSmart provides a powerful, yet simple method for setting up and optimizing
the wireless network. The XAP-1030 is also XenConnect™ enabled for optimal per-
formance and installation simplicity when deployed together with Luxul Routers,
Gigabit Switches, and other Luxul products.
XAP-1030 Features:
XImplements Patented Xen3D™ Technology for Enhanced Throughput and
Coverage
XHighest FCC Approved Performance (Effective EIRP 36dBm) for Farther Reaching
Signal and Maximum Data Rates
X18dB of Receive Gain Increases Client Device Network Sensitivity and
Performance
XComplies with 2.4 GHz IEEE 802.11n Standard. Backward Compatible with IEEE
802.11g/b
XSupports WMM QoS Functionality to Prioritize Multimedia Traffic
XEnhanced Multi-Level Security with WPA-PSK (TKIP, AES, TKIP & AES), WPA2-PSK
(AES), WPA-PSK/WPA2-PSK Personal (TKIP & AES) and 128-bit WEP
XSupports up to 8 SSIDs with Individual Security Settings
XMultiple SSIDs Support VLAN Tagging (1 VLAN per SSID)
XSingle Cable Installation with PoE (supports both IEEE 802.3af and Legacy)
XFirmware Upgradeable
XEasy 3 Step Setup through Web-based XenSmart™ User Interface

luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460
User Guide
5
XInstalls Directly on a Wall or Shelf; or Can be Placed Discreetly in a Closet or
Other Non-Public Area
XXenConnect™ Enabled for Maximum Compatibility and Performance with Other
Luxul Xen Products
1.1 Warnings
XRead all installation instructions and site survey reports, and verify correct equip-
ment installation before connecting the XAP-1030 to its power source.
XRemove jewelry and watches before installing this equipment.
XVerify that the unit is grounded before connecting it to the power source.
XVerify that any device connected to this unit is properly wired and grounded.
XConnect all power cords to a properly wired and grounded electrical circuit.
XVerify that the electrical circuits have appropriate overload protection.
XAttach only approved power cords to the device.
XVerify that the power connector and socket are accessible at all times during the
operation of the equipment.
XDo not work with power circuits in dimly lit spaces.
XDo not install this equipment or work with its power circuits during thunder-
storms or other weather conditions that could cause a power surge.
XVerify there is adequate ventilation around the device, and that ambient tem-
peratures meet equipment operation specifications.
XProducts outside the approved configurations may be in violation of Part 15 of
the FCC Rules.
1.2 Site Preparation
XConsult your site survey and network analysis reports to determine specific
equipment placement, power drops, and so on.
XAssign installation responsibility to the appropriate personnel.
XIdentify and document where all installed components are located.
XProvide a sufficient number of power drops for your equipment.
XEnsure adequate, dust-free ventilation to all installed equipment.
XIdentify and prepare Ethernet and console port connections.
XVerify that cable lengths are within the maximum allowable distances for optimal
and certified signal transmission.

User Guide
6© Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.
2 XAP-1030 SPECIFICATIONS
Standards IEEE 802.11n
IEEE 802.11b/g
IEEE 802.3af
Hardware LAN Port: 1 RJ45 10/100 Mbps data and power input
5dBi Omnidirectional Dipole Antenna
System LEDs: Power, WLAN active, LAN link/activity,
Bridge mode active.
RJ45 Connection LEDs: The RJ45 connection on the top
of the unit has two LEDs that indicate power and LAN
link/activity.
RF Information Frequency Band: 2.401 – 2.473GHz
Operating Channels: 11
Available Transmit Power 2.401 – 2.473GHz (IEEE802.11g/n):
Up to 36dBm EIRP
w30dBm @ 6~9Mbps / MCS0
w29dBm @ 12~18Mbps / MCS1-2
w27dBm @ 24~36Mbps / MCS3-4
w26dBm @ 48~54Mbps / MCS5-7
2.401 – 2.473GHz (IEEE802.11b):
Up to 36dBm EIRP
w30dBm @ 1~11Mbps
Available Receive Gain  2.401 – 2.473GHz (IEEE802.11g/n):
Up to 18dBm
2.401 – 2.473GHz (IEEE802.11b):
Up to 18dBm
Receive Sensitivity
(Typical)
2.401 – 2.473GHz (IEEE802.11n): Up to -91dBm
2.401 – 2.473GHz (IEEE802.11g): Up to -92dBm
2.401 – 2.473GHz (IEEE802.11b): Up to -93dBm
Wireless Operation Modes Access Point
Point-to Point Wireless Bridge
Point-to-Multipoint Wireless Bridge
Management and Security XenSmart™ Remote Web-based Management
WEP (128 bit)
WPA-PSK (TKIP, AES, TKIP&AES)
WPA2-PSK (AES)
WPA-PSK/WPA2-PSK Auto (TKIP&AES)
Web Based Firmware Upgrade
QoS: Wireless Multi-Media (WMM) Extensions
Certifications FCC Part 15, Class B

luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460
User Guide
7
Power Requirements Ethernet POE in: 48VDC/0.375A for IEEE 802.3af
Compliance
Power Consumption: 5W Nominal, 13W Max
Temperature Range Operating: -4°F to 140°F (-20°C to 60°C)
Storage: -40°F to 158°F (-40°C to 70°C)
Operating Humidity 5% to 95% (Non-condensing)
Mechanical Access Point Dimensions WxHxD: 7”(177.8mm) x
4”(101.6mm) x 1.25”(31.75mm)
Weight Item: 1.2 lbs
With Packaging: 2 lbs
3 GETTING STARTED
3.1 System Requirements
XDevices Supporting 802.11b, 802.11g or 802.11n
XWeb Browser (Microsoft IE 7.0 and up, Mozilla Firefox 1.0 and up, Safari 1.0 and up,
Google Chrome 5.0 and up)
XCAT5 Ethernet Cable
XAC Power Socket (100 – 240 V, 50/60 Hz)
XInternet Connection to View Documentation Online
3.2 Package Contents
XXAP-1030 Wireless Access Point
X5dBi Dipole Antenna
XPOE Injector, Power Adapter, Noise Suppresser
XFour Rubber Feet for Desktop Mounting
XQuick Install Guide
NOTE: If any of the listed items are missing or damaged, please contact
the reseller from whom you purchased for return/replacement.
3.3 Safety Information
To maintain the safety of users and property, follow these safety instructions:
XThe XAP-1030 wireless access point is designed for indoor use only. DO NOT
place this access point outdoors. If you require an outdoor access point, please
consider the Luxul XAP-1040.
XDO NOT install this access point in or near hot or humid places, such as a kitchen
or bathroom. Take care to minimize exposure to excessive heat or moisture.

User Guide
8© Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.
XDO NOT pull any connected cable with force. When disconnecting cables, do so
by disconnecting first from the access point. When reconnecting, connect the AP
first and then the Power/data source.
XWhen installing the access point, be sure it is firmly secured.
XAccessories of this access point, such as mounting screws, the POE injector and
power supply may be dangerous to small children under 3 years of age. KEEP All
ACCESSORIES OUT OF THE REACH OF CHILDREN!
XThe access point may become hot when in use for extended time periods. This is
normal and is not a malfunction. DO NOT install this access point where it will
be exposed to paper, cloth or other flammable materials. If not using the electri-
cal box included with the unit, ALWAYS use a properly shielded and UL listed
electrical box for installation.
XThe XAP-1030 contains no user-serviceable parts. If the access point is not
working properly, contact your dealer and ask for help. DO NOT attempt to
disassemble the access point.
4 HARDWARE FEATURES AND INSTALLATION
The XAP-1030 high powered access point is designed for optimal performance as
well as for simple and efficient installation and setup. It implements Luxul’s Xen3D™
high performance technology and is packaged for installation on a shelf or wall. It
can also be placed discreetly in a closet, attic or other non-public area. Note that
the signal generated by the XAP-1030 is Omnidirectional and the unit should be
placed in a location that is central to the desired coverage area. The XAP-1030 is
optimal for use in single level or two level installations where the network access is
centrally located, the desired coverage area is substantially the same distance on all
sides (i.e. square) and the total area does not exceed 5,000 square feet.
4.1 Front View
On the front of the XAP-1030 are 4 LEDs. LEDs indicate 1) Power, 2) LAN Link/
Activity, 3) WLAN Status and 4) Bridge Mode.

luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460
User Guide
9
XAP-1030 Front View
Status Indicators:
The XAP-1030 has four LEDs, positioned horizontally on the bottom right side of
the front of the access point. When viewed left to right, LEDs are as follows: 1)
Power (Green); 2) LAN Link/Activity (Amber); 3) WLAN Status (Blue); and 4) Bridge
Mode (Green).
The following table describes the LED functionality:
Indicator
Name
Description
PWR
(Power)
On The wireless radio is active and wireless access is
enabled an active connection to the internet
Off The wireless radio is not active and wireless
access is disabled
LAN
(LAN Status
Link/Activity)
On There is an active Ethernet connection
Flashing Indicates Ethernet activity
Off There is no active Ethernet connection

User Guide
10 © Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.
Indicator
Name
Description
WLAN
(Wireless
LAN Status)
On The wireless radio is active and wireless access is
enabled an active connection to the internet
Off The wireless radio is not active and wireless
access is disabled
BRG
(Bridge Mode)
On Bridge Mode is enabled
Off The AP is in default “Access Point” mode.
At startup, the Green Power LED will stay on while the amber LAN Link light
flashes. The blue LED will come on once the XAP-1030 radio is active.
4.2 Top View
The Top of the XAP-1030 provides one SMA antenna connector and one RJ-45 con-
nection that is used to deliver both power and data to the access point.
XAP-1030 Top View
4.3 Rear View
The Rear of the XAP-1030 has two key holes to allow for easy and flexible mounting
on a wall or other solid surface. For desktop or shelf mounting, it also has guides
for placement of the four rubber feet provided.
XAP-1030 Rear View

luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460
User Guide
11
4.3 Environmental Requirements
XEthernet cable to provide Power and Data to the XAP-1030.
XA computer supporting TCP/IP and equipped with a Web browser. Supported
Web browser versions include Microsoft IE 7.0 and up, Safari 1.0 and up, Mozilla
Firefox 1.0 and up, and Google Chrome 5.0 and up. The Web browser is used to
configure the XAP-1030.
XThe XAP-1030 uses 36-57VDC power. The POE injector power supply requires AC
100V ~ 240V, 50Hz ~ 60Hz.
XTemperature of the operating environment: -04F~140F (-20C to 60C). Be sure to
place the access point away from heat generating devices.
XHumidity of the operating environment: 5%-95% non-condensing. Do not place
the access point in an extremely dirty or damp location.
XKeep the access point away from strong electromagnetic fields (i.e. Air
Conditioner compressors, fluorescent light ballasts, CRT monitors/televisions,
etc.), and free from vibration, dust and direct sun light.
4.4 Hardware Installation
4.4.1 Access Point Placement
This XAP-1030 uses an omni-directional antenna which is designed to provide 360
degrees of coverage. For maximum efficiency, it should be placed as close as pos-
sible in the center of the area in which you would like to provide coverage.
XAP-1030 Coverage Pattern
4.4.2 Mounting the Access Point on a Wall
The XAP-1030 can be mounted directly to a wall. It can also be placed on a desktop,
shelf, or other flat surface. Once the location has been selected, mounting the ac-
cess point directly to the wall or place it on a flat surface as demonstrated below:

User Guide
12 © Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.
5.5”
139.7mm
Mounting holes to secure the XAP-1030 to a wall
Install Included Rubber Feet in the Impressions in the bottom of the XAP-1030
4.4.3 Antenna Installation and Alignment
The XAP-1030 includes a 5dBi omni-directional antenna. To install the antenna,
simply align the connectors and turn it clock-wise until it is firmly attached. DO
NOT over tighten.
If the Omni Antenna is leaning, the pattern produced by it will lean as well

luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460
User Guide
13
NOTE: Regardless of how the XAP-1030 is mounted, be sure to orient
the antenna vertically as demonstrated in the diagrams above.
4.4.4 Connecting the Ethernet Cable
With the XAP-1030 properly mounted and the Antenna installed, you can now plug
the Ethernet Cable into the RJ-45 connector.
NOTE: Category-5, super Category-5 or Category-6 unshielded twisted
pair (CAT5/CAT5e/CAT6 UTP) cables can be used. For best
results, it is recommended that Category-6 shielded twisted pair
be used to ensure stable data transmission at highest data rates.
4.4.5 Connecting to the Power Source
The XAP-1030 is POE ready and supports Legacy (48v 1a), 802.3af, and 802.3at
POE injectors. A POE injector is included with the device. To apply power, simply
connect the opposite end of the Ethernet cable to which the access point is
already connected to the provided POE injector or other POE switch or injector. An
Ethernet cable length of up to 300 feet can be used. DO NOT yet apply power to
the POE injector or switch.
NOTE: To ensure FCC compliance and minimize high frequency noise, a
Ferrite Noise Suppresser is included with the POE injector kit. It
should be placed on the Ethernet cable at or near the connector
on the end of the Ethernet cable that plugs into the POE device.
To install it, simply unsnap the plastic fasteners, place it on the
Ethernet cable as demonstrated below and re-snap the plastic
fasteners to secure it in place.
4.4.6 Connecting to the Internet Source
This Luxul device is not a router and in most installations will be connected to a
Router or Switch in order to deliver Internet access. To do so, connect the POE
injector (or switch) to the desired Internet source using another Ethernet cable. Be
sure the source device is powered off.

User Guide
14 © Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.
Data
Source
Power
Source
Data
In
Power
In
Data/Pwr
Out
POE
Injector
Ferrite Noise
Suppresser
The POE Injector Sends Power and Signal Over One Ethernet Cable
4.4.7 Applying Power
Once the Ethernet cables have been properly connected, connect the power sup-
ply to the POE injector and plug it in to a standard AC power outlet. Or, if plugging
into a POE switch, turn the switch (or appropriate port) on. The network source
device can also now be powered back on.
NOTE: If your Internet source (Router or Switch) is a POE enabled device
and connected via POE, it can be plugged directly into the access
point without the need to run a separate POE injector.
4.4.8 LED Visual Verification
With power applied, you can now verify that the XAP-1030 is connected and
functioning properly. Prior to placing the access point cover plate, perform a visual
inspection of the LEDs. The Green PWR LED (on the left) should be on while the
amber LAN light flashes, indicating activity. Once the XAP-1030 is properly con-
nected to the Internet source, the blue WLAN LED should also remain on. The
Green BRG LED at the right will only be on if the access point is set to function in
bridge mode.

luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460
User Guide
15
LEDs on the front of the XAP-1030
5 CONFIGURATION
5.1 Login
The XAP-1030 is not equipped with internal DHCP server. If connected to the Luxul
XBR-2300 Enterprise Dual-WAN Router, configuration will be automatic. Otherwise,
the IP address of the computer for login and configuration will need to be manually
configured. The table below lists the default parameters of the XAP-1030.
Parameter Default Value
Default IP address 192.168.0.12
Default user name admin
Default password admin
Login to the XAP-1030 Wireless Access Point with the following steps:
a. Be sure the XAP-1030 is properly installed and powered on
b. Open your Web Browser, and enter http://192.168.0.12.
The login window appears as shown below:
c. Enter the user name and password (default user name is ”admin” and default
password is “admin”), and then click “OK” to login to the Quick Setup window.

User Guide
16 © Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.
5.2 Quick Setup
Quick Setup: For most installations, it is expected that the Quick Setup page will
be sufficient to optimally configure and deploy the XAP-1030 Wi-Fi network. The
Quick Setup page consists of the following:
XDHCP Client: Enabled or Disabled. DHCP (Dynamic Host Configuration Protocol)
is used to automatically assign an IP Addresses to a device on the network. If
DHCP is enabled on the Access Point, it will no longer use the static address set
by Luxul at time of manufacturing and will request a dynamic IP Address from the
Router (sometimes referred to as the Gateway).
When DHCP is enabled on the Access Point, the new IP address will be needed
in order to access the XenSmart™ web management interface. The Router web
interface can be used to look up the IP address assigned to the Access Point. To
Enable DHCP, click on the drop down menu and select Enable. Select Apply and
then Reboot for the change to take effect.
NOTE: DHCP is set as Disabled by default and is the recommended
setting in order to ensure optimal communications with all Luxul
Xen devices on the network.

luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460
User Guide
17
XIP Address: An IP address is a numerical label assigned to each device on the
network. This field shows the IP address that is assigned to the XAP-1030. To
ensure plug and play capability with other Luxul networking products, the IP
Address is automatically defaulted to 192.168.0.12. If desired, the user can set
this to a different static IP Address. To change the IP address of the Access Point,
simply type in the desired IP address (the text field will be red if the address is
incomplete), click Apply and then Reboot for the changed to take effect. When
connecting to the Access Point through the XenSmart™ web interface, the NEW IP
Address must be used.
NOTE: Each device on the same network must have a unique IP address.
If the Access Point is assigned an IP address already in use, it
will result in an IP address conflict that will need to be resolved
manually. For optimal communications with all Luxul Xen devices
on the network, it is recommended that IP addresses not be
changed unless absolutely necessary.
XSubnet Mask: To ensure plug and play capability with other Luxul networking
products, the Subnet Mask is automatically defaulted to 255.255.255.0. If desired,
the user can set this to a different static Subnet Mask.
XDefault Gateway: A gateway is a router on the network that connects two or
more networks together. Typically the gateway (router) connects the local area
network (LAN) to the Internet. The Internet Service Provider (ISP) often provides
a physical device (usually a DSL modem or cable modem) that connects to the
gateway with an Ethernet cable, thus completing the link to the Internet. For
optimal connectivity and network functionality, this device could also be the
Luxul Xen XBR-2300 Router.
The Default Gateway field is the IP address for this routing device. The default
configuration is left blank or empty, allowing the Access Point to automatically find
the necessary route to the Internet. It is recommended to leave this field blank.
XNetwork Name (SSID): Sets the name of the Wireless Network. Default name
is LuxulXen. It is recommended to change the SSID from the default name. The
SSID is case sensitive and can contain:
w2 – 32 alphanumeric characters
wSpaces
wSpecial characters (i.e. @#$%&*)
To change the SSID of the wireless network, simply type the desired name, click
Save, and then Reboot for the change to take effect.

User Guide
18 © Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.
XSecurity Mode: Sets the wireless security encryption mode. It is HIGHLY
recommended to change the Security Mode and use the highest security level
supported by the client devices in the network. In most wireless networks, WPA/
WPA2 Personal is an excellent option that will support the largest cross section
of client devices. Security options include:
wOpen (default - no security)
wWEP (128 bit shared key)
wWPA Personal
wWPA2 Personal
wWPA/WPA2 Personal
To change the Security Mode, click the drop down menu and select the desired
mode. The available options for the selected mode will then appear. AFTER all
options are complete, click Save, and then Reboot for the change to take effect.
XEncryption: This field sets the type of encryption to be used by the Security
Mode. The encryption options are dependent upon the Security Mode selected
and this field only shows while in WPA mode. For WEP and WPA2, and WPA/
WPA2 Personal, encryption is automatically set to 128 bits, AES, and TKIP &
AES respectively. For WPA, there are three options: AES, TKIP, and TKIP & AES.
When set to WPA, it is recommended that TKIP & AES be used. To change the
Encryption, click the drop down menu and select the desired encryption type.
Once all options are selected, click Save and then Reboot for the change to take
effect.
XWEP Key: This field only shows while in WEP mode and sets the WEP key to be
used in the network. WEP 128 bit keys require 26 characters. Allowed characters
are numbers 0-9 and letters a-f. There are WEP key generators online that can
automatically create a key. To change the WEP Key, simply enter the 26 character
key then click Save and then Reboot for the change to take effect.
XWPA Passphrase: This sets the passphrase used by client devices to connect to
the wireless network when using WPA Security Mode. For WPA the passphrase:
wMust be a minimum of 8, maximum of 63 characters
wCan contain spaces or special characters (i.e. @#$%&*)
To change the WPA Passphrase, simply type in the desired passphrase, click Save,
then Reboot for the change to take effect.

luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460
User Guide
19
NOTE: It is recommended to use a strong password containing:
wMore than the minimum number of characters
wOne or more capital letters
wNumbers and/or special characters
XAdministrator Login: Sets the password for Administrator access to the
XenSmart™ web management interface. When connecting to the Access Point
through the XenSmart™ web interface, the user is prompted for a User ID (this is
always admin) and Password (the default value is “admin”). It is HIGHLY recom-
mended to change to a secure password when initially configuring the Access
Point. To change the password, simply enter the new password, confirm the
password, then click Save, and then Reboot for the change to take effect.
After confirming the desired Quick Setup configuration settings, select Save and
then Reboot for the settings to take effect.
5.3 Wireless
5.3.1 Basic Wireless Settings
Basic Wireless Settings: This screen allows the modification of the following basic
settings for the wireless network:
XWireless Radio: This field is used to Enable and Disable the wireless network
and is set to Enabled by default. If the Radio is Disabled the Access Point will not
broadcast a wireless signal. To Disable the Wireless Radio, click the dropdown
menu, select Disabled, then click Save and then Reboot for the change to take
effect.

User Guide
20 © Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.
XChannel: This field allows the user to set which 2.4GHz channel to use. The
default is set to Channel 6 and is the recommended setting due to the Access
Point being optimized to run on Channel 6. However, any other channel (1-11) may
be selected. To change the Channel, click the dropdown menu, select the desired
channel, then click Save and then Reboot for the change to take effect.
XWireless Mode: Sets the type of 802.11 wireless network to be broadcast.
Available modes are:
w11g (802.11g)
w11gnHT20 (802.11g/n with 20MHz only channels)
w11gnHT40+ (802.11g/n with 20/40MHz channels expanding to channels above
the set channel)
w11gnHT40- (802.11g/n with 20/40MHz channels expanding to channels below
the set channel)
The default setting is 11gnHT20, and is recommended for optimal performance of
all types of devices in the network. Use the 11g Mode ONLY if there are 802.11b/g
client devices in the network that will not connect in 11gnHT20 Mode. 11gnHT40+
and 11gnHT40- Modes should only be used when all client devices in the network
are 802.11n and capable of supporting 40MHz channels.
XChannel Width: Sets the width of the 802.11n channel. Available widths are:
w20MHz (only available for 11g and 11gnHT20 modes)
w40MHZ (only available for 11gnHT40+ and 11gnHT40-)
w20/40MHz Auto (available for all modes)
The default (and recommended) setting is 20/40 MHz Auto to provide maximum
performance to all client devices and to avoid any potential client issues.
NOTE: HT40 mode will use two channels. For example, if HT40- is
selected and the radio is using channel 6, it would also use
channel 1. If HT40+ is selected and the radio is using channel 6, it
would also use channel 11.
If making any change to the Wireless Settings, select Save and then Reboot for the
settings to take effect.