Luxul XAP-1020 User manual

luxul.com
Simply Connected
User Guide
XAP-1020
Luxul Xen™ Low Profile
802.11b/g/n Wireless Access Point
Use the XAP-1020 to:
XProvide an Unobtrusive Wireless Network that Minimizes
Unsightly Cables or Equipment
XDeliver “Whole Home” or Office 802.11n Wi-Fi Coverage With a
Single Access Point
XIncrease Mobile Client Device Network Sensitivity and
Performance
XSimplify Installation While Minimizing Setup Time and Expense
XEliminate Client Device Roaming Issues
AP

User Guide
2© Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.
LUXUL XEN HIGH PERFORMANCE LOW PROFILE
802.11b/g/n Wireless Access Point
Model Number: XAP-1020
FCC ID: W59XAP101020
IC: 8584A-XAP101020
USER GUIDE
© 2011 Luxul. All Rights Reserved.
No part of this publication may be modified or adapted in any way, for any
purposes without permission in writing from Luxul. The material in this manual
is subject to change without notice. Luxul reserves the right to make changes to
any product to improve reliability, function, or design. No license is granted, either
expressly or by implication or otherwise under any Luxul intellectual property rights.
An implied license only exists for equipment, circuits and subsystems contained in
this or any Luxul product.
This product is covered by one or more U.S. and foreign patents Patents: 7,379,717,
6,606,075, 6,373,448, other patents pending
DOCUMENT CONVENTIONS
The following graphical alerts are used in this document to indicate notable situations:
NOTE: Tips, hints, or special requirements that you should take note of.
CAUTION: Care is required. Disregarding a caution can result in data
loss or equipment malfunction.
WARNING!: Indicates a condition or procedure that could result in
personal injury or equipment damage.
FCC COMPLIANCE
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.

luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460
User Guide
3
CONTENTS
1 INTRODUCTION 4
1.1 Warnings 5
1.2 Site Preparation 5
2 XAP-1010 SPECIFICATIONS 5
3 GETTING STARTED 7
3.1 System Requirements 7
3.2 Package Contents 7
3.3 Safety Information 7
4 HARDWARE FEATURES AND INSTALLATION 8
4.1 Front View 8
4.2 Rear View 10
4.3 Environmental Requirements 11
4.4 Hardware Installation 12
5 CONFIGURATION 16
5.1 Login 16
5.2 Quick Setup 16
5.3 Wireless 20
5.4 Maintenance 23
5.5 QoS 25
5.6 Status 26
6 REGULATORY COMPLIANCE 27
6.1 Health and Safety Recommendations 27
6.2 RF Exposure Guidelines 28
6.3 Radio Frequency Interference Requirements—FCC 28
6.4 Radio Transmitters (Part 15) 29
6.5 Industry Canada (RSS-Gen Issue 2) 29
APPENDIX 1: TECHNICAL SUPPORT 29

User Guide
4© Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.
1 INTRODUCTION
Congratulations on your purchase of the Luxul Xen™ Low Profile 802.11n Wireless
Access Point (XAP-1020). The XAP-1020 provides superior Wi-Fi coverage while
maintaining a discreet, elegant profile for deployment in post-construction resi-
dential and commercial Wi-Fi installations. The XAP-1020 can be installed directly
on a wall or ceiling, or mounted to the included adjustable wall bracket that allows
the access point to be “aimed” for optimal coverage. Powered by Luxul’s Xen3D™
Technology, the XAP-1020 enhances data throughput and coverage by as much as
400% over traditional Wi-Fi gear, providing for whole home or small office cover-
age with a single access point. With this high performance wireless access point,
computers and wireless devices that are compatible with 802.11b/g and/or 802.11n
can sustain maximum data rates and improved overall performance at significantly
greater distances.
The XAP-1020 features Luxul’s XenSmart™ web based management interface.
XenSmart provides a powerful, yet simple method for setting up and optimizing
the wireless network. The XAP-1020 is also XenConnect™ enabled for optimal per-
formance and installation simplicity when deployed together with Luxul Routers,
Gigabit Switches, and other Luxul products.
XAP-1020 Features:
XImplements Patented Xen3D™ Technology for Enhanced Throughput and
Coverage
XHighest FCC Approved Performance (Effective EIRP 36dBm) for Farther Reaching
Signal and Maximum Data Rates
X18dB of Receive Gain Increases Client Device Network Sensitivity and
Performance
XComplies with 2.4 GHz IEEE 802.11n Standard. Backward Compatible with IEEE
802.11g/b
XSupports WMM QoS Functionality to Prioritize Multimedia Traffic
XEnhanced Multi-Level Security with WPA-PSK (TKIP, AES, TKIP & AES), WPA2-PSK
(AES), WPA-PSK/WPA2-PSK Personal (TKIP & AES) and 128-bit WEP
XSupports up to 8 SSIDs with Individual Security Settings
XMultiple SSIDs Support VLAN Tagging (1 VLAN per SSID)
XSingle Cable Installation with PoE (supports both IEEE 802.3af and Legacy)
XFirmware Upgradeable
XEasy 3 Step Setup through Web-based XenSmart™ User Interface

luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460
User Guide
5
XInstalls Discreetly on Wall or Ceiling
XXenConnect™ Enabled for Maximum Compatibility and Performance with Other
Luxul Xen Products
1.1 Warnings
XRead all installation instructions and site survey reports, and verify correct equip-
ment installation before connecting the XAP-1020 to its power source.
XRemove jewelry and watches before installing this equipment.
XVerify that the unit is grounded before connecting it to the power source.
XVerify that any device connected to this unit is properly wired and grounded.
XConnect all power cords to a properly wired and grounded electrical circuit.
XVerify that the electrical circuits have appropriate overload protection.
XAttach only approved power cords to the device.
XVerify that the power connector and socket are accessible at all times during the
operation of the equipment.
XDo not work with power circuits in dimly lit spaces.
XDo not install this equipment or work with its power circuits during thunder-
storms or other weather conditions that could cause a power surge.
XVerify there is adequate ventilation around the device, and that ambient tem-
peratures meet equipment operation specifications.
XProducts outside the approved configurations may be in violation of Part 15 of
the FCC Rules.
1.2 Site Preparation
XConsult your site survey and network analysis reports to determine specific
equipment placement, power drops, and so on.
XAssign installation responsibility to the appropriate personnel.
XIdentify and document where all installed components are located.
XProvide a sufficient number of power drops for your equipment.
XEnsure adequate, dust-free ventilation to all installed equipment.
XIdentify and prepare Ethernet and console port connections.
XVerify that cable lengths are within the maximum allowable distances for optimal
and certified signal transmission.

User Guide
6© Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.
2 XAP-1020 SPECIFICATIONS
Standards IEEE 802.11n
IEEE 802.11b/g
IEEE 802.3af
Hardware LAN Port: 1 RJ45 10/100 Mbps data and power input
 7dBi Circular Polarized Directional Antenna
LEDs: All LEDs are internal and not visible when cover
plate is in place (Power, WLAN active, LAN link/
activity, Bridge mode active).
RF Information Frequency Band: 2.401 – 2.473GHz
Operating Channels: 11
Available Transmit Power 2.401 – 2.473GHz (IEEE802.11g/n):
Up to 36dBm EIRP
w30dBm @ 6~9Mbps / MCS0
w29dBm @ 12~18Mbps / MCS1-2
w27dBm @ 24~36Mbps / MCS3-4
w26dBm @ 48~54Mbps / MCS5-7
2.401 – 2.473GHz (IEEE802.11b):
Up to 36dBm EIRP
w30dBm @ 1~11Mbps
Available Receive Gain  2.401 – 2.473GHz (IEEE802.11g/n):
Up to 18dBm
2.401 – 2.473GHz (IEEE802.11b):
Up to 18dBm
Receive Sensitivity (Typical) 2.401 – 2.473GHz (IEEE802.11n): Up to -91dBm
2.401 – 2.473GHz (IEEE802.11g): Up to -92dBm
2.401 – 2.473GHz (IEEE802.11b): Up to -93dBm
Wireless Operation Modes Access Point
Point-to Point Wireless Bridge
Point-to-Multipoint Wireless Bridge
Management and Security XenSmart™ Remote Web-based Management
WEP (128 bit)
WPA-PSK (TKIP, AES, TKIP&AES)
WPA2-PSK (AES)
WPA-PSK/WPA2-PSK Auto (TKIP&AES)
Web Based Firmware Upgrade
QoS: Wireless Multi-Media (WMM) Extensions
Certifications FCC Part 15, Class B

luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460
User Guide
7
Power Requirements Ethernet POE in: 48VDC/0.375A for IEEE 802.3af
Compliance
Power Consumption: 5W Nominal, 13W Max
Temperature Range Operating: 14°F to 131°F (-10°C to 55°C)
Storage: -40°F to 158°F (-40°C to 70°C)
Operating Humidity 5% to 95% (Non-condensing)
Mechanical Dimensions WxHxD: 5.5”(139.7mm) x 5.5”(139.7mm) x
1.5”(38.1mm)
Weight Item: .7 lbs
With Packaging: 1.5 lbs
3 GETTING STARTED
3.1 System Requirements
XDevices Supporting 802.11b, 802.11g or 802.11n
XWeb Browser (Microsoft IE 7.0 and up, Mozilla Firefox 1.0 and up, Safari 1.0 and up,
Google Chrome 5.0 and up)
XCAT5 Ethernet Cable
XAC Power Socket (100 – 240 V, 50/60 Hz)
XInternet Connection to View Documentation Online
3.2 Package Contents
XXAP-1020 Wireless Access Point
XPOE Injector and Power Adapter
XWall Mounting Bracket and Hardware
XQuick Install Guide
NOTE: If any of the listed items are missing or damaged, please contact
the reseller from whom you purchased for return/replacement.
3.3 Safety Information
To maintain the safety of users and property, follow these safety instructions:
XThe XAP-1020 wireless access point is designed for indoor use only. DO NOT
place this access point outdoors. If you require an outdoor access point, please
consider the Luxul XAP-1040.
XDO NOT install this access point in or near hot or humid places, such as a kitchen
or bathroom. Take care to minimize exposure to excessive heat or moisture.

User Guide
8© Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.
XDO NOT pull any connected cable with force. When disconnecting cables, do so
by disconnecting first from the access point. When reconnecting, connect the AP
first and then the Power/data source.
XWhen installing the access point, be sure it is firmly secured to the wall or
mounting bracket.
XAccessories of this access point, such as mounting screws, the POE injector and
power supply may be dangerous to small children under 3 years of age. KEEP All
ACCESSORIES OUT OF THE REACH OF CHILDREN!
XThe access point may become hot when in use for extended time periods. This is
normal and is not a malfunction. DO NOT install this access point where it will
be exposed to paper, cloth or other flammable materials. If not using the electri-
cal box included with the unit, ALWAYS use a properly shielded and UL listed
electrical box for installation.
XThe XAP-1020 contains no user-serviceable parts. If the access point is not
working properly, contact your dealer and ask for help. DO NOT attempt to
disassemble the access point.
4 HARDWARE FEATURES AND INSTALLATION
The XAP-1020 high powered access point is designed for optimal performance as
well as for simple and efficient installation and setup. It implements Luxul’s circular
polarized directional antenna technology and is packaged for installation on a wall
or ceiling. Because the signal generated by the XAP-1020 is directional in nature, the
unit should be placed in a location that allows the antenna face to be “pointed”
towards the desired coverage area. Typically this would be on a top floor ceiling
pointed downwards in a multi-story installation; or for single level or two level
layouts, on a wall pointed towards the desired coverage.
4.1 Front View
For maximum discretion, the front of the XAP-1020 has no LED indicators. It
consists simply of the access point cover with the Luxul icon that indicates proper
top/bottom installation orientation of the access point.

luxul.com | 357 South 670 West | Suite 160 | Lindon, UT 84042 | p: 801-822-5450 | f: 801-822-5460
User Guide
9
XAP-1020 Front View
4.2 Rear View
The rear of the XAP-1020 provides one RJ-45 connection that is used to deliver both
power and data to the access point. It also provides a reset button for restoring the
access point to factory default settings and multiple options for mounting the XAP-
1020 directly on a wall or ceiling or using the adjustable wall mount bracket.
XAP-1020 Rear View

User Guide
10 © Copyright 2011 Luxul. All rights reserved. Trademarks & Registered Trademarks are property of respective holders.
XAP-1020 with Mount
4.3 Top View
The top left side of the XAP-1020 has a small viewing portal for validating System
LED functionality during setup and/or for diagnostic purposes. For discreet installa-
tion, all System LEDs are internal and can only be seen through this viewing portal.
DO NOT open the XAP-1020 to see System LEDs as the access point contains no
user serviceable parts and doing so will void your warranty.
XAP-1020 Top View